How to Make a Dot Brush in Procreate
StyleFrame Team7 min read
To make a dot brush in Procreate, duplicate the built-in Monoline brush, open Brush Studio, and raise Stroke Path > Spacing (around 60% is a good start) until the stamps separate into distinct dots. Set Taper to none so the dots stay uniform at the start and end of a stroke. Add size jitter for a hand-placed look, then rename the brush under About this brush to save it.
What Makes a Dot Brush Work in Procreate
A Procreate brush is a shape stamped repeatedly along a path. A solid line is a circle stamped so closely that the stamps overlap. A dotted line is the same circle with the stamps pulled apart. Nearly every dot brush comes down to three controls:
- Shape: the stamp itself, usually a plain circle.
- Stroke Path > Spacing: how far apart each stamp lands.
- Dynamics and Apple Pencil settings: whether size, opacity, and color vary from dot to dot or with pressure.
Once you see the brush as a stamp plus spacing, the variants are easy to build: dashed lines, stipple textures, confetti, and halftone-style fills.
Method 1: A Clean Dotted Line in Under a Minute
This is the fastest route and works well for borders, lettering flourishes, and connector lines.
- Open the Brush Library and find the Monoline brush in the Calligraphy set.
- Swipe left on it and tap Duplicate. Always work on a copy so the original stays intact.
- Tap the duplicate to open Brush Studio.
- Go to Stroke Path and drag Spacing to the right. Watch the preview pad: the line breaks into dots as you pass roughly 60–70%.
- Still in Stroke Path, open Taper and set the pressure and touch taper sliders to none. Otherwise you get smaller dots at the start and end of each stroke.
- Open Stabilization and adjust StreamLine and Stabilization to taste. Higher values give smoother curves, which matters when you draw long dotted paths freehand.
- Tap About this brush, rename it (for example, "Dot Line"), and tap Done.
Spacing is the main control. A lower value packs the dots tightly, and a higher one spreads them out. Test at a few brush sizes, because spacing is relative to size and the dots scale with it.
Method 2: Build a Dot Brush From Scratch
If you want more character than a perfectly even line, create a new brush instead of duplicating one.
Set up the base
- In the Brush Library, tap the + icon to create a new brush.
- Open Shape. The default stamp is usually a basic circle, which is what you want here.
- Go to Stroke Path and set Spacing to about 60%.
Add variation with Dynamics
Evenly sized dots look mechanical. To get a more organic result:
- Open Dynamics.
- Under Jitter, raise Size (around 60% gives a noticeable mix of large and small dots).
Remove unwanted opacity changes
A new brush often inherits pressure-based opacity, which makes some dots look faded.
- Open Apple Pencil.
- Under Pressure, drag Opacity all the way to the left so it has no effect.
Optional: color variation per dot
- Open Color Dynamics.
- Under Stamp Color Jitter, increase Hue slightly. Stay around 5–10%. Push it much higher and you get a rainbow rather than a subtle shift.
The color you pick in the color panel becomes the starting color, and each dot drifts slightly from it. Rename the brush, tap Done, and test it on a new layer at several sizes.
Making a Dashed Line Brush From the Same Setup
Dashes are dots with a different stamp. The workflow is nearly identical, with one extra step to define the shape.
- Create a square canvas (1080 × 1080 px works fine). Any square size will do.
- With a Monoline brush at maximum size, draw one short straight line. Hold at the end of the stroke to snap it straight, and make sure it's centered.
- Copy the layer (swipe down with three fingers and tap Copy All, or use the layer menu).
- Duplicate a Monoline brush and open Brush Studio.
- Go to Shape, tap Edit, then Import > Paste. If the shape comes in as black on white, invert it with a two-finger tap. Procreate stamps the white areas of a shape source.
- Tap Done, then set Rotation to Follow Stroke so the dashes align with the direction of your line.
- In Stroke Path, raise Spacing until gaps appear between dashes.
- In Apple Pencil, set opacity pressure to none if you want consistent dashes.
- In Properties, turn off Orient to Screen. If your dashes look wrong or tilt oddly, this is usually the cause.
Experiment with the length and thickness of the line you paste in. A short, fat stamp reads as a dash, and a long thin one reads as a broken hairline.
Making a Stipple or Dotwork Brush
For shading and texture rather than lines, use a different approach:
- Draw a small cluster of irregular dots on a square canvas and import it as the Shape source, or use a single small point.
- Keep the grain source plain or blank so no texture interferes.
- Raise Jitter and Spacing substantially, then lower the brush size.
- Tune the settings while scribbling on the preview pad until the result looks like natural stippling.
Pressure-sensitive size and opacity are worth keeping on for this one. They let you build up density by pressing harder or layering passes, much like dotwork with a pen.
Troubleshooting Common Problems
Dots touch or overlap. Spacing is too low, or the brush size is large. Raise the spacing or reduce the size.
Dots shrink or fade at stroke ends. Taper is still active. Set both Taper sliders to none, and check Apple Pencil pressure for opacity and size.
Dashes don't follow the curve. Rotation isn't set to Follow Stroke, or Orient to Screen is still on.
The stamp looks inverted or muddy. Your shape source is black on white. Invert it in the Shape editor.
Wobbly dotted curves. Increase StreamLine and Stabilization, or draw the path with a shape tool and then use the brush to stroke over it.
Exporting Dot Brush Artwork for Motion Projects
If you're a motion designer, a dot brush is useful for more than illustration. Hand-drawn dotted paths, stipple textures, and dash patterns make good overlays for title cards, map routes, and graphic accents.
To get artwork out of Procreate cleanly:
- Draw on its own layer and hide the background color so the export keeps transparency.
- Export as a transparent PNG for single elements, or as a layered PSD if you want to separate pieces in After Effects.
- Draw at a generous canvas size. Dots scale with the stamp, so a larger canvas gives you room to scale the artwork in your comp without softening the edges.
- Keep each variation (dots, dashes, stipple) on separate layers so you can animate, mask, or trim them independently.
In After Effects, dotted line art pairs well with Trim Paths on a shape layer, or you can reveal a raster dotted line with a mask or a track matte. Which you choose depends on whether you need the dots to stay evenly spaced during the reveal.
Quick Reference
Start with the simple dotted line, then layer in jitter, color variation, or a custom shape. Each change takes only a few settings, and you'll end up with a small set of reusable brushes you can carry into any project.