How to Make a Cutout in Procreate
StyleFrame Team7 min read
Procreate has no dedicated background-removal button, so you make a cutout by selecting the subject and then cutting it to its own layer or hiding the rest with a layer mask. The fastest route is the Selection tool in Automatic mode, followed by a three-finger swipe down and Cut & Paste. For photos, press and hold the subject in the Photos app and drag the lifted subject onto your canvas. To make text- or shape-shaped holes, invert the selection and fill a new layer.
Which Procreate Cutout Method Should You Use?
Method 1: Cut Out a Subject With Automatic Selection
Automatic selection is the quickest route when the subject contrasts with its background.
- Import your image (Actions > Add > Insert a photo) and make sure it sits on its own layer.
- Tap the Selection tool (the S-shaped icon) and choose Automatic at the bottom of the screen.
- Tap the background and drag your finger or Pencil left or right. The drag controls the selection threshold: a higher value grabs more similar tones, a lower value grabs fewer.
- Check the marching ants. If the selection covers the background, you're done with the hard part. If it covers the subject, tap Invert.
- Swipe down with three fingers and choose Cut to delete the background, or Cut & Paste to move the subject onto its own layer.
If the tool bleeds into the subject, temporarily paint a flat, contrasting color behind or around the edge. The tool reads tonal differences, so giving it a clearer boundary often fixes a stubborn selection.
Method 2: Draw the Selection by Hand
Use Freehand when the subject and background share similar tones, or when you need precise geometry.
- Tap points around the object to create straight segments, or drag to draw curves.
- Close the loop by tapping the starting dot. The marching ants disappear from the outline and become the active selection. This is normal behavior, not a lost selection, and it confuses many first-time users.
- Use Add to include another region and Remove to subtract from the current selection before you close it.
- Raise the Feather setting slightly (a small amount is usually enough) so the edge doesn't look sawn off against new backgrounds.
Zoom in with a pinch while placing points. Selecting at a high zoom level produces cleaner edges around hair, fur, and fine detail than selecting at fit-to-screen.
Method 3: Lift the Subject From Your Photos App
If your iPad's operating system supports it, you can skip selection entirely for photos:
- Create your Procreate canvas first. Match the aspect ratio to your final delivery, such as 4:5 for social posts or 9:16 for vertical video.
- Open the Photos app in Slide Over beside Procreate.
- Press and hold the main subject until an outline appears.
- Drag the lifted subject into your canvas.
The subject lands on your canvas without its background. It's very fast for people, products, and animals, but the system's edge detection is a black box. You can't adjust a threshold, so expect to clean the edges manually afterward.
Method 4: Make a Cutout Shape or Text Knockout
A "cutout" in Procreate can also mean a hole in a layer, as in the popular paper-cutout look.
- Create or add your text or shape on its own layer.
- Open the Layers panel, tap that layer's thumbnail, and choose Select.
- Tap Invert in the selection toolbar.
- Add a new layer above, tap its thumbnail, and choose Fill Layer. The color fills everything except your shape, leaving a knockout.
- Hide the original text or shape layer.
For the paper-layered look, duplicate each colored layer twice. Turn on Alpha Lock for the first duplicate and fill it white to create a paper edge. Do the same on the second duplicate with black, then blur it or lower its opacity to create the shadow. Offset each stack slightly and the layers read as physical paper.
Refine the Edges Without Destroying Pixels
Cutting pixels is permanent unless you undo. For anything that might change, a mask is safer.
- Use a layer mask. Tap the layer, choose Mask, then paint black to hide areas and white to reveal them. If you hid too much, paint it back.
- Clean fringing. Light halos from the old background are the most common giveaway. Paint over the edge on the mask with a small hard brush at low opacity, or shrink the selection by a pixel or two before cutting.
- Use Alpha Lock for color fixes. If the edge picked up a color cast, lock the layer's alpha and paint over only the existing pixels with a soft brush set to a matching color.
- Check against contrast. Put a dark layer and a bright layer beneath your cutout in turn. Edge problems that hide on one background show up on the other.
Export a Cutout for After Effects and Other Compositing Apps
Many motion designers use Procreate to make assets such as characters, props, textures, and lettering, then animate them elsewhere. A few settings make the handoff painless.
- Hide the Background Color layer in the Layers panel before exporting. Otherwise your transparency is flattened into a solid color.
- Export as PNG (Actions > Share > PNG) for a single transparent image, or PSD to keep layers, which After Effects imports as a composition with separate layers.
- Work large. If a cutout will be scaled up or pushed in on with a camera move, build the canvas at the highest resolution your device allows. Procreate's maximum layer count drops as canvas size grows, so plan your layer structure first.
- Separate what will move. Put arms, eyes, shadows, and props on their own layers before export. It's much easier than re-cutting them in After Effects.
- Mind color. Check your canvas color profile (RGB for screens) and test one asset in your comp before exporting a full set.
In After Effects, import the PSD as a composition, retain layer sizes, and parent or puppet-pin the pieces for animation. For stills you'll composite in Nuke, export PNG or TIFF with an alpha channel and verify whether the file is premultiplied before you merge it.
Troubleshooting Common Cutout Problems
The selection disappears when I close it. Closing the loop completes the selection, so the outline you drew vanishes. That means the selection is active, not lost.
Automatic selection grabs too much or too little. Adjust the threshold by dragging, change the contrast of the area, or switch to Freehand.
Jagged edges. Increase your canvas resolution, apply a small feather, or refine with a soft mask edge.
My export has a white or colored background. The Background Color layer is still visible. Turn it off and export again.
The subject looks pasted on. A cutout needs matching light, shadow, and edge softness. Add a contact shadow on a layer below it and adjust the edge color toward the new background.
Where Styleframe Fits for Video and Motion Work
Procreate is a strong tool for hand-finished cutouts, but it isn't designed for cutting out large numbers of video frames. If your cutouts come from video frames or AI-assisted sequences, doing them one at a time becomes impractical.
is an AI video and motion tool. Its Remove Background tool helps when you need isolated subjects from generated or existing imagery.
A practical workflow might be: paint or refine key art in Procreate, bring it into a video tool such as Styleframe to generate motion, then export an image sequence and composite in After Effects or Nuke as you normally would. Procreate remains the place for precise hand edits, while a tool like Styleframe can cover the motion and the batch of frames that would be tedious to cut manually.
Quick Checklist
- Put the subject on its own layer.
- Select with Automatic for clean contrast, or Freehand for precision.
- Invert if needed, then Cut & Paste to a new layer.
- Prefer a layer mask over erasing.
- Clean edge fringing and test on light and dark backgrounds.
- Hide the background color and export PNG or layered PSD.
- Separate any element you plan to animate.
Choosing the right method for the subject is what saves the most time.