How to Make a Glitch Effect in Procreate
StyleFrame Team6 min read
To make a glitch effect in Procreate, open Adjustments → Glitch, choose Artifact, Wave, Signal, or Diverge, and drag your finger across the canvas to set the intensity. For more control, duplicate your artwork onto three layers, tint them cyan, magenta, and yellow, set them to Multiply, offset them slightly, and distort the result with the Push effect. Procreate produces still glitch frames well, but the movement is better built in After Effects or another compositing tool.
Two Ways to Build a Glitch in Procreate
Procreate gives you two routes, and they suit different jobs:
- The built-in Glitch adjustment is fast, applies to a single layer, and gives you adjustable analogue and digital distortion in seconds.
- The manual layer-split method gives you a color-separated, misregistered look you can shape by hand, with each channel on its own layer.
Most finished work combines both. You build the split, then add a Glitch pass for texture. Either way, work on duplicated layers so the original artwork stays untouched.
Method 1: Use the Built-In Glitch Adjustment
Step 1: Open the Glitch Interface
Select the layer you want to affect, tap the Adjustments icon, and choose Glitch. Then tap Layer or Pencil to enter the Glitch interface. A "Glitch" bar appears at the top of the canvas and starts at 0%. Slide right to increase the effect and left to reduce it.
Step 2: Pick the Right Glitch Type
Procreate offers four variants, each modeled on a different failure mode:
- Artifact simulates digital corruption. Light settings give faint horizontal noise, and heavy settings produce blocky, snow-like breakup. Its controls are Amount (how many offset blocks), Block Size, and Zoom (scale of blocks and lines).
- Wave mimics an analogue signal that isn't tuned properly. Light settings nudge the image sideways, and heavy settings lay raster-style scan lines across the whole frame. It's driven by Amplitude, Frequency, and Zoom. If either Amplitude or Frequency is set to None, Wave does nothing, so raise both before judging it.
- Signal combines connected horizontal lines, scattered blocks, and a slight image offset. It's good for a tracking-error or damaged-tape look.
- Diverge offsets horizontal lines and adds chromatic aberration, which makes it the quickest route to an RGB-fringed look.
To learn what each slider does, push the main Glitch amount to 100% and move the secondary sliders back and forth. That shows the range faster than reading any description.
Step 3: Keep It Controlled
A full-frame glitch usually looks cheap. Duplicate the layer, apply the adjustment to the duplicate, then erase or mask areas so the damage appears in bands or around key shapes. Stacking a subtle Artifact pass with a separate Diverge pass often looks better than one pass pushed to the maximum.
Method 2: Build an RGB-Split Glitch Manually
This approach follows the common tutorial workflow and gives you the most art-directable result. It works especially well for logos, type, and graphic shapes.
Step 1: Prepare the Artwork
Import your logo or artwork as a PNG with a transparent background. Duplicate the layer until you have three copies. Hide any spare copy as a backup.
Step 2: Alpha Lock and Tint Each Copy
Turn on Alpha Lock for each layer. You can swipe left with two fingers or choose it from the layer menu. Alpha Lock restricts painting to existing pixels, so you can recolor without disturbing the shape.
Fill one layer with cyan (#00FFFF), one with magenta, and one with yellow (#FFFF00). Use true magenta, #FF00FF. Some tutorials show a green hex value for it, and that gives a different result. Fill each layer with a large soft brush.
Step 3: Set Blend Modes to Multiply
Set all three tinted layers to Multiply. Where the layers overlap, colors combine into darker mixed tones, and where they separate you get colored fringes. This is the core of the look.
If you want an additive, screen-style RGB split instead, use red, green, and blue fills with Screen or Add blend modes. That reads closer to a digital display than a print misregistration.
Step 4: Offset the Layers
Use the Transform tool to move each layer a few pixels in different directions. Turn off Magnetics and Snapping, and use small movements. Horizontal offsets feel more like video errors, and diagonal offsets feel more like print misregistration.
Step 5: Group and Merge
Group the three layers, then merge the group into a single layer. Keep a duplicate of the unmerged group hidden. You'll want it if the client asks for a different offset later.
Step 6: Add Texture and Distortion
Apply these on the merged layer, again working on a duplicate:
- Color Halftone (Adjustments) adds a printed dot pattern.
- Push lets you drag horizontal slices of the image sideways. Use a narrow, hard brush and short horizontal strokes to create sliced displacement.
- Gaussian Blur, applied lightly or to a masked duplicate, softens edges to simulate signal bleed or screen glow.
Finish with a Glitch adjustment from Method 1 on a separate duplicate for scan lines or block noise.
Tips for Better-Looking Procreate Glitches
- Work large. Start with a high-resolution canvas. Glitch artifacts that look crisp on a phone often look soft at broadcast sizes, and you can't add resolution later.
- Vary the slice heights. Real signal errors have uneven band thickness. Uniform stripes look procedural and mechanical.
- Hold back on color. Cyan and magenta fringes should be visible but not dominant. Reduce the opacity of one channel if the image reads as a 3D-glasses effect.
- Keep the subject readable. Leave the main focal point mostly intact and place the damage around it.
- Save variants. Export the clean art, the split version, and the heavily glitched version as separate PNGs. They give you options when you build motion.
Animating the Glitch: Where Procreate Stops
Glitch motion depends on timing, such as a three-frame stutter, a hard cut to a displaced version, or a flicker. These are easier to tune on a timeline with expressions and adjustment layers.
A practical split is to design the look in Procreate, then export and animate it elsewhere:
- Export the clean artwork, the RGB-split version, and one or two heavily glitched states as PNGs.
- In After Effects, place them on a timeline and cut between them on irregular frame counts. Two to four frame holds feel natural, and a perfectly even rhythm doesn't.
- Add a displacement effect, driven by a stretched noise layer, for horizontal tearing.
- Offset the channels by separating RGB and nudging each with a wiggle expression.
- Add scan lines, grain, and a brief exposure flicker on an adjustment layer.
In other compositing tools the logic is the same: hold alternate states, offset channels, and drive distortion with noise.
Quick Recap
- The fastest route is Adjustments → Glitch, with Artifact, Wave, Signal, and Diverge as the four options.
- Artifact is controlled by Amount, Block Size, and Zoom. Wave needs both Amplitude and Frequency above zero to show anything.
- For a custom RGB split, duplicate the art three times, Alpha Lock each copy, tint with cyan, magenta, and yellow, use Multiply, then offset, merge, and distort.
- Add Color Halftone, Push, and a light Gaussian Blur for texture.
- Export clean and glitched states as PNGs, then handle timing and movement in After Effects or your compositor of choice.
Treat Procreate as the place to design the look, and move to a timeline-based tool for rhythm, displacement, and final output.