How to Make a Brick Brush in Procreate
StyleFrame Team7 min read
To make a brick brush in Procreate, draw a brick or a tileable section of brick wall on a square canvas, then open Brush Library, tap +, and import the artwork in Brush Studio. Use it as the Shape Source for a stamp brush that lays individual bricks along a stroke, or as the Grain Source with texturized behavior for a brush that fills any area with a fixed brick pattern. Then adjust spacing, jitter, and color dynamics until the strokes read as real brickwork.
Choose the Right Type of Brick Brush
Two approaches cover most needs, and they behave quite differently.
- Stamp brush (Shape Source): Each dab is one brick, or a short run of bricks. It suits you when you want control over placement: drawing a crooked chimney, a broken wall edge, or a path of pavers. It is also easier to vary, since every brick can differ slightly.
- Pattern fill brush (Grain Source, texturized): The brick pattern is fixed to the canvas, and your stroke reveals it. This is faster for large walls, backgrounds, and environment concept art, and it keeps courses perfectly aligned across separate strokes.
Many artists build both. Premade free packs often include long-brick, short-brick, and stone variants, but building your own gives you the proportions, mortar width, and wear that match your project. If you use someone else's brushes, check the license before using them in client work.
Prepare the Brick Artwork
Set up the canvas
Create a square canvas. 1024 × 1024 px works for a stamp shape, and 2048 × 2048 px is a better choice for a wall tile. Square sources import cleanly into Brush Studio.
For the wall tile, turn on Canvas > Drawing Guide > Edit Drawing Guide and set a grid that matches your brick size. Brick proportions vary, so pick a length-to-height ratio that suits your project; this example uses 3:1, including the mortar joint. On a 2048 px tile, a workable layout is:
- Two bricks across (about 1024 px each)
- Six courses (rows) down (about 341 px each)
Draw the bricks in running bond
Running bond is the familiar pattern where every other row is offset by half a brick. Draw the first row, then shift the next row by half a brick (512 px in this layout). Bricks that cross the left or right edge must continue on the opposite edge so the tile repeats without a visible seam. In practice, that means drawing a half brick at each edge on the offset rows. Do the same logic top to bottom.
Keep the artwork high contrast and grayscale. Procreate reads shape and grain sources by their light and dark values, so soft midtones become soft transparency. For a crisp brick, use solid values with slightly rough edges. For an aged wall, add chips, pits, and uneven corners to the brick edges rather than relying on blur.
Check polarity before you import
Whether light or dark areas become "paint" depends on the source type, and it is easy to get backwards. Preview the result in Brush Studio's drawing pad. If your bricks appear as gaps and your mortar appears as paint, use the Invert option in the source editor.
Method A: Build a Stamp Brick Brush
- Open a Brush Library, tap + to create a new brush, and open Shape.
- Under Shape Source, tap Edit, then Import, and choose your single-brick image (a copy, a photo, or a file).
- Back in Brush Studio, go to Stroke Path and raise Spacing until each dab sits next to the last, not on top of it. Start high and reduce until bricks touch with a visible mortar gap.
- Set Streamline moderately high so the stroke path stays steady and courses run straight.
- In Shape, add a small amount of Rotation > Randomized (a few percent, not a lot) so bricks sit slightly off-axis. Too much looks like scattered debris.
- Add a touch of Scatter only if you want a loose, stacked look. For clean courses, leave it at zero.
Add per-brick variation
Real walls show tonal differences from brick to brick. Open Color Dynamics and use Stamp Color Jitter: small values for hue, saturation, and brightness. Brightness jitter does most of the work, with a little hue shift for firing differences. Keep these low, since an overdone effect reads as confetti.
Under Apple Pencil and Properties, decide whether pressure should change size. For bricks, locking size is usually better, since brick size should stay consistent. Set Maximum Size to your working scale and minimum size close to it, then reduce pressure-driven size changes.
Method B: Build a Brick Wall Fill Brush
- Create a new brush and open Grain.
- Under Grain Source, import your tileable wall image.
- Set Behavior to Texturized so the pattern stays locked to the canvas instead of moving with the brush. This is what keeps your courses aligned across strokes.
- Adjust Scale to set brick size relative to your canvas. You can change this later per project, so pick a sensible default.
- Raise Depth so the grain strongly masks the stroke. High depth means clearer brick and mortar separation.
- Open Shape and use a simple, hard shape (a plain round or square) so the brick pattern, not the shape, defines the result.
- Set Maximum Size large, since this brush is meant for filling areas.
Because the grain decides where paint lands, the mortar lines stay clear. Put a mortar-colored layer underneath and paint bricks on a layer above. That gives you separate control over brick color, mortar color, and overlay effects like grime.
Tune and Test the Brush
Use the drawing pad in Brush Studio, then test on a real canvas. Look for these problems:
Test at several sizes. A brush that looks right at one scale may show blurry edges when enlarged, so import a higher-resolution source if you plan to paint large backgrounds.
Add wear and variation
A single perfect pattern repeats obviously. A few options keep it believable:
- Create a second brush with chipped or cracked bricks and alternate between them.
- Paint a dirt, moss, or soot layer on top using a separate texture brush, with the brick layer clipped beneath it.
- Duplicate the brush and modify the grain scale, so you have a close-range and a distance version.
Save, Organize, and Share the Brush
Name the brush in About this brush, and put it in its own set (for example, "Masonry"). To share or back it up, swipe left on the brush in the library and choose Share, which exports a .brush file. Keep your source images as well, since you will want to revise the pattern later and re-import.
Using Brick Brushes in a Motion Pipeline
For motion work, the brush is a means to an asset, not the final output. A practical workflow:
- Paint the wall, props, or background on separate layers (bricks, mortar, grime, highlights).
- Export as a layered PSD or as transparent PNGs.
- Import into After Effects, Photoshop, or Nuke and separate the layers for parallax, camera moves, or relighting.
Keep a flat, front-on version of the wall as well. It is far easier to project onto geometry in Cinema 4D or Blender than a version with baked-in perspective.
Where Styleframe fits
If your brick art needs to move, is an AI video and motion tool that can help extend it without replacing your hand-built assets. Your Procreate brushwork stays the creative source, and Styleframe can handle the motion and style-transfer step.
Quick Checklist
- Square canvas with a grid sized to your brick unit
- Running-bond layout with continuous edges for seamless tiling
- High-contrast artwork with imperfect, chipped edges
- Stamp brush: Shape Source, spacing, light rotation, color jitter
- Fill brush: Grain Source, Texturized behavior, high Depth
- Tested at multiple scales and saved into a named set
Once the two base brushes work, variations are quick to produce: change the source image for stone, cobble, tile, or weathered concrete, and keep the same settings as a starting point.