How to Get Straight Lines on Procreate
StyleFrame Team7 min read
To draw a straight line in Procreate, put your Apple Pencil or finger down, draw the line, and hold at the end without lifting. After a brief pause, the stroke snaps straight. While still holding, touch a second finger to the screen to lock the angle to 15° increments, then lift to commit. For shapes, the same hold gesture activates QuickShape, and for lines that must stay aligned to a guide, the Drawing Guide with Assisted Drawing does the job.
Draw a Straight Line with QuickLine
QuickLine is the fastest method, and it needs no menu or tool change. It works with the Paint or Erase tool, so you can use it for linework, masking, or cleanup.
- Select a brush and a layer.
- Draw a rough line in the direction you want.
- Do not lift the pencil at the end of the stroke. Hold still for a moment.
- The wobbly stroke straightens into a clean line between your start and end points.
- Keep holding and move the pencil to adjust the length and angle. The start point stays fixed, and the end point follows you.
- Lift to commit.
The hold is what trips most people up. If you lift even slightly early, you get the freehand stroke you drew. If the line isn't snapping, hold for a bit longer before you release. If it snaps too eagerly, you can change the delay (covered below).
Snap to 15° Angles
Straightening a line is not the same as making it perfectly horizontal or vertical. A line that snaps straight at a slightly off angle is still off. To lock the angle, do this:
- Draw and hold until the line straightens.
- With the pencil still down, touch a second finger anywhere on the canvas.
- The line now snaps in 15° increments, so horizontal, vertical, 45°, and 30°/60° angles are all easy to hit.
- Move the pencil to rotate through the increments, then lift.
This is the quickest way to get clean horizontals and verticals for frames, UI mockups, storyboard panels, safe-area guides, and title layouts. It also helps with hard-edged design elements you plan to animate later, where a one-degree tilt shows up as soon as something moves.
Draw Clean Shapes with QuickShape
QuickShape uses the same hold gesture but applies it to closed or multi-segment forms. Draw a rough triangle, rectangle, circle, or a polyline of your own design. Keep the pencil on the screen at the end of the stroke, and Procreate cleans up the edges and curves.
Once the shape appears, you can still drag to change its size and orientation before lifting. Touching a second finger converts it to a regular form: a triangle snaps to equal-length edges, a rough circle becomes a true circle, and so on.
Edit the Shape After Drawing
When a QuickShape is created, a notification appears at the top of the canvas. Tap it to open the edit shape menu. From there you can:
- Switch the shape type, for example turning a circle into a square.
- Use the transformation nodes that appear around the shape to adjust individual points.
Handle this right away. The edit menu is only available immediately after you create the shape. If you need to adjust it later, use the Transform tool instead.
A practical tip for polylines: if you plan to fill the shape with color, make sure the start and end points meet. A gap, even a tiny one, means a fill can leak into the rest of the layer. Use the edit nodes to close it before you move on.
Use the Drawing Guide for Persistent Straight Lines
QuickLine is a gesture, so you do it fresh for each line. If you need many lines that follow the same guide, the Drawing Guide is more efficient. Open the Actions menu (wrench icon), go to Canvas, and turn on Drawing Guide. Then use Edit Drawing Guide to set up your guide and turn on Assisted Drawing.
With Assisted Drawing on, your strokes follow the guide. This is useful for architectural environments, hard-surface design, and layout work where consistency matters more than a single clean line.
Two things to remember:
- Assisted Drawing is a property of the layer. A layer with it on shows "Assisted" under its thumbnail. Tap the thumbnail to open Layer Options and toggle Drawing Assist.
- There is also a global setting for the Apple Pencil and for touch under Prefs > Gesture Controls > Assisted Drawing.
Both of these matter for the troubleshooting section below.
Adjust Gesture Controls
If QuickLine feels too slow, too fast, or accidentally triggers while you sketch, change it in the settings:
- Tap the wrench icon (Actions).
- Go to Prefs > Gesture Controls.
- Open the QuickShape section.
- Adjust the hold delay, or turn the feature off entirely.
If you do loose gestural sketching and keep getting snapped lines, a longer delay is better than switching it off. If you do mostly technical work, a shorter delay speeds you up.
Troubleshooting: When Procreate Only Draws Straight Lines
The opposite problem is common too. You draw a curve and get a straight line, or every stroke locks to horizontal or vertical. Work through these in order.
1. Check the Assisted Drawing preference
Go to Actions > Prefs > Gesture Controls > Assisted Drawing. If Apple Pencil is toggled on, turn it off. If Touch is on and you're drawing with a finger, turn that off too. These settings have no effect until you've used a Drawing Guide on the canvas. After that, they can keep constraining your strokes even once you've switched the guide off.
2. Check the layer's Drawing Assist
Open the Layers panel and look at the thumbnail of the layer you're on. If it says "Assisted," tap the thumbnail and toggle Drawing Assist off. This is the culprit when settings look correct everywhere else but a single file keeps locking your lines. It also explains why one layer behaves differently from another.
3. Check the Drawing Guide on the canvas
Open Actions > Canvas. If Drawing Guide is on, turn it off. Or tap Edit Drawing Guide and turn off Assisted Drawing there.
4. Look for the shape notification
If you see the QuickShape notification at the top of the canvas, the behavior is QuickShape. If you don't see it, the cause is something else, most often stabilization.
5. Reset stabilization and smoothing
Heavy stabilization can make strokes look as if they're being pulled in straight segments. Go to Prefs > Pressure and Smoothing and tap Reset. Then test with a few different brushes. A custom brush with its own stabilization set high can cause the same effect, so check the brush settings too. At least one user has reported this behavior appearing after an app update.
If none of that works, restart the app, update Procreate and your iPadOS version, and record a short screen video of the problem. Seeing the behavior makes it much easier for someone to diagnose.
Where Straight Lines Fit in a Motion Pipeline
For motion designers, animators, and compositors, Procreate is often where concepts, boards, and style frames start. Clean linework matters here because whatever you draw becomes a reference for everything downstream. A wobbly horizon line or a slightly rotated panel border gets inherited by every later stage.
A few habits help:
- Lock horizons and frames first. Use QuickLine with 15° snapping for anything that should be level, and put those on their own layer so you can hide or redo them.
- Keep structure and texture separate. Straight geometric elements on one layer, organic hand-drawn detail on another. This makes later changes much less painful.
- Close your shapes. If a shape will be filled, flattened, or isolated, closed paths avoid leaks and ragged edges.
- Export at full size. Whatever you hand off, work at the resolution you'll need so the edges stay sharp.
Quick Reference
Final Thoughts
Straight lines in Procreate come down to one gesture: draw, hold, and add a second finger when you need angle snapping. QuickShape extends that to geometric forms, and the Drawing Guide covers guide-aligned lines. When strokes lock up unexpectedly, the answer is almost always Assisted Drawing in preferences or on the layer, or a stabilization setting that needs a reset. Get those right and you can move quickly between loose sketching and precise structure without leaving the canvas.