How to Make a Flower Brush in Procreate
StyleFrame Team7 min read
To make a flower brush in Procreate, draw a white flower on a square canvas, copy it, and paste it into the Shape Source of a new brush in Brush Studio. Then raise Stroke Path > Spacing so each tap stamps a separate flower, set the maximum and minimum size under Properties, and add rotation, jitter, or color dynamics for variation. The same steps work for leaves, petals, or any other stamp brush.
What You Need Before You Start
- An iPad with Procreate (the steps below match Procreate 5.x)
- An Apple Pencil is helpful but not required. Pressure settings can fall back to touch settings.
- A flower design simple enough to read at small sizes
For motion work, think about where the brush will end up. If you plan to animate the flowers in After Effects, you will want clean, isolated stamps on separate layers, so build your brush with that output in mind.
Step 1: Draw the Flower Shape
Open a new square canvas. Square matters because Procreate's shape sources are square, and a non-square canvas can distort or crop the result when you import it.
- Draw your flower in a single color on a plain background. Keep the silhouette bold. Fine detail below a few pixels will vanish when the stamp is scaled down.
- Hide the background color layer in the Layers panel so only the flower remains.
- Fill the flower with white. Select white in the Colors panel and drag the swatch into the shape. You can also lock the layer with Alpha Lock and fill it.
Brush shapes in Procreate work as a mask. White areas are painted, black areas are not, and gray gives partial opacity. If you want soft edges or internal texture, use gray tones inside the shape rather than hard black cuts.
Step 2: Copy the Shape
Open the Actions menu (wrench icon) and tap Copy Canvas. You can also use a three-finger swipe down and choose Copy All. Either puts the flower on the clipboard, ready to paste into the shape editor.
Step 3: Create a New Brush in Brush Studio
You have two ways to start:
- From scratch: Open the Brush Library (paintbrush icon, top right) and tap the + icon. This opens Brush Studio with Procreate's default brush settings.
- From a duplicate: Swipe left on an existing brush, such as Monoline in the Calligraphy set, and tap Duplicate. Then open the copy. This keeps the original safe and gives you a pressure-friendly starting point.
Duplicating is usually faster. Monoline is a clean base because it has little texture or behavior to undo.
Step 4: Import the Flower as the Shape Source
- In Brush Studio, tap Shape in the left-hand menu.
- Under Shape Source, tap Edit to open the Shape Editor.
- Tap Import in the top right and choose Paste to bring in your flower. You can also pick from the built-in Source Library, which includes flowers, flares, and charcoal textures, if you want a quick start.
- Tap Done.
Back in Brush Studio, use the drawing pad to clear the preview and scribble a test stroke. At default spacing, the flowers will overlap into a messy ribbon. That is expected, and the next step fixes it.
Step 5: Set Spacing in Stroke Path
Open Stroke Path. Spacing controls how often the shape is stamped along your stroke. A low value produces a continuous, painterly line. A high value produces separated stamps.
- For a stamp brush (one flower per tap), push Spacing to the maximum.
- For a flower garland or vine effect, use a moderate value. One walkthrough lands around 84%, which gives visible gaps without feeling disconnected.
- For a textured leaf or petal brush that blends into a stroke, keep spacing very low, around 5%.
While you're here, look at Jitter and Falloff. Jitter randomizes the position of each stamp around the path, which helps garlands look organic. Leave it at zero for clean, precise stamps.
Step 6: Set Size Limits Under Properties
Open Properties. The Maximum Size and Minimum Size sliders define the range your brush can reach once you adjust size in the sidebar.
- Raise Maximum Size so you can paint large background flowers without hitting a cap. Some tutorials set it above 200%.
- Set Minimum Size low, around 1%, so you can shrink the brush for tiny filler blooms.
If you want the flower to stay upright regardless of canvas rotation, turn on Orient to Screen. This helps when you rotate the canvas to paint comfortably, because otherwise flowers rotate with the canvas and end up at inconsistent angles.
Step 7: Add Variation So It Doesn't Look Stamped
A single repeated flower looks artificial fast. Add variation in a few places:
- Shape > Rotation and Randomized: Turn up Rotation, or enable Randomized, so every stamp has a different angle. For a single-flower stamp, a full range of rotation can look natural. For tulips or other directional shapes, restrict it.
- Shape > Scatter and Count: Increase Count to drop several flowers per stamp. Add Scatter to spread them out into a small cluster.
- Color Dynamics: Under Stamp Color Jitter, add small hue and brightness variation. This is how you get a field of flowers in subtly different shades from one brush color.
- Apple Pencil: Link pressure to size so a harder press produces a larger flower. Adjust Flow if you want a lighter stamp.
- Taper: If you don't use an Apple Pencil, set Touch taper values so finger strokes still give some variation.
Change one setting at a time and test after each. Brush Studio's drawing pad shows results immediately, which makes isolating a problem simple.
Step 8: Test, Name, and Save
Tap Done and paint on a blank layer. Check for these problems:
- Hard rectangular edges around each flower: The shape has a non-black background. Re-export with a clean black or transparent field.
- Flowers too faint: The shape is gray instead of pure white, or Flow is set too low.
- Flowers cut off at the edges: The artwork touches the canvas boundary. Add padding around the flower.
- Blobs instead of petals: Spacing is too low for a stamp brush, or the shape has too much fine detail.
Rename the brush in Brush Studio. Put it in a custom set so it's easy to find and export.
Variations Worth Building
Once you have one working flower brush, the same workflow gives you a whole kit:
- Leaf brush: Draw a leaf with light internal veining, use low spacing, and enable pressure-based size.
- Stem brush: Use a long, thin shape with spacing at a value that connects the stamps into a continuous line.
- Petal scatter brush: Use a single petal with high Count, strong Scatter, and Randomized Rotation.
- Watercolor flower brush: Use soft gray edges in the shape, lower Flow, and add a textured grain.
If you'd rather skip building your own, curated flower stamp packs exist from various brush marketplaces. Building your own gives you more control over style and licensing, which matters when the artwork ends up in client work.
Using Procreate Flowers in a Motion Pipeline
Procreate is built for stills, but a custom flower brush can feed a motion project if you set up your files with that in mind.
Paint on separate layers. Put each flower cluster, stem, and leaf group on its own layer. Export as a layered PSD and import into After Effects, so you can animate position, scale, and rotation independently.
Keep a transparent background. Hide the background color before exporting so each layer arrives with alpha intact.
Work at high resolution. If the flowers will be scaled up in a composition, paint at a larger canvas size so edges stay crisp.
Quick Reference: Settings That Matter Most
Final Thoughts
A good flower brush comes down to three decisions: a clean white-on-black shape, spacing that matches how you want to paint, and enough variation to hide the repetition. Build one stamp, test it, then branch into leaves, stems, and scatter brushes from the same template. If your flowers are headed for animation, organize your layers and export with transparency from the start, so the illustration carries cleanly into After Effects or whichever tool finishes the shot.