How to Get Pen Pressure on Procreate
StyleFrame Team7 min read
Procreate gets pen pressure from an Apple Pencil connected to a compatible iPad. Pair the Pencil over Bluetooth and it should work immediately. You then tune the response under Actions → Prefs → Pressure and Smoothing (or Edit Pressure Curve), and per brush in Brush Studio under Apple Pencil → Pressure. If pressure seems dead, the usual fixes are re-pairing the Pencil, resetting the pressure curve, and checking that the brush actually has pressure assigned to size or opacity.
What You Need for Pressure Sensitivity in Procreate
Pressure sensitivity depends on hardware as much as software. Procreate reads pressure from an Apple Pencil on a supported iPad. A finger can't provide pressure data, so it draws at a fixed response no matter how hard you press.
Check three things before changing any settings:
- A compatible Pencil and iPad pairing. The Pencil has to be supported by your iPad model.
- Bluetooth turned on. The Pencil pairs over Bluetooth.
- A brush that responds to pressure. Some brushes have little or no pressure dynamics, so a brush that never changes can look like a hardware fault when it's just the brush.
How to Connect Apple Pencil to Procreate
Procreate has no separate pairing step. You connect the Pencil to the iPad, and Procreate picks it up.
- Swipe down from the top right of the iPad screen to open Control Center.
- Make sure Bluetooth is switched on.
- Attach the Apple Pencil (2nd generation or Pro) to the side of the iPad and wait for the connection dialog. It shows the Pencil's battery level.
Open a canvas and draw a stroke with light pressure, then one with heavy pressure. If the lines differ in size or opacity, pressure is working. If both look the same, check the brush settings below before assuming something is broken.
Adjust the Global Pressure Curve
Procreate has a global pressure curve that sits on top of every brush. Open it from Actions (wrench icon) → Prefs → Pressure and Smoothing, or Edit Pressure Curve in some versions.
The graph maps your physical input to the brush's response:
- The horizontal axis is how hard you press, from no pressure on the left to maximum on the right.
- The vertical axis is how strongly that pressure affects the brush, from no effect at the bottom to full effect at the top.
The default is a straight diagonal line. If light strokes barely show up and you have to press hard to get a mark, make the start of the curve steeper. Tap the line to add a node, then pull it upward. Light pressure then produces a visible mark sooner, which many artists find closer to a real pencil when building mid-tones. Pulling the curve the other way means you need to press harder before anything appears, which suits fewer people.
The sliders at the top of the same menu control stabilization (smoothing) across all brushes. Higher values apply more stabilization to all your brushes.
Procreate's own guidance is to leave global pressure alone unless you have a reason. Its brushes are built to work with the default curve, and aggressive changes can have unwanted effects across your whole brush library. If you make a mess of it, scroll to the bottom of the Pressure and Smoothing menu and tap Reset all, then confirm.
Set Pressure Per Brush in Brush Studio
The global curve is only half of the system. Each brush decides what pressure controls.
- Tap a brush in the Brush Library to open Brush Studio.
- Choose Apple Pencil from the list.
- In the Pressure section, adjust the sliders for Size and Opacity, among others.
Raising the Size slider makes the stroke thicker as you press harder, like a soft-tipped brush. Dragging it into negative values reverses the behavior, so light pressure gives thick lines and heavy pressure gives thin ones. The Opacity slider works the same way for transparency: harder presses give more opaque strokes. Many illustrators drive size with pressure and leave opacity alone, but this is a style choice.
To build a clean test brush, create a new brush with the plus button in the Brush Library, tap Done, and then adjust the Apple Pencil settings from a neutral starting point. That makes it easier to see what each slider does.
Taper
The Taper settings in the same Apple Pencil section control how a stroke thins at its start and end. Pressure handles the thick-to-thin dynamics in the middle of a stroke, and taper shapes the entry and exit so the line feels more like a real brush tip. You can link the start and end tapers or edit them separately. Longer taper distances give smoother transitions.
Troubleshooting: Pressure Not Working in Procreate
A frequent complaint is a Pencil that's recognized and draws, but needs a hard press before a mark appears. Work through these in order, starting with the cheapest fixes.
- Check the sidebar opacity slider. If it has slipped down, strokes look faint regardless of pressure.
- Test a few brushes. If the problem only affects brushes with opacity tied to pressure, the issue is likely the brush's pressure settings or the curve rather than the hardware.
- Reset the pressure curve. Go to Actions → Prefs → Pressure and Smoothing and tap Reset all.
- Reset gesture controls. Actions → Prefs → Gesture Controls → General → Reset to Defaults. It's a less obvious fix, but it's on Procreate's troubleshooting path.
- Restart the iPad and re-pair the Pencil. Reboot, then attach the Pencil to reconnect it.
- Test with a plain brush. Create a new canvas, pick a dark color, choose a basic painting brush, push the sidebar sliders up, and see whether the Pencil responds.
- Try another Pencil. Procreate makes greater demands on the Pencil's pressure and tilt sensing than many apps do. A Pencil can seem fine in Notes and still have a sensor problem that only shows in Procreate. Borrowing a second Pencil, or having Apple test yours on your iPad, separates a hardware fault from a settings problem.
If a reboot fixes things only for a few minutes before pressure fails again, that points to a deeper issue and is worth taking to Apple, especially if the Pencil is under warranty.
Pressure on iPhone and Procreate Pocket
Procreate Pocket, the iPhone version, doesn't offer Apple Pencil pressure sensitivity. Users get a similar effect by changing brush size or opacity manually while painting. If pressure-sensitive drawing is central to your work, that's a reason to do it on an iPad.
Using Pressure-Sensitive Procreate Work in a Motion Pipeline
If you work in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, you may be using Procreate for storyboard panels, style frames, character designs, or hand-drawn texture and linework. Pressure-sensitive strokes carry weight and variation that flat vector shapes lack, and that character shows up on screen when the art moves.
Dialing in pressure before a project helps, since line quality across a set of frames depends on consistent settings. Fix the brush and curve first, then draw. Changing the curve halfway through a board set can make stroke weight drift between panels.
Quick Reference
Frequently Asked Questions
Why is my Apple Pencil not showing pressure in Procreate?
Start with the brush. If its Size and Opacity pressure sliders are at zero, the Pencil will draw without variation. Then reset the pressure curve, restart the iPad, and re-pair the Pencil. If another Pencil works on the same iPad, the first one may have a hardware issue.
Should I change the global pressure curve?
Only if the default feels wrong, such as needing to press too hard for a visible mark. Procreate's brushes are designed around the default, so make small adjustments and know that Reset all restores the original behavior.
Can I get pressure sensitivity with a finger or non-Apple stylus?
A finger can't provide pressure data. Some third-party styluses may offer limited support, but results depend on the stylus and iPad, so check compatibility before buying one.
Does pressure work the same in every brush?
No. Each brush defines its own pressure response in Brush Studio, and the global curve sits on top of that. Two brushes can feel completely different under the same curve.