How to Make a Border Brush in Procreate
StyleFrame Team7 min read
To make a border brush in Procreate, duplicate a simple brush such as Monoline, edit it in Brush Studio, and pair it with a second brush through Dual Brush so one stroke draws the fill and a darker or wider stroke draws the edge. If you want a decorative frame instead, build a motif as a custom Shape source and combine it with a thin line brush so the line stays continuous through the pattern. Results depend on blend mode and on keeping your canvas unrotated, so test on a scratch layer before committing to a final piece.
What "border brush" Means in Procreate
Two different effects get called border brushes, and they need different builds.
- Edge-border brush: every stroke gets a darker outline around its outer edge, similar to the border option in Clip Studio Paint. Artists coming from CSP often want this, and Procreate has no single toggle for it.
- Decorative border brush: a stroke that lays down a repeating pattern such as leaves, scallops, or dashes along a continuous line, which is useful for frames, dividers, and lettering accents.
Decide which one you need first. The edge-border build relies on blend modes and layering, and the decorative build relies on Shape sources and Dual Brush.
Build an Edge-Border Brush
The goal is a stroke whose fill sits inside a darker rim, and where lifting the pen and starting again doesn't draw a new rim inside paint you've already laid down. Procreate can approximate this, though not perfectly.
Step 1: Duplicate a base brush
In the Brush Library, swipe left on a clean brush such as Monoline or a hard round and tap Duplicate. Never edit the original, because you will want to revert while experimenting. Rename the copy right away, for example "Border Ink."
Step 2: Set up two-tone color behavior
Open Brush Studio. Many community border brushes use both your primary and secondary colors: one becomes the rim and the other becomes the center. This is why some downloadable outline brushes ask you to pick a secondary color for the "middle" of the stroke. Removing the secondary color can give you a transparent, outline-only look.
Step 3: Choose the blend mode that darkens the edge
Edge darkening comes from how the brush blends with what is underneath. Color Burn and Multiply are the usual starting points. Rendering options such as burnt edges also darken stroke edges, and the blend mode you pair them with changes how dark the result gets. Expect to adjust these a few times, since the same settings behave differently on different base brushes.
Step 4: Test for overlap behavior
Draw a blob, lift your pen, then draw across it. If a new rim appears inside the existing paint, the brush is stamping its border each time. You have a few options:
- Draw each shape on its own layer, so strokes don't interact.
- Accept a stacked-edge look as a stylistic choice.
Community builds of these brushes note a trade-off here. The settings that make overlapping strokes look clean can also leave slightly pixelated edges. If you see this, try a higher-resolution canvas and a smoother Shape source before rebuilding from scratch.
Build a Decorative Border Brush
This is the approach behind most "border brush" tutorials: two brushes combined so a pattern repeats along a line without breaking the line itself.
Step 1: Start with a square canvas
Create a square canvas for drawing the brush shape. Shape sources are square, so a square canvas keeps your motif from distorting. Draw in black on white.
Step 2: Draw the motif
Draw one repeating unit: a leaf, a small flower, a scallop, or a dash. Keep it centered with some padding, because motifs that touch the edges get clipped. Simple shapes read better at small sizes.
Step 3: Edit the first brush
Duplicate Monoline, then open Brush Studio and make these changes:
- Shape: edit the Shape source and import your motif, either from Photos or by copying from the canvas.
- Stroke path: adjust Spacing so the motifs sit apart without overlapping. Raise it for open patterns and lower it for dense ones.
- Orientation: fixed orientation keeps motifs upright, while following the stroke rotates them as the line curves. Pick based on the look you want, and note that fixed motifs depend on a straight, unrotated canvas.
- Properties: set a maximum and minimum brush size so the brush stays consistent.
Step 4: Create the second brush for the line
Duplicate Monoline again and keep it as a clean, continuous line. Low spacing and no jitter make this a solid thread running through your pattern. This is the "persistent line" that keeps leaves and decorations from floating separately, and it is what makes the result a border instead of scattered stamps.
Step 5: Combine them with Dual Brush
Open the Dual Brush settings on your pattern brush and select the line brush as the second brush. Check the blend mode and scale so the line sits at the right thickness relative to the motifs. Save it, then test.
Step 6: Test, then check limitations
Draw straight lines, curves, and a closed rectangle. Watch for these problems:
- Rotated canvas: if the canvas is rotated or your iPad orientation changed, fixed-orientation motifs can look off. Reset the rotation and try again.
- Tight curves: motifs can bunch up or gap when spacing is too low or too high.
- Size changes: the pattern scales with brush size, so you may need two or three size presets.
Quicker Alternatives When You Don't Need a Brush
A custom brush is the right call when you will reuse it dozens of times. For one-off needs, these are faster:
- Outline, then fill: draw the outline with a narrow brush and use ColorDrop to fill the inside.
- Duplicate and offset: duplicate the shape layer, fill the lower copy with a darker color, and scale it up slightly. This works well for variable outlines and drop shadows.
- Blur and threshold for stickers: merge your art to one layer, duplicate it, push the lower copy's brightness to white, apply Gaussian Blur, then adjust the threshold to harden the edge. It is quick, though the border follows your art's edge, so soft or low-opacity brushes give uneven results. A hard-edged brush can clean up what the method misses.
- Leave it for compositing: if the border is a fixed graphic, a stroke or outline effect in your compositing app may be faster than building a brush.
Using Procreate Borders in a Motion Pipeline
Borders drawn in Procreate often end up in video, as hand-drawn frames, lower-third accents, title card edges, or textured mattes. A few practices keep them useful in After Effects, Premiere Pro, or Nuke.
- Export with transparency: save a PNG with a transparent background, and hide the background color layer first.
- Draw at delivery scale: work at or above your comp resolution so you don't have to upscale a soft raster border.
- Separate layers by element: keep the border, fill, and any texture on their own layers so they can be animated or re-timed independently.
- Draw frame variations: if you want a boiling or wobbling line, draw two to four versions and cycle them at a low frame rate.
Troubleshooting Checklist
- Border color is reversed: the primary and secondary colors may be swapped for the brush's design. Swap them or check the brush's blend mode.
- Rim appears inside existing paint: switch to one layer per shape.
- Jagged edges: increase canvas resolution, smooth the Shape source, or adjust the rendering settings.
- Motifs look skewed or misaligned: reset canvas rotation and confirm the orientation setting.
- Pattern gaps on curves: reduce Spacing slightly and re-test on tight turns.
Final Notes
Border brushes in Procreate are a combination exercise. You duplicate a base brush, adjust shape, spacing, and blend behavior, and pair it with a second brush when you need a continuous line. Expect trial and error, because the same settings produce different results on different base brushes. Save your best versions with clear names, keep the originals untouched, and test every new brush on a scratch layer before using it in client work.