How to Make a Drawing a Brush in Procreate
StyleFrame Team6 min read
To turn a drawing into a Procreate brush, draw it in black and white on a square canvas (2048 x 2048 works well), then open Brush Studio, create or duplicate a brush, and import the drawing as the Shape Source. Procreate reads white as opaque and black as transparent, so your artwork should be white on black, or inverted with a two-finger tap after import. Brushes are greyscale only, so the drawing defines the mark's shape and the color comes from whatever you paint with.
What "drawing as a brush" means in Procreate
Every Procreate brush combines two image sources: a Shape and a Grain. The shape works like a rubber stamp, the silhouette laid down along your stroke. The grain is a texture that shows through that silhouette.
Turning a drawing into a brush means loading your artwork as the shape source (a stamp brush) or, less often, as the grain source (a texture brush). A stamp brush suits repeating motifs such as leaves, stars, scratches, ink splatters, or a logo mark. A grain brush suits surface texture such as paper, dry brush, or halftone.
Because Procreate brushes only support greyscale images, there is no full-color stamp. A multicolor illustration will be reduced to greyscale. If you need a colored, repeatable element, export it as a normal image and place it as a layer instead.
Step-by-step: make a stamp brush from your drawing
1. Set up a square canvas
Create a new 2048 x 2048 canvas from the Gallery. Use a square canvas, since brush sources are best as square images. Set the background to black, or keep it white if you'd rather draw in black.
2. Draw the shape in greyscale
Draw your element so it fills most of the canvas without touching the edges. Leaving a small margin prevents clipped edges when the stamp repeats.
Decide which convention you're using:
- White on black: the white drawing becomes the painted mark. This is the most direct approach.
- Black on white: the drawing reads as transparent against an opaque background, so the brush paints a square with your drawing knocked out. You'll need to invert it.
Greys give you partial opacity, so soft edges and shading carry through. Hard-edged pure black and white gives a crisp, graphic stamp.
3. Get the image into Brush Studio
You have two reliable routes:
- Copy and paste: copy the whole canvas, open the brush's shape editor, and paste. This is the fastest way to iterate: draw, paste, test, adjust, repeat.
- Export and import: share the canvas as a JPG (or a PNG with an opaque background) to Photos, then use Import in the source editor to bring it in.
4. Create the brush
Open the Brush panel and tap + to start a new brush, or swipe left on an existing stamp-type brush and choose Duplicate. Duplicating is often the better route, because the stroke, pressure, and dynamics settings are already sensible. Keep brushes you're building in your own brush set (tap + at the top of the set list) so they don't get mixed up with Procreate's defaults.
5. Replace the shape source
In Brush Studio, go to Shape and tap Edit next to Shape Source. On smaller screens the Edit button may not appear, and you can tap the shape preview directly. Choose Import, then bring in your file or paste from the clipboard.
If the preview looks like a blank square or the reverse of what you drew, tap the image with two fingers to invert it.
6. Tune the stamp behavior
Now the brush exists but probably behaves like a smeared line. Adjust these settings:
- Stroke Path > Spacing: increase it until the individual stamps separate. Low spacing blends them into a continuous stroke.
- Stroke Path > Jitter: adds scatter, useful for debris, particles, or foliage.
- General > Orient to Screen: turn this on if you want the stamp to stay upright rather than rotating with your stroke direction.
- Grain Source: pick a plain white or neutral grain if you want a clean stamp without texture interference.
Tap Done, name the brush under About This Brush, and test it on a fresh canvas at several sizes.
Fixing the most common problems
The shape is blank. This is usually the transparency issue. A PNG with a transparent background and a black drawing imports as a fully transparent square, because black reads as transparent. Either draw in white, put the black drawing on an opaque white background, or save as a JPG.
The stamp is inverted. A two-finger tap on the source image inverts it. Check this before changing anything else.
The edges look boxy. Your artwork likely touches the canvas edge, or the background isn't pure black. Leave a margin and flatten the background to true black.
The stamps overlap into a mess. Raise Spacing. For individual stamps, you often need much higher spacing than the default.
You want color in the stamp. Procreate's brush engine doesn't support it. Use a greyscale stamp and build color on separate layers, or place the colored artwork as a regular layer.
Using a drawing as grain instead
If your drawing is a texture (hatching, ink wash, scanned paper), import it as the Grain Source instead. Crop it to a 1:1 ratio first and turn on Auto Repeat so the edges blend and the texture tiles seamlessly under your stroke. You can combine both: a custom shape for the silhouette and a custom grain for the surface.
Scanned physical marks, such as ink splatters, sponge stamps, or watercolor washes, tend to give more organic results than digitally drawn ones, because they carry irregularities that are hard to fake.
Working this into a motion or VFX pipeline
Custom Procreate brushes are useful beyond illustration. Motion designers and animators often use them to build:
- Hand-drawn texture plates for overlays in After Effects, such as grain, dust, ink bleeds, and paper edges, exported as high-resolution PNGs.
- Matte shapes and brush-stroke reveals to use as track mattes or luma mattes, since a white-on-black brush stroke exports as an instant matte.
- Style frames and keyframe art painted with a consistent brush set so the look holds across a sequence.
- Elements for Cinema 4D or Blender, where hand-painted textures and alpha maps give 3D work a drawn look.
Keep your exports organized. Save at a consistent resolution, name files by brush and version, and keep a flattened black-and-white version alongside any colored one so you can rebuild a matte quickly.
Quick checklist
- Create a 2048 x 2048 canvas.
- Draw your element in white on black (or black on white, then invert).
- Copy the canvas, or export it as a JPG or opaque PNG.
- Duplicate a stamp-style brush, or create a new brush.
- Brush Studio > Shape > Edit > Import (or paste).
- Invert with a two-finger tap if needed.
- Raise Spacing, adjust Jitter, and enable Orient to Screen if you want the stamp upright.
- Test, refine, and save into your own brush set.
Once the first stamp works, the process is quick to repeat, and the copy-paste loop makes it easy to refine a shape until it feels right.