How to Lower Transparency in Procreate
StyleFrame Team7 min read
To lower transparency in Procreate, you raise opacity: open Layers, tap the letter (usually "N") beside the layer name, and drag the slider to the right until the layer is as solid as you want. To make a brush stroke more solid, drag the lower slider on the Sidebar upward. For a selected area on a layer, tap that layer in the Layers panel with two fingers and slide on the canvas. If you meant the opposite and want something more see-through, use the same controls and move them the other way.
Lower Transparency vs. Lower Opacity
"Transparency" and "opacity" are two ends of one scale. At 100% opacity, a pixel is fully visible. At 50%, it is half see-through. So "lowering transparency" means increasing opacity, while "lowering opacity" means making something fade out.
Many people search for "lower transparency" when they actually want a layer to look fainter, so this guide covers both directions. Procreate gives you three places to control this: the brush, the whole layer, and a selection. A fourth option, the Adjustments > Opacity tool, exists in older versions.
Method 1: Change Layer Opacity
This is the most common fix, and it affects every pixel on the layer.
- Tap the Layers icon in the top right.
- Tap the small letter to the right of the layer name. It reads "N" by default, which stands for Normal blend mode.
- Drag the slider under it right to make the layer more solid, or left to make it more transparent.
This change is non-destructive. You can come back later and set a different value without losing any paint, which makes it the safest option for work that is still evolving.
Two-Finger Shortcut
Tap the layer in the Layers panel with two fingers at once. The opacity slider appears at the top of the screen, and you can slide it to adjust. It does the same thing as the first method with fewer taps once you are used to it.
Method 2: Raise Brush Opacity
If strokes look washed out as you paint, the problem is the brush, not the layer.
- Pick your brush.
- Find the lower slider on the Sidebar.
- Drag it up for more opaque strokes, or down for more transparent ones.
When the Slider Is at Maximum and Strokes Are Still Faint
Many brushes respond to Apple Pencil pressure. A light touch can produce transparent marks even when the opacity slider is at 100%. Before blaming the settings, press harder and see whether the stroke gets denser. If it does, the culprit is pressure, not the slider. You can check your pressure settings, or choose a brush that responds less to pressure.
Method 3: Change Opacity on a Selection
Sometimes you only want part of a layer to change, such as one shape on a layer with several elements.
- Make a selection using the Selection tool and whichever mode you prefer (such as Automatic).
- Open the Layers panel.
- Tap the layer containing the paint with two fingers at the same time.
- Slide a finger right on the canvas to increase opacity (lowering transparency) or left to reduce it.
- Exit the mode to apply the change.
Know That This Is Destructive
Unlike the layer slider, selection opacity is baked in once you leave the mode. You can undo it right away, but you cannot revisit and re-tweak it later in the project. If you are unsure of the final value, duplicate the layer first or isolate the area on its own layer and use the layer slider instead.
Common Gotcha
If you have two-finger tap set to undo in your gesture settings, tapping the canvas with two fingers will undo a stroke instead. The two-finger tap has to land on the layer in the Layers panel, the same spot you would normally tap once to open layer options. Also note that the regular layer slider still affects the entire layer even when a selection is active. That is why people are often surprised that "the whole layer changed."
Method 4: The Adjustments > Opacity Tool (Older Versions)
Older versions of Procreate include an opacity tool under Adjustments. Tap Adjustments > Opacity, and a bar at the top of the screen shows the current value, starting at 100%. Slide your finger right to make the layer more solid and left to make it more transparent.
Buttons along the bottom let you cancel and exit, undo a change, redo it, or reset while staying in the tool. Tap the Adjustments icon again, or choose another tool, to commit the change. If you do not see this option in your version, use the layer slider or the two-finger method instead.
Troubleshooting: Why It Still Looks Transparent
If you have raised opacity and the result still looks faint, check these:
- Brush opacity vs. layer opacity. They are separate controls. A layer at 100% holding strokes painted at 40% brush opacity will still look semi-transparent. Raising the layer slider does not fix strokes that were painted thin.
- Pencil pressure. As above, light pressure can reduce density on pressure-sensitive brushes.
- Layer stacking. A layer below or above may be affecting what you see. Toggle layers off one at a time to isolate the issue.
- Clipping masks. If a layer is clipped to the layer beneath it, paint appears only where the base layer has pixels. A stroke that seems to vanish may simply fall outside that base.
- Blend mode. If the letter beside the layer isn't "N," the blend mode changes how the layer combines with what's underneath, which can look like a transparency problem. Reset it to Normal to rule it out.
- Stacked duplication. If a layer is at 100% and still too light because the paint itself is thin, duplicate it. The duplicate adds density on top of the original. Merge the two once you are happy with the result.
Working Habits That Save Time
- Keep opacity adjustable as long as possible. Prefer the layer slider over selection opacity until you are sure about the value.
- Separate elements onto their own layers. It lets you control each element's opacity independently and avoids the selection workaround entirely.
- Name your layers. When you export or hand off, someone else, or future you, can find what needs adjusting.
- Test on both light and dark backgrounds. Opacity looks different depending on what is behind it. A shape at 70% over a white canvas will read differently over a dark composite.
Taking Procreate Art Into a Motion Pipeline
For motion designers and compositors, opacity in Procreate is usually a means to an end: a styleframe, a texture, a matte painting element, or a hand-drawn overlay headed for After Effects, Nuke, or Blender. A few practical points:
- Decide where opacity should live. If you will animate a fade in After Effects, keep the element at 100% opacity in Procreate and control it in the timeline. Baking in a reduced opacity limits your room to adjust later. Check that your exported file keeps layer opacity the way you expect before relying on it.
- Hide the background color layer when exporting an element with transparency, and check that the exported file keeps the transparency rather than a flat color.
- Export elements separately. Individual layers are easier to composite, retime, and grade than a single flattened image.
Quick Reference
FAQ
Is lowering transparency the same as increasing opacity? Yes. Lower transparency means higher opacity, so the content becomes more visible and solid.
Why does my brush look transparent at 100% opacity? Apple Pencil pressure may be reducing density. Press harder, or check your pressure settings and brush behavior.
Can I change opacity on part of a layer without affecting the rest? Yes. Make a selection, then two-finger tap the layer in the Layers panel and slide on the canvas. Remember that this is a destructive change.
Why did the whole layer change when I had a selection active? The standard layer opacity slider affects the entire layer, even when a selection is active. Use the two-finger layer tap to affect only the selection.