How to Make a Dashed Line Brush in Procreate
StyleFrame Team7 min read
To make a dashed line brush in Procreate, draw a thick, short straight line on a square canvas and copy it. Then duplicate the Monoline brush and open Brush Studio. Paste the line as the brush's Shape source, set Rotation to "Follow Stroke," and raise Stroke Path > Spacing until gaps appear between the dashes. Finally, turn off "Orient to Screen" and set Apple Pencil opacity pressure to none so every dash renders at the same weight and angle.
What You Need Before You Start
You need Procreate on an iPad and the stock Monoline brush from the Calligraphy set. Any clean, hard-edged round brush also works as a starting point. An Apple Pencil is useful for testing, but the build doesn't depend on one.
The brush has two parts:
- A shape source. This is the single dash, a short rectangle or a rounded bar.
- A stroke path. This controls how the dash repeats, rotates, and spaces itself along your stroke.
Once you see it that way, every variation (long dashes, dots, tapered ticks) is just a different shape or a different spacing value.
Step-by-Step: Build the Dashed Line Brush
1. Create the dash shape on a square canvas
Make a new square canvas. The exact size matters less than the aspect ratio. Procreate's shape editor works with a square source, so a 1080 × 1080 px canvas is fine. A larger canvas gives you a sharper shape source if you plan to use the brush at big sizes.
Select the Monoline brush, set its size to maximum, and draw one short, thick horizontal line. Hold your pencil at the end of the stroke to snap it straight with QuickShape. Don't make the line touch the canvas edges. Leave generous margins on both sides.
Center the line using Transform with Snapping turned on, so the yellow guides confirm it sits in the middle of the canvas. A centered shape keeps the dashes aligned to the path of your stroke instead of drifting to one side.
2. Copy the shape
Swipe down with three fingers to open the copy and paste menu, then tap Copy All. You can also copy the layer from the Layers panel. Either way, the clipboard now holds your dash.
3. Duplicate a brush
Open the Brush Library, find Monoline, swipe left, and tap Duplicate. Don't edit the original. If you want a clean slate, create a new brush library called something like "Dashes" and put your custom brushes there so they're easy to find.
4. Paste the shape into Brush Studio
Tap the duplicate to open Brush Studio, then go to Shape. Tap Edit above the shape source, choose Import, then Paste.
Procreate reads the shape source as white on black: white areas lay down paint, black areas don't. If your dash comes in as a black line on white, tap with two fingers in the editor to invert it, then tap Done.
5. Set rotation to follow the stroke
Still in the Shape panel, drag Rotation all the way to the right until it reads Follow Stroke. Without this, every dash stays horizontal regardless of the direction you draw. With it, dashes rotate to follow curves, which is what you want for borders, motion paths, and hand-drawn annotation lines.
6. Open up the spacing
Go to Stroke Path and raise Spacing. At low values the dashes overlap into a solid line. Somewhere around 60–70% usually produces clear gaps, but this depends on the width of your shape source, so adjust until the gap-to-dash ratio looks right for your use.
If you want dashes that look rigid and mechanical, keep Jitter at zero. If you want a looser, sketchy feel, add a small amount of jitter under Stroke Path or Dynamics.
7. Remove the settings that distort the dash
This is the step most tutorials rush through, and it's where most brushes go wrong.
- Taper: Under Stroke Path > Taper, set the tapers to none unless you want the start and end dashes to shrink.
- Apple Pencil pressure: Under Apple Pencil, drag the opacity pressure to zero so dashes don't fade with light pressure. Check the size pressure as well if you want consistent weight.
- Orient to Screen: In Properties, turn this off. If it's on, the shape can behave oddly as you rotate the canvas or draw at different angles.
- Maximum size: Raise it in Properties, so you can scale the brush up for larger work. A very low maximum size is a common reason a brush feels limited.
8. Stabilize and name it
Open Stabilization and add some StreamLine. Dashes along a wobbly path look sloppy, and a little smoothing makes curves cleaner. Then tap About this brush, rename it (for example "Dash – Square"), and tap Done.
Test on a blank layer. Draw straight lines, tight curves, and circles. If the dashes bunch up on curves, lower the spacing slightly or raise StreamLine.
Troubleshooting Common Problems
Dashes touch or merge into a solid line. Increase Spacing, or shorten the dash in the shape source.
Dashes look faint or uneven. Pressure is still affecting opacity. Set the Apple Pencil opacity curve to none and check that the shape source is pure white, not gray.
Dashes are rotated sideways. Your shape was drawn vertically, or Rotation isn't set to Follow Stroke. Redraw the dash horizontally and re-import it.
The edges look soft or jagged at large sizes. The shape source was too small or drawn with a soft brush. Rebuild it on a larger canvas with a hard-edged brush.
Dashes shift when you rotate the canvas. Turn off Orient to Screen.
Variations Worth Building
Once you have the base brush, you can create a small family of brushes quickly by duplicating it and changing one thing at a time:
- Dotted line: Duplicate Monoline, raise Spacing, and set Taper to none. You don't need a custom shape.
- Long dash / short dash: Change the length of the line in your shape source and re-import.
- Rounded dash: Draw the source line with a round-capped brush.
- Dash-dot pattern: Draw a dash plus a small dot in the same shape source, then space them within the square canvas. Spacing then repeats the pair as a unit.
- Textured or chalk dash: Add a grain source in the Grain panel for a more organic look.
Using Procreate Dashed Lines in a Motion Workflow
For motion designers and animators, a Procreate brush is most useful when you want a hand-drawn quality: annotated callouts, map routes, sketchy HUD elements, or storyboard arrows. There are some practical limits to keep in mind.
Procreate's dashes are raster. The brush stamps pixels, so you can't change dash length or gap afterward the way you can with a vector stroke. If you need parametric control, a vector tool is the better choice. Use Procreate when the irregularity of a hand-drawn line is the point.
Export at the resolution you need. Draw on a canvas sized for your composition, or export at a higher resolution and scale down. Export with a transparent background so you can bring each line into your compositing software as its own layer.
Animate frame by frame. If you want a line to draw on or "boil," draw a series of frames and export them as an image sequence for your compositing software. Hand-drawn frame-by-frame dashes naturally have a subtle wobble that vector tools don't give you.
Consider timing in comp. For a simple draw-on of a static Procreate stroke, a layer mask or a wipe effect on a PNG works, but the dashes will reveal along the mask edge rather than appearing one by one. For a precise dash-by-dash reveal, rebuild the path as a vector.
Quick Reference
Build the brush once, save it in its own library, and you'll have a reusable dashed line for illustrations, storyboards, and animation frames. Adjust the spacing and shape to match whatever the project needs.