How to Get Procreate to Straighten Lines
StyleFrame Team7 min read
To get Procreate to straighten a line, draw the stroke and hold your Apple Pencil or finger on the screen at the end. QuickShape then snaps the stroke into a clean line, and touching a second finger to the screen locks it to 15° increments. For repeatable straight lines, turn on Drawing Assist with a Drawing Guide. For slightly wobbly freehand strokes, raise Stabilization and StreamLine in the brush settings.
Each method suits a different job, and they stop working in confusing ways when settings collide. This guide covers all of them, plus the fixes for when Procreate straightens everything you draw.
Method 1: Use QuickShape for instant straight lines
QuickShape is the fastest way to get a straight line, and it works with Paint or Erase selected.
- Select a brush and draw a rough line.
- Don't lift your Apple Pencil or finger at the end of the stroke. Hold it still for a moment.
- Procreate snaps the stroke into a straight line. While you're still holding, you can drag to change the line's angle and length.
Lock the angle with a second finger
While the line is held, touch a second finger anywhere on the canvas. The line snaps to 15° increments, which gives you true horizontals, verticals, and 45° diagonals without guessing. The same trick regularizes other shapes: a triangle becomes equilateral, for example.
Edit the shape after it snaps
A notification appears at the top of the canvas right after a QuickShape forms. Tap it to open the edit shape menu, where you can:
- Switch the shape type, such as turning a circle into a square.
- Drag the transformation nodes to adjust the line or shape precisely.
The edit window closes once you move on. If you need to adjust the line later, use the Transform tool instead.
Tune the hold behavior
If lines snap too early or too late, check Actions (wrench) > Prefs > Gesture controls and look at the QuickShape settings. You can adjust the hold delay there, and other trigger options exist. A shorter delay feels snappier, but it can trigger shapes accidentally when you pause mid-stroke.
Method 2: Use Drawing Assist for repeatable straight lines
QuickShape is fast but happens after the fact. If you want every stroke to follow a guide, use Drawing Guides with Drawing Assist.
- Turn on a Drawing Guide and set it up the way you want.
- Open the Layers panel, tap the layer you want to draw on, and enable Drawing Assist.
With Drawing Assist on, your strokes on that layer follow the guide, which makes it useful for technical-looking layouts, UI panels, and storyboard frames.
Drawing Assist is a per-layer setting. A layer showing "Assisted" under its thumbnail has it enabled, and tapping that layer's thumbnail lets you toggle it. That makes it easy to keep one assisted layer for hard-edged structure and another unassisted layer for loose, organic marks.
Method 3: Use Stabilization and StreamLine for freehand lines
Sometimes you don't want a perfectly ruled line. You just want your hand-drawn stroke to be steadier. Procreate has two layers of smoothing for this.
Brush-level stabilization
- Tap the brush icon to open the Brush Library.
- Tap a brush to open Brush Studio.
- Select the Stabilization tab.
- Adjust Stabilization > Amount to smooth and straighten the stroke, and StreamLine > Amount to reduce wobbles and shakes.
StreamLine tends to be the more forgiving option for long curves and inking. Stabilization at higher values makes the stroke lag behind your hand, which suits long straight-ish lines but can feel unresponsive for detail work.
Duplicate a brush before editing it by swiping left on it in the library and tapping Duplicate. If you go too far, open Brush Studio, go to About this Brush, and tap Reset Brush to restore the original settings.
Global stabilization
Under Actions > Prefs > Pressure and Smoothing, a global Stabilization slider applies to every brush. Starting around 10–15% and adjusting from there is a sensible approach. The catch is that it's easy to forget. If your pencil suddenly feels laggy across all brushes, global smoothing is the likely culprit.
When to turn smoothing down
Heavy stabilization removes character. Turn it down or off for gesture drawing, textured marks like fur or frayed edges, sharp corners, and technical details where precision matters more than fluidity.
Method 4: Straighten existing lines with Transform
If you've already drawn something and it's slightly off-angle, you don't need to redraw it.
- Use the Selection tool to select the line, or put it on its own layer.
- Open the Transform tool.
- Rotate it using the nodes.
This is the approach for correcting a horizon line or a panel border after the fact. It rotates and scales the whole selection, though, so it won't fix a line that's curved or wavy. For that, redraw it with QuickShape.
Troubleshooting: Procreate only draws straight lines
The opposite problem is common too: you want freehand strokes, but everything comes out straight or oddly constrained. Work through these checks in order.
- Check Assisted Drawing for Apple Pencil. Go to Actions > Prefs > Gesture controls, tap the Assisted Drawing tab, and see whether the Apple Pencil option is on. Turn it off if it is.
- Check the layer. In the Layers panel, look for "Assisted" beneath the layer name. Tap the layer thumbnail and toggle off Drawing Assist.
- Look for the QuickShape notification. If strokes are snapping, a shape notification and edit button appear at the top of the canvas. If you see neither, it's probably not QuickShape.
- Check stabilization. Extremely high values can make strokes look rigidly straight. Test a few different brushes to see whether it's one brush or all of them, then inspect the global Pressure and Smoothing settings.
- Reset Pressure and Smoothing. In Prefs > Pressure and Smoothing, tap Reset. One user reported that after an app update, smoothing behaved as though it were set beyond maximum, and resetting was the suggested fix.
- Check your QuickShape gesture settings. If you've set draw-and-hold with a very short delay, normal pauses can trigger it.
If none of that works, record a short screen or camera video of the behavior. It makes the problem much easier to diagnose, whether you're posting in a forum or contacting support.
Why straight lines matter when art moves into motion
Many motion designers and animators use Procreate for boards, style frames, and line-art elements that eventually land in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke. Clean lines matter more at that stage than they seem to on a still:
- Scaling and camera moves. A line that's slightly off-axis becomes obvious when it's animated, parallaxed, or pushed in on.
- Alignment across frames. Panel borders, horizons, and architectural edges need to hold their angles from frame to frame.
- Hand-off consistency. Layers with predictable geometry are easier to rig, track against, and composite.
A practical workflow: use Drawing Assist or a grid on a structural layer for hard geometry, use QuickShape for quick corrections, and keep organic line work on separate layers with moderate StreamLine. Export layered files or flattened frames, then import them into your compositing application.
Quick reference
Start with QuickShape for speed, add Drawing Assist when you need consistency, and treat stabilization as a fine-tuning tool rather than a fix for everything. Once you know which setting produces which behavior, you can switch between ruled precision and loose line work without fighting the app.