How to Make a Brush Fully Opaque in Procreate
StyleFrame Team7 min read
To make a Procreate brush fully opaque, set the sidebar opacity slider to 100%, then check the brush itself. Open Brush Studio, go to Properties, and set both Minimum and Maximum Opacity to 100%. If it still looks see-through, adjust the pressure curve, set Opacity Jitter to 0, switch off Wet Mix dilution, and check the brush's glaze setting. Some brushes, such as Gouache, are designed never to reach full opacity, so for those the fix is choosing a different brush.
Why a Procreate brush won't paint at full opacity
Opacity in Procreate isn't controlled by one setting. The mark you see is the product of several settings stacked together, which is why moving the sidebar slider to the top sometimes changes nothing.
Brushes fall into three groups:
- Brushes that are never fully opaque by design. Gouache and other brushes cap their output intentionally.
- Pressure-sensitive brushes. Round Brush and Flat Brush in the Painting set can reach 100%, but only if your Apple Pencil pressure reaches the top of the curve.
- Brushes that stay at or near full opacity regardless of pressure. Many brushes in the Inking set behave this way, and Syrup is a common example.
Identify which group your brush falls into before you change anything. If it's the first group, no setting will fix it, and you're better off picking or building another brush.
Step 1: Check the sidebar opacity slider and layer settings
Start with the obvious items, because they're the most common cause.
- Brush opacity: Drag the lower slider in the sidebar all the way up. A slider sitting at 98% looks like 100% at a glance.
- Layer opacity: Open Layers, tap the letter to the right of the layer name (usually "N"), and confirm the opacity slider is at 100%. A layer at 80% makes every stroke on it look washed out, no matter how solid the brush is.
- Blend mode: Make sure the layer is set to Normal. Multiply, Overlay, and similar modes change how strokes read against what's beneath.
- Clipping masks and Alpha Lock: These restrict where paint lands. If strokes seem to disappear or look faint, check whether the layer is clipped to something beneath it.
Step 2: Fix the Apple Pencil pressure curve
If a brush looks opaque with your finger but faint with the Pencil, pressure is often the reason. With the default curve, you may have to press harder than is comfortable to reach full opacity.
To change it:
- Open Actions (wrench icon) → Prefs.
- Tap Pressure and Smoothing → Edit Pressure Curve.
- Drag the curve upward so that moderate pressure maps to higher output.
A steeper curve means you reach full opacity with a lighter touch. This is a global change that affects every brush, so adjust it a little at a time and test with a few different brushes. Some artists with wrist or hand strain modify their curve for exactly this reason.
Step 3: Edit the brush in Brush Studio
When the global curve isn't enough, change the brush itself. Make a copy first so you keep the original.
- In the Brush Library, swipe left on the brush and tap Duplicate.
- Tap the copy to open Brush Studio.
- Go to the Properties tab.
- Drag Maximum Opacity and Minimum Opacity to 100%.
Setting the minimum to 100% means the brush can never fall below full opacity, and setting the maximum to 100% makes sure it can reach it. This change can often (though not always) fix "my brush is transparent" problems, particularly with brushes that rely on pressure.
Settings that can override your opacity values
If the brush is still inconsistent, other panels may be overriding the Properties values:
- Dynamics → Opacity Jitter: Pull this to 0. A brush that lays down random opacity on each stamp may simply be carrying jitter.
- Apple Pencil settings (pressure and tilt): Reduce or remove the opacity response to pressure and tilt so the stroke doesn't vary.
- Stroke properties: Check taper. Tapering fades the ends of a stroke, which reads as partial transparency.
- Wet Mix: Set dilution to zero. Dilution thins the paint and lowers opacity as you work.
- Shape source: Confirm the shape image is solid white where you want full coverage. Grey pixels in the shape source produce partial opacity.
- Grain: A textured grain can affect opacity. Set it to none, or make sure the grain image has no transparent pixels.
Step 4: Stop overlapping strokes from darkening
A common complaint is that a second pass over a stroke looks darker than the first, or that overlap shows inside one stroke when opacity is below 100%. The brush's glaze setting in Brush Studio is one place to check. Try different glaze settings and compare. This won't change overall opacity, but it may help a single stroke read as one consistent value, which matters when you're painting flat shapes.
Step 5: Remove partially transparent edge pixels
"Fully opaque" can mean two things: the center of a stroke is solid, or every pixel in the mark is either fully opaque or fully transparent. The second is harder, and it's what hard-edged mattes, pixel work, and clean cel-style shapes need.
Soft pixels at the edge usually come from shape filtering and anti-aliasing. To get hard, aliased edges:
- Open Brush Studio and go to the Shape section.
- Set Shape Filtering to No filtering.
- Make sure your shape source has no grey or semi-transparent pixels.
With filtering off, edges become hard and aliased instead of smoothed. That's the right tradeoff for pixel art, black-and-white comic linework, and mattes where you don't want in-between values. If you only need a quick solution, the Syrup brush in the Inking set makes fully opaque, aliased marks, although one user still saw some partially transparent edge pixels when zoomed in until they turned off shape filtering. A slower workaround, which some artists use, is duplicating a layer and merging down repeatedly to push faint pixels toward opacity. It works, but it's tedious, so fixing the brush is the better approach.
Quick troubleshooting checklist
Getting clean opaque art into a motion pipeline
If your Procreate work feeds After Effects, Premiere Pro, Blender, or Nuke, opacity discipline pays off downstream. Storyboard panels, hand-drawn textures, matte shapes, and frame-by-frame animation all depend on predictable alpha.
A few practical habits:
- Export PNGs with transparency for elements you'll composite, and keep layers at 100% unless you intentionally want a baked-in transparency value.
- Avoid baking in layer opacity when you can. It's easier to set opacity in your compositing app, where it stays adjustable.
- Check edges at 100% zoom in After Effects. Semi-transparent fringe pixels can show up as halos against dark or bright backgrounds.
- Use hard, filter-free brushes for mattes. Solid black-and-white shapes give you cleaner luma mattes and track mattes than soft-edged ones.
Summary
Making a Procreate brush fully opaque means working through the full chain: sidebar and layer opacity, pressure curve, Brush Studio Properties, jitter, dilution, glaze, and shape filtering. Start with the quick checks, duplicate the brush before editing, and accept that a few brushes, like Gouache, won't ever reach full opacity by design. Once your marks are solid and your edges are clean, exporting to After Effects or other compositing tools becomes far more predictable.