How to Get Rid of Hooks in Procreate Brushes
StyleFrame Team8 min read
Hooks in Procreate brushes, the small curls or tails at the start or end of a stroke, usually come from stroke correction fighting your hand motion. The fastest fix is to open the brush in Brush Studio, lower StreamLine and Stabilization, and then check the taper settings. If the hook persists, check your pressure curve and jitter, then rule out iPad accessibility and Palm Support settings. Duplicate the brush before you edit it so you can compare the before and after.
What Causes Hooks at the End of a Stroke
Procreate builds a stroke from many points plotted along the path of your finger or Apple Pencil, then stamps the brush shape along that path. Several settings reshape that path after you draw it:
- StreamLine smooths wobbles and shakes through an Amount slider and a Pressure slider.
- Stabilization takes a moving average of your stroke, so higher values average out more of your movement.
- Taper settings change how the stroke thins at its start and end.
- Jitter and Fall Off add randomness or fade to stamp placement and opacity.
Smoothing means the line you see lags behind your hand. When you lift the pencil, the stroke has to resolve that lag, and the endpoint can swing or curl. Faster strokes and tighter curves make it more obvious.
Hooks can also come from the pen itself. One long-running Procreate support thread describes a "leading tail" of predicted line drawn in front of the cursor that is then corrected as the real line catches up. That produces a flicker as you draw even with StreamLine turned off. So the cause isn't always the setting you expect.
Step 1: Duplicate the Brush Before You Change Anything
Duplicate the brush in the Brush Library. Edit the copy and leave the original alone. If something goes wrong, Brush Studio lets you reset a brush to its default state, but a duplicate gives you a working reference to compare against.
Draw the same test strokes after each change so you know which setting did the work:
- A quick flick
- A slow curve
- A long arc
- A short dash
Step 2: Reduce StreamLine and Stabilization
This is the most common fix.
- Tap the brush to open Brush Studio.
- Go to the Stabilization section.
- Lower StreamLine Amount gradually. Turn it down for more natural linework that is less smooth, or off entirely.
- Lower StreamLine Pressure. A higher Pressure value makes pressure application longer and smoother. A lower value lets pressure kick in more quickly.
- Reduce Stabilization if it is high. Because it averages your movement, it can pull the end of the stroke away from where your hand stopped.
Stabilization can also be set globally in the Accessibility settings, so a global value may be affecting every brush. If hooks show up on every brush you try, check there before editing individual brushes.
The trade-off is that less smoothing returns some of your natural hand wobble. Many artists settle on a low StreamLine value instead of zero, which keeps lines clean without the lag that causes the hook.
Step 3: Rework the Taper Settings
Taper controls how a stroke thins at either end, and a misconfigured taper can leave a thin trailing tail that looks like a hook.
One user in the Procreate support forum found a fix for the predictive-line tail. They modified the default round brush by turning off Classic Taper, then in the stroke taper settings setting the end taper above 25% and pushing pressure to the maximum. They reported this reduced the tail to the point of being unnoticeable. Results vary between devices and Procreate versions, but it is a useful starting point:
- Open Brush Studio and go to the taper settings.
- Turn off Classic Taper if the brush uses it.
- Adjust the end taper in small steps and test after each one.
- If the hook looks like a thin spike, increase the end taper. If the stroke ends too abruptly, reduce it.
Step 4: Check Pressure Curve, Jitter, Spacing, and Fall Off
If the hook is still there, look at the properties that change stamp placement:
- Jitter Linear shifts stamps in the same direction as the stroke. With a high value, even a short stroke produces stamps that extend before and after where you started and stopped. That reads as a small tail or overshoot.
- Jitter Lateral pushes stamps perpendicular to the stroke, which can make a clean end look ragged.
- Spacing Jitter adds randomness to the gaps between stamps. Procreate notes that a high value still changes spacing even if base Spacing is 0%.
- Fall Off fades a stroke as it travels. If it is set high, the stroke end can look wispy.
Set each of these to zero, confirm the hook is gone, then add them back one at a time. Jitter values can also be tied to Apple Pencil pressure and tilt, so check whether a pressure link is adding variation you didn't intend.
Also check your pressure curve. A curve that is too steep or too flat can make lines feel unnatural or run out of ink too early. Part of what looks like a hook may be your pressure dropping off unevenly as you lift.
Step 5: Rule Out System and Input Issues
Sometimes the brush is fine and the input is the problem.
- Zoom in iPad Accessibility. If you use an Apple Pencil, open Settings > General > Accessibility and turn Zoom off if it's on. Procreate's support team points to this setting as a cause of the most recent line being deleted when your hand touches the screen, and it also blocks the three-finger gestures.
- Palm Support. Try both the Standard and Fine settings in the iPad Settings under Procreate. Third-party styluses generally aren't compatible with Palm Support, so a drawing glove may work better.
- Assisted Drawing. If strokes snap to odd angles, go to Actions > Prefs > Gesture Controls > Assisted Drawing and turn off Apple Pencil and Touch. Also check the layer thumbnail for an "Assisted" label.
- Tip Animation and StreamLine on the Stroke tab. Procreate support has suggested checking these when lines lose their final segment or behave oddly.
- Software versions. Note your iPad model, iPadOS version, and Procreate version before you report a persistent issue. Support asks for all three.
Step 6: Adjust Your Technique
Settings only solve part of the problem. Fast flicks at the end of a stroke can create a hook, because the smoothing has to catch up with a rapid change in direction.
- Warm up. Draw ovals, arcs, and crosshatching to loosen your hand before inking.
- Rotate the canvas. Turn it so each stroke follows the natural arc of your wrist instead of forcing an awkward angle.
- Lift cleanly. Finish the stroke at a steady pace and lift straight up rather than flicking away.
- Draw slightly longer strokes. Start a little before the line and end a little after, then erase the excess.
Combining a modest StreamLine value with steady stroke speed gives clean line ends without sacrificing control.
Quick Troubleshooting Checklist
Why This Matters in a Motion Pipeline
For motion designers and animators, hooks are more than a cosmetic problem. Hand-drawn linework, texture strokes, and frame-by-frame animation done in Procreate often end up in After Effects, Nuke, or Blender. A tail on every stroke becomes visible flicker when played back at frame rate, and it is tedious to clean up across dozens of frames. Fixing the brush once, then saving the duplicate as your production brush, keeps your linework consistent from frame to frame.
FAQ
Should I turn StreamLine off completely? Not necessarily. Try lowering it in steps. A small amount keeps lines tidy, and the hook often disappears well before you reach zero.
Why does the hook appear on every brush? Check the global Stabilization settings and the iPad accessibility settings first. Both apply across brushes, and a single brush edit won't fix them.
Will resetting the brush help? It can, if you or a brush pack changed settings you can't identify. Reset restores the brush defaults. If the hook remains after a reset, the cause may be global or hardware-related.
Do third-party brushes cause hooks more often? They can, because custom brushes may ship with high StreamLine, taper, or jitter values. Duplicate the brush and walk through the steps above to find which setting is responsible.