How to Get True White on Procreate
StyleFrame Team7 min read
The fastest way to get true white in Procreate is to open the Color panel, go to the Value tab, and type FFFFFF into the Hex field (or set Brightness to 100% and Saturation to 0%). Then confirm the canvas uses an RGB color profile, paint at 100% opacity with a hard, full-flow brush, and export as PNG. If white still looks gray or tinted, the cause is usually a CMYK canvas profile, a low-opacity brush, a layer blend mode, or display settings like True Tone, not the color itself.
This guide covers each of those causes, how to verify the result numerically, and how to keep that white intact when the artwork moves into After Effects, Nuke, or another compositing tool.
Set pure white with the Hex value
Procreate's color wheel makes it easy to land on "almost white," such as 98% brightness with a hint of saturation. Typing the value avoids that.
- Tap the color circle in the top-right corner to open the Color panel.
- Switch to the Value tab at the bottom.
- Find the Hex field and enter
FFFFFF. - Tap Done.
You can also use the sliders in the same tab. In HSB mode, set Saturation to 0 and Brightness to 100. In RGB mode, set Red, Green, and Blue each to 255.
Check the canvas color profile first
If you've entered FFFFFF and the swatch still doesn't look right, check the canvas color profile.
Go to Actions > Canvas > Canvas Information > Color Profile. Canvases created with a CMYK profile (SWOP, for example) behave differently from RGB canvases, and the color panel may show unexpected results. Users have also reported cases where an OS update caused white to appear as black or disappear from the color wheel on certain CMYK canvases. In those cases, the workaround was to copy the work into a canvas with a different profile.
For animation, video, and compositing work, use an RGB profile. sRGB is the safest choice if the artwork is headed to a video timeline. Display P3 works if your whole pipeline is color-managed for it. CMYK is only appropriate if the final output is print, and even then, pure screen white is not the same as paper white.
If you need to change an existing canvas, duplicate it first, then change the profile on the copy and compare. Profile conversions can shift other colors, not just white.
Make sure the white is actually 100% white
The color picker can be correct while the pixels on the canvas are not. Several things cause this.
Brush opacity, flow, and pressure
Apple Pencil pressure can drive opacity or flow in many brushes. A light stroke with white paint over a darker area gives you a semi-transparent white that mixes with what's underneath. For solid white:
- Set the brush opacity slider to 100%.
- Pick a brush with no pressure-to-opacity mapping, or reduce that mapping in Brush Studio.
- Avoid textured or grainy brushes, which intentionally leave gaps.
Layer opacity and blend modes
Check each layer in the Layers panel. A layer set to 90% opacity, or to Multiply, Overlay, or any non-Normal mode, will not read as white even if the paint on it is FFFFFF. Set the layer to Normal at 100% to test.
Fill instead of painting
For big white areas, don't scrub with a brush. Drag the white swatch from the color circle onto the shape (ColorDrop) or use Selection with Fill Layer.
The background color layer
The canvas has a Background color layer at the bottom of the Layers panel. Tap it and set it to FFFFFF explicitly rather than trusting the default. If you hide it, your canvas is transparent, and exporting as PNG will carry that transparency. That's useful for compositing but means "white" is no longer present in the file.
Adjustments that crush highlights
If the art is already painted and the whites are slightly dull, use Adjustments > Curves. Drag the top-right node, which represents the lighter areas, to the left to brighten them. Use the histogram to see where your brightest values sit. This pushes everything above that point to pure white, so apply it on a duplicate layer or a copy of the canvas, and keep an eye on soft gradients that may start to band or lose detail.
Verify with the eyedropper and your eyes
Don't judge white by looking at it. Press and hold on the canvas to bring up the eyedropper, sample the area, then open the Color panel and read the Hex field. If it reads FFFFFF, the pixel is pure white.
Your display also affects what you perceive:
- True Tone on iPads shifts the white point toward the room's ambient light, which can make FFFFFF look warm.
- Night Shift does the same, deliberately.
- Brightness at a low level makes white look gray.
- Reflective screen protectors can add a color cast.
For color-critical work, turn off True Tone and Night Shift, and compare on a calibrated monitor. The file values matter more than the iPad's appearance.
Export without losing the white
Export settings can change white values in subtle ways:
- PNG is lossless and preserves FFFFFF. Use it for stills and transparent assets.
- JPEG applies compression, which can nudge flat white regions to values like 254 or add faint noise near edges. Avoid it for anything you plan to key, composite, or grade.
- PSD keeps layers if you want to finish in Photoshop or separate elements for animation.
- Animated exports (MP4, GIF) are subject to their own compression and color conversions. GIF in particular is limited to a palette.
Also remember the embedded color profile. If the canvas is Display P3 and your video project assumes Rec. 709 or sRGB, you can see differences in saturation and sometimes in the way white sits relative to other tones. Match your working spaces on both ends.
Keep true white true in After Effects and Nuke
Once artwork leaves Procreate, white can drift for reasons that have nothing to do with the iPad.
In After Effects:
- Check the project's working color space and bit depth. In an sRGB or Rec. 709 pipeline, FFFFFF should read as 255/255/255 (1.0 in 32-bit float) in the Info panel.
- Right-click the footage and check Interpret Footage > Color Management to confirm the assigned profile matches the file's embedded profile.
- For transparent PNGs, check the alpha interpretation. Straight versus premultiplied errors show up as dark or white fringes on edges, which is especially visible around white linework.
- Be careful with effects, adjustment layers, and tone-mapping at the end of your comp. A Lumetri or Curves layer can lower the white point without you noticing.
In Nuke:
- Set the Read node's colorspace to match the file (typically sRGB for a Procreate PNG). With the correct transform, sRGB white maps to 1.0 in linear.
- Use a pixel analyzer or the viewer's sample readout to confirm values. If white lands at 0.95 or below, something upstream (the wrong colorspace, a gain, or a grade) is changing it.
- Check premultiplication with Unpremult/Premult nodes around color operations on elements with alpha.
A simple test: put a flat FFFFFF Procreate export next to a solid generated in your compositing app and compare their pixel values. If they match, your pipeline is clean.
Quick troubleshooting checklist
If your white still isn't white, work through these in order:
- Does the Hex field read FFFFFF?
- Is the canvas profile RGB (sRGB for video work)?
- Is the brush at 100% opacity with no pressure-driven fade or grain?
- Is the layer at 100% opacity and in Normal blend mode?
- Does the eyedropper sample the painted area as FFFFFF?
- Are True Tone, Night Shift, and low brightness turned off while judging?
- Did you export as PNG with a profile your destination expects?
- In After Effects or Nuke, do the pixel values read 255 or 1.0 after import?
Most "off-white" problems resolve at steps 2, 3, or 4. Fix those first, then verify downstream, and you'll have white you can rely on from the iPad through to the final comp.