How to Get Symmetry Tool on Procreate
StyleFrame Team7 min read
The symmetry tool is already built into Procreate as part of the Drawing Guide, so there is nothing to download. Open Actions (the wrench icon) → Canvas, switch on Drawing Guide, tap Edit Drawing Guide, then choose Symmetry at the bottom of the screen. Next, turn on Assisted Drawing and make sure Drawing Assist is enabled on the layer you are painting on, or your strokes will not mirror.
Where the Symmetry Tool Lives in Procreate
Procreate does not list symmetry as a brush or a toolbar button. It is a mode of the Drawing Guide system, which is why people often can't find it. On Procreate for iPad:
- Tap the Actions icon (the wrench) in the top left.
- Open the Canvas tab.
- Toggle Drawing Guide on.
- Tap Edit Drawing Guide.
- Tap Symmetry in the bottom panel.
- Tap Options to choose the type of symmetry.
- Make sure Assisted Drawing is on, then tap Done.
The guide appears as thin lines over your canvas. Whatever you paint on one side is reproduced in real time on the other.
Procreate Pocket on iPhone
The path differs slightly on Procreate Pocket. Expand the top toolbar with the ellipsis, go to Actions → Canvas, and tap Symmetry. To adjust the grid, tap Edit Drawing Guides.
The Drawing Guides interface starts condensed at the bottom of the screen. Drag the grey handle upward to reveal color, opacity, thickness, Rotational Symmetry, Assisted Drawing, and the symmetry type. Drag it down to collapse the panel. Confirm with the blue tick instead of Done.
Enable Drawing Assist on Each Layer
This step causes most "symmetry isn't working" problems. Symmetry only applies to layers that have Drawing Assist switched on.
- Tap the layer in the Layers panel.
- Tap Drawing Assist so the layer shows an "Assisted" label.
- Paint. Strokes now follow the guide.
Every new layer needs this toggle. Procreate's own documentation notes that paint, smudge, and erase strokes are only mirrored when Assisted Drawing is on. The reverse also happens: if your strokes mirror even though the guide is hidden, check the Assisted Drawing setting.
The Four Symmetry Types
Once you are in Symmetry options, you can choose one of four modes. Vertical is the default.
Vertical
A guideline runs down the middle of the canvas. Drawing on the left appears on the right, and vice versa. This suits faces, bottles, logos, and characters seen head-on.
Horizontal
A guideline runs across the middle. Top-half strokes appear on the bottom half. It works well for reflections in water or glass, and for top-to-bottom mirrored shapes.
Quadrant
Both a vertical and a horizontal guide divide the canvas into four sections. A stroke in one quadrant repeats in the other three. It is useful for tile-like patterns and ornamental frames.
Radial
The canvas is split into eight segments using horizontal, vertical, and diagonal lines. A stroke in one segment repeats across the other seven. It suits mandalas, kaleidoscopic textures, and star or snowflake-style shapes.
Move, Rotate, and Reset the Guide
The guide does not have to sit in the center. Two nodes control it:
- Blue (Positional) node: moves the whole grid across the canvas.
- Green (Rotational) node: rotates the guide lines.
With vertical or horizontal symmetry, rotating the guide produces mirrored results at an angle. To return the grid to its default position, tap either node, then tap Reset.
Mirror vs. Rotational Symmetry
New guides use Mirror Symmetry, which reflects and flips your strokes across the guideline. Toggle Rotational Symmetry and each stroke is reflected and rotated, so the copy is flipped horizontally and vertically at once.
The distinction matters when you are designing marks that should look consistent. Mirror mode gives you left-right pairs like wings or leaves. Rotational mode gives you pinwheel or turbine-style repeats. Switch between them on a scratch layer to see the difference before committing.
Adjust the Guide's Appearance
You can tune how the guide looks without affecting your art:
- Color: use the hue bar at the top of the Drawing Guides screen.
- Opacity: from invisible to fully opaque.
- Thickness: from invisible to noticeable.
On a busy illustration, lower the opacity or thin the lines so you can judge the artwork cleanly. Drawing Assist also nudges strokes to match the direction of the guide lines, and it is on by default in Symmetry mode.
Troubleshooting: Guide Visible but Nothing Mirrors
Run through this checklist:
- Drawing Assist is off on the layer. Tap the layer and enable it.
- Assisted Drawing is off in the guide settings. Re-open Edit Drawing Guide and switch it on.
- Symmetry is not the active guide. Check that the Symmetry button is highlighted (blue) in the Drawing Guides screen. On Pocket, the readout at the bottom of the settings shows the current type after "Symmetry:".
- You are on the wrong layer. Symmetry is per layer, so a new layer needs the toggle again.
Limits to Know About
Radial symmetry in Procreate uses a fixed set of eight segments. Users on Procreate's feedback forum have asked for adjustable segment counts, citing six-sided snowflakes, triangles, hexagons, and wheel spokes as examples where eight doesn't fit. There is no built-in setting for this.
The common workaround is to draw one section with vertical symmetry, then duplicate, rotate, and arrange copies manually using snapping. It works, but it is slower than a native repeat count. If you routinely need 3-, 5-, 6-, or 12-fold symmetry, plan for that extra step or consider doing the repeat construction in another tool.
Using Procreate Symmetry in a Motion Pipeline
For motion designers, animators, and VFX artists, Procreate symmetry is most useful at the asset-making stage, not as a finished deliverable. A few practical uses:
- Symbol and logo exploration: sketch balanced marks quickly, then rebuild the best one as vector shapes in After Effects or Illustrator.
- Mandala and kaleidoscope sources: radial symmetry gives you raw material for looping backgrounds or title treatments.
- Texture and pattern elements: quadrant symmetry produces tileable-feeling motifs you can refine and repeat in compositing.
- Character and creature design: vertical symmetry speeds up front-view turnarounds and masks.
- Style frames and concept boards: quickly produce symmetrical hero art to anchor a look.
Keep each element on its own layer so you can export layered files and separate pieces for animation later. Name your layers before exporting, because assisted layers carry no special meaning outside Procreate. Once the art is in After Effects, Cinema 4D, Blender, or Nuke, it is ordinary raster content.
Where Styleframe Fits After Procreate
Once you have a symmetrical illustration, you may want to turn it into motion without redrawing every frame. is one option to explore for that. Treat it as a way to extend art you have already designed, not a replacement for the design step itself.
Quick Reference
Frequently Asked Questions
Is the symmetry tool a paid add-on? No. It is part of Procreate's Drawing Guide and available inside the app.
Why do I have to turn on Drawing Assist for every layer? Symmetry is applied per layer. A layer without Drawing Assist ignores the guide, even when it is visible.
Can I change the number of radial segments? Not in Procreate's built-in tool, which uses eight. Manual duplication and rotation is the usual workaround.
Does symmetry affect erasing and smudging? Yes, when Assisted Drawing is on, paint, smudge, and erase strokes are all mirrored on the assisted layer.