How to Get Streamline on Procreate
StyleFrame Team6 min read
In Procreate, StreamLine lives in Brush Studio. Tap the brush you want in the Brush Library to open Brush Studio, choose the Stabilization tab, and raise the StreamLine Amount slider until wobbles in your line smooth out. StreamLine is a per-brush setting, so you adjust it on each brush you use. In Procreate Pocket it is a slider under the Stroke tab of the brush settings.
How to Find StreamLine in Procreate (iPad)
- Open your canvas and tap the Brush icon to open the Brush Library.
- Select the brush you want to modify.
- Tap that brush a second time to open Brush Studio.
- In the left-hand list, choose Stabilization.
- Find the StreamLine section and drag the Amount slider up.
- Scribble on the Drawing Pad in Brush Studio to preview the result.
The Drawing Pad matters because it lets you test the setting without touching your artwork. Draw a few long curves and a few quick flicks to see how the setting behaves.
Duplicate the brush first. Swipe left on the brush in the library and tap Duplicate before you edit. That keeps the original intact. If you change several settings and lose track, open Brush Studio, go to About this Brush, and tap Reset Brush to restore the defaults.
Amount vs. Pressure: What the Two Sliders Do
StreamLine has two controls:
- Amount smooths wobbles and shakes in the line. Higher values give smoother, more even strokes. Lower values or zero give more natural, less processed linework.
- Pressure changes how pressure is applied across a stroke. Higher values produce a longer, smoother pressure ramp. Lower values make pressure register more quickly as you press down.
Set Amount first, then adjust Pressure if line weight feels sluggish or too abrupt at the start of strokes.
Recommended StreamLine Settings by Task
There is no single correct value. These starting points come from a few artist tutorials, and you should tune them to your hand and your Pencil.
Cranking the value to maximum can make lines feel elastic or automated, which cuts against the point of drawing by hand. Raise it gradually and stop when the line is clean enough for the job.
StreamLine vs. Stabilization vs. Motion Filtering
All three sit on the same Stabilization tab, and they are often confused:
- StreamLine smooths out wobbles and shakes in your line as you draw. It is the one most associated with inking and calligraphy.
- Stabilization takes a moving average of the stroke and draws that on the canvas. The higher it goes, the straighter and more deliberate your strokes become, but the less freedom you have.
- Motion Filtering works similarly to Stabilization with a more advanced algorithm. Instead of averaging out wobbles, it removes them, which produces even straighter lines.
At maximum, Stabilization and Motion Filtering make it difficult to draw anything but straight, controlled paths. One artist's tutorial settled on roughly 30% Stabilization and about 20% Motion Filtering as a workable blend. Treat that as a data point, not a rule.
A practical workflow is to start with StreamLine alone. Add a little Stabilization only if the line still feels loose, and reach for Motion Filtering last.
How to Get StreamLine on Procreate Pocket
On the iPhone version, the path is slightly different:
- Open your project in Procreate Pocket.
- Select the brush you want to use.
- Tap the brush icon in the top menu to open the brush settings.
- Open the Stroke tab.
- Drag the Streamline slider to the right to raise the smoothing percentage.
A setting of about 30–40% is a sensible default. It smooths the line without removing the dynamics of your sketch. Small screens can make smooth strokes harder to achieve, so Pocket users may benefit from a bit of smoothing.
Stabilization You Can Apply to Every Brush
If you want smoothing across all brushes at once, use the global setting instead of editing brushes one at a time:
- Tap the Actions (wrench) icon.
- Go to Prefs > Pressure & Smoothing.
- Adjust the Stabilization slider.
Global stabilization overrides brush behavior, so a low value around 10–15% is a reasonable starting point. The risk is forgetting it is on. If your Pencil suddenly feels laggy or less responsive, check this slider first. It is one of the most common beginner headaches.
Troubleshooting StreamLine Problems
StreamLine seems to be on even at 0%. Procreate staff have said that no StreamLine is applied when the slider is set to None. What users notice at zero is more likely the way Procreate now interprets Apple Pencil's predictive strokes. Some users also reported curved lines and vanishing stroke ends on certain versions, so if the behavior looks like a bug rather than smoothing, check for app updates and report it through Procreate's support channels.
Lines feel laggy or too stiff. Lower the brush's StreamLine Amount, then check global Stabilization under Prefs > Pressure & Smoothing. Also check Stabilization and Motion Filtering on the brush itself.
One brush behaves differently from another. StreamLine is stored per brush. A brush that ships with built-in smoothing will feel different from one that does not, so compare their Stabilization tabs.
You edited a brush and want it back. Use About this Brush > Reset Brush, or keep a duplicate of the original.
Why Clean Linework Matters in a Motion Pipeline
If you work in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, you may be using Procreate for what it does best: fast, hand-drawn input. Typical uses include:
- Storyboards and animatics
- Style frames and look-development paintings
- Character and prop design
- Hand-inked line art for cleanup or rotoscope-style work
- Texture and matte painting elements
In those cases, smoother lines are not only cosmetic. Shaky inking becomes obvious once it is animated, scaled, or composited. A consistent StreamLine value across a set of brushes helps keep line quality uniform across a whole set of frames or assets, which is easier to manage than fixing wobble later.
A useful habit is to save a small set of duplicated brushes with fixed StreamLine values, for example a rough brush at a low value, a working brush at 30–40%, and an inking brush at 70–100%. Switching between them is faster than re-tuning sliders mid-project.
The practical takeaway is that the quality of your input matters. A clean, deliberately smoothed Procreate frame gives later steps in your pipeline better source material than a shaky sketch. Getting StreamLine dialed in is a small step that pays off when those drawings become the foundation for motion.
Quick Recap
- iPad: Brush Library → tap the brush → Brush Studio → Stabilization → StreamLine → Amount.
- Pocket: Brush settings → Stroke tab → Streamline slider.
- Starting values: a low value for sketching, 30–40% for general drawing, 70–100% for inking.
- Duplicate first, and use Reset Brush if you need to undo changes.
- Check global Stabilization under Prefs > Pressure & Smoothing if your Pencil feels laggy.
- Use StreamLine, Stabilization, and Motion Filtering in that order, adding more only when the line needs it.