How to Flood Fill in Procreate
StyleFrame Team7 min read
To flood fill in Procreate, drag a color from the Colors icon in the top right onto a closed shape, hold for a moment, and slide left or right to set the threshold before you lift. Tap Continue Filling afterward to fill more areas with single taps. If the color floods the whole canvas, lower the threshold or check whether any layer is set as a Reference layer.
Procreate calls its flood fill ColorDrop. It is one of several fill methods, and each suits a different job.
Flood fill with ColorDrop
ColorDrop works like a paint bucket you drag into place:
- Pick your color in the Colors icon at the top right.
- Drag that icon onto the area you want to fill, and keep your Apple Pencil or finger down.
- Without lifting, slide left or right. A percentage appears at the top of the screen. Left fills less, right fills more.
- Lift to commit the fill.
The threshold controls how aggressively the color fills. A low value fills less and stays tight to the area where you dropped. A high value fills more, and at 100% it can flood the entire screen. Procreate remembers your threshold setting until you adjust it again.
For clean line art on a transparent background, a moderate threshold usually fills the enclosed shape up to the line. Soft or textured brushes and anti-aliased edges often need a higher value to reach the edge of the stroke, which is a trade-off covered in the fringe section below.
Keep filling with Continue Filling
After a ColorDrop, Procreate offers Continue Filling. Tap it and every subsequent tap on the canvas fills with the current color, so you can flat many shapes quickly. You can also tap and hold, then drag, to adjust the threshold mid-session.
To leave this mode, tap the checkmark at the top or switch to another tool such as Paint.
If your iPad and Pencil support hover, you can hover over the current color swatch and double-tap the Pencil's side to jump straight into Continue Filling with that color. It saves a trip through the interface when you are working through dozens of shapes.
Fill on a separate layer with a Reference layer
A common flatting setup keeps line art on one layer and color on another. By default, ColorDrop samples the layer you are painting on, so if the line art sits elsewhere, the fill will flood the empty layer and cover everything. The fix is a Reference layer:
- Open the Layers panel.
- Tap the thumbnail of your line art layer.
- Choose Reference in the Layer Options menu.
- Select a new layer beneath it and ColorDrop into that layer.
ColorDrop now reads the line art for boundaries and puts the color on the layer you selected. This is the right setup for animation backgrounds, character flats, and anything you want to revise later without touching the ink.
The same trick gives you fill opacity. Procreate's fill doesn't take its own opacity setting, but if you drop the color onto a separate layer you can adjust that layer's opacity and blend mode afterward. Merge the layers when you are done, and the settings are preserved.
Other ways to fill an area
ColorDrop is the fastest method, but not the only one.
Recolor
Recolor is an older fill mode that is hidden unless you turn on QuickMenu. Go to Actions → Prefs → Gesture Controls → QuickMenu and choose how you want to invoke it. Then assign Recolor to one of the radial options. Once in Recolor mode, pick a color, tap the areas you want to fill, and use the Flood slider to control how far each fill spreads. It behaves like ColorDrop, but some artists prefer the tap-first, tune-later rhythm.
Color Fill with Selections
Selections can fill automatically as soon as you complete them:
- Tap Selections at the top.
- Choose a method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Turn on Color Fill so it is highlighted blue.
- Choose a color and make your selection.
The area fills as soon as the selection closes. This is useful when you want a precise shape instead of a boundary-detected region, such as a geometric background panel or an ellipse for a glow. You can soften the edges with Selections → Feather.
Two cautions. Color Fill stays on even if you exit and re-enter Selections, so switch it off when you are finished or you will fill things by accident. It also only works on a single layer, not on a group.
Fill Layer
To fill an entire layer, select your color, open Layers, tap the layer, and choose Fill Layer in Layer Options. This works well for solid background plates, flat mattes, and base layers you intend to clip other layers onto.
Troubleshooting flood fill problems
Most fill problems fall into a few patterns.
The color fills the whole screen. Check these in order:
- Threshold too high. Drag the color in, pause, and slide left while still touching the screen. Lower it until the fill stays inside the shape.
- A stray Reference layer. Users report that a layer set as Reference anywhere in the document, even inside a different group, can cause this. Open Layers and turn off Reference on layers you no longer need.
- Unmerged line layers. If your outlines are split across several layers, the boundary may be incomplete. Some users fixed the problem by merging the outlines into one layer.
- A gap in the line. An opening in the line can let the fill leak.
The threshold slider does nothing. Some users who saw this found that turning off Reference on another layer fixed it. Check your layer settings before resetting anything else.
ColorDrop does not pick up the color at all. Some users have reported intermittent failures, particularly when filling a layer that was already filled with another color. Some users say restarting the app clears it. If it persists, update Procreate and iPadOS and contact Procreate support with your device and version details.
Limits to plan around: gaps and fringes
Procreate's flood fill has no gap-closing setting. Some other painting and inking apps let you specify how large a gap in your line the fill can bridge, but ColorDrop treats an open line as an open line. Close gaps by hand with a hard brush on the line layer before you fill.
Anti-aliasing is the other limit. Soft edges mean the pixels along a line are partially transparent, and a fill at a low threshold may stop short of them. That can leave a pale halo between the line and the color. There are two common ways to deal with it:
- Raise the threshold slightly so the fill tucks under the edge of the line. Because the color is on a separate layer beneath the line art, the overlap is hidden.
- Fill on a layer under the line art, then check the result at 100% zoom or higher before you export.
If your work depends on perfectly hard-edged fills, such as strict cel-style flats for compositing, test a small sample before committing to a full scene. Procreate can do it, but it takes more care than dedicated flatting tools.
Using flood-filled art in a motion pipeline
Flats made in Procreate can feed into motion work in a few ways. The simplest is to export layered files and bring them into a compositing, editing, or 3D tool. Keeping line art, flats, and shadows on separate layers lets you animate, recolor, or parallax them in compositing instead of baking everything into one flat image. A clean, separate color layer also makes a usable matte for grading or stylized effects.
Name your layers and keep each region of color on a predictable layer before export. It takes seconds in Procreate and saves a lot of cleanup when the file lands in a comp.
Where Styleframe fits after the flat colors are done
Once the flats are in place, you may want to carry that look through moving footage or across a sequence of frames. is one option to look at for that step. Procreate remains where you do the hand-drawn work.
Quick reference
- Fast fill: drag the color in, hold, slide to set the threshold, then lift.
- Many shapes: tap Continue Filling.
- Flats separate from ink: set the line art layer to Reference and fill on a layer below.
- Fill with opacity: drop color on its own layer and adjust the layer.
- Geometric shapes: use Selections with Color Fill.
- Whole layer: use Fill Layer.
- Whole canvas floods: lower the threshold, then check for stray Reference layers and gaps in the line.