How to Make a Box in Procreate
StyleFrame Team8 min read
To make a box in Procreate, draw a rough rectangle and hold your Pencil at the end of the stroke until QuickShape snaps it into a clean quadrilateral. Keep holding and add a second finger to lock it into a perfect square. For a 3D-looking box, turn on a Drawing Guide (Isometric or Perspective) with Drawing Assist and draw three connected faces, shading each one differently. Fill any face by dragging a color into it with ColorDrop.
Procreate has no dedicated shape tool, so every box comes from QuickShape, a selection, or a guide. Which one you pick depends on whether you need a flat panel, a precise rectangle, or a dimensional object.
Which kind of box do you need?
"Box" covers three different jobs, and each has a fast route:
- A flat square or rectangle (UI panel, lower third, comic frame): QuickShape or the Rectangle selection.
- A perfectly sized rectangle with a clean fill: Rectangle selection plus ColorDrop.
- A 3D box or cube (product mockup, isometric prop, storyboard object): Drawing Guide with Drawing Assist.
Method 1: Draw a box with QuickShape
QuickShape is the quickest way to get a clean box, and it behaves the same way for squares, rectangles, and other basic forms.
- Create a new layer and pick a brush with a reasonably hard edge. Clean edges make the result easier to fill and reuse.
- Draw a rough four-sided shape, ending where you started so the stroke closes.
- Don't lift your Pencil at the end. Hold it still for a moment and the stroke snaps into a quadrilateral.
- While still holding, place a second finger on the canvas. An uneven rectangle becomes a perfect square.
- Still holding, drag to scale or rotate the shape. Holding a second finger while you drag rotates in 15-degree increments, which is useful for keeping a box square to the canvas or setting a precise tilt.
- Release. An Edit Shape button appears in the notification bar at the top of the canvas.
Refine the shape in Edit Shape mode
Tap Edit Shape to get transform nodes on the box. Drag a node to adjust that corner or edge, or drag the shape itself between the nodes to scale it uniformly. Tap anywhere on the canvas to commit.
If QuickShape is firing too early or too late, go to Actions → Prefs → Gesture Controls → QuickShape. You can adjust how it's invoked and tune the touch and Pencil shortcuts. Artists who draw a lot of panels or UI blocks usually benefit from spending a minute here.
A common QuickShape frustration
If your rectangle keeps coming out slightly skewed, you probably released before the second snap. QuickShape first snaps to the nearest form, and only the second-finger step pushes it to a perfect square. Hold through both steps and release only once the shape looks right.
QuickShape also produces a stroke, not a filled object. Procreate doesn't currently let you apply or adjust a stroke on an existing shape, so decide on stroke weight and brush before you draw. If you need a different outline, redraw the box rather than trying to restyle it afterward.
Method 2: Make a precise rectangle with the Selection tool
When you want a solid filled box without an outline, skip drawing and select it instead.
- Create a new layer.
- Tap the Selection button to open the Selection toolbar.
- Choose Rectangle.
- Drag across the canvas to define the box.
- Tap Add if you want to combine more rectangles (or ellipses) into one compound selection, such as an L-shaped panel or a window-and-frame layout.
- Drag your color from the color circle into the selection (ColorDrop) to fill it.
You can keep navigating with the usual pinch, pan, and rotate gestures while in Selection mode, so zooming in to place a corner precisely doesn't interrupt the selection.
When you tap another tool, the selection is committed. Semi-transparent moving diagonal lines around the selected area tell you it's active. From there you can paint inside it, smudge, erase, ColorDrop, or transform it.
When to use selections over QuickShape
- You want a flat, solid-fill box with no outline.
- You're building something from several rectangles that must align.
- You need to paint or erase strictly within the box boundary.
Selections are also the better choice when the box is a mask or a matte. Fill it on its own layer, and you have a clean shape you can reuse as a clipping base.
Method 3: Build a 3D box with Drawing Guide
A cube is three visible faces with consistent angles. Procreate's drawing guides help keep those angles honest.
Isometric box
- Turn on the Drawing Guide and open its editing options.
- Choose Isometric and adjust the grid so it's visible but not distracting.
- Tap Done, then enable Drawing Assist on the layer you'll draw on.
- On that layer, draw the top face as a rhombus, then the left face and the right face. Drawing Assist helps keep your strokes aligned to the grid.
- Put each face on its own layer or fill each one separately. Use a light value on top, a mid value on one side, and a darker value on the other to establish a light direction.
Perspective box
- In the Drawing Guide editing options, choose Perspective.
- Place a vanishing point for a one-point box, or add more for two-point or three-point views.
- With Drawing Assist on, draw the front face as a rectangle.
- Draw lines from its corners toward the vanishing point, then close off the back edge with lines parallel to the front.
- Erase or hide construction lines you don't need on a separate guide layer.
Keep construction lines on their own layer. When you're ready to refine, you can lower or hide it without affecting the final shapes.
Shading the box
Stick to a single light source. Tops are usually lightest, the side facing the light is mid-tone, and the opposite side is darkest. Use ColorDrop for flat fills, then add gradients or texture on clipped layers above each face so the underlying shape stays clean.
Tips for production-friendly boxes
Designers who bring Procreate work into motion pipelines tend to run into the same issues. A few habits help:
- Name and separate layers. Put each face, outline, shadow, and guide on its own named layer so you can pull them apart later.
- Work larger than you think you need. Start with a canvas size that survives scaling in your comp, especially if the box will move toward the camera.
- Keep the box on a transparent background. Export a PNG or hide the background layer first so you don't have to key it out.
- Use consistent angles. If you're building several boxes for one scene, reuse the same guide settings so they all sit in the same space.
- Keep an unshaded version. A flat, clean box is easier to restyle, recolor, or use as a reference later.
Using a Procreate box as a reference for AI-assisted motion work
A sketched box is more useful than it looks. Because it has clear edges, clear faces, and a defined light direction, it makes a good starting reference for generative tools that need something concrete to follow.
is an AI video and motion tool that works from your own references, such as images and video clips. A box drawn in Procreate can serve as one of those references, for example as a starting or ending state for a short animation.
This doesn't replace drawing the box well. The better your construction and shading in Procreate, the more precise your reference is for everything downstream.
Common problems and fixes
The box won't snap. Make sure you're holding your Pencil in place at the end of the stroke, and check QuickShape settings under Gesture Controls.
The fill leaks. ColorDrop needs a closed shape. Zoom in and look for tiny gaps at the corners, or use a Rectangle selection instead.
Corners don't meet on the isometric box. Check that Drawing Assist is on for the layer you're drawing on, not just the guide itself.
The box looks flat. Add value contrast between faces, and check that edges recede consistently toward your vanishing point.
The edges look soft. Zoom in, switch to a harder brush, or use a selection-based fill for crisp boundaries.
Quick reference
Start with whichever matches your end use. For flat graphics, QuickShape and selections are enough. For anything that needs depth, set up the guide first, draw the three faces, and keep your layers organized so the box carries cleanly into any other tool in your pipeline.