How to Find Streamline in Procreate
StyleFrame Team6 min read
In Procreate, StreamLine is a per-brush setting inside Brush Studio. Open the Brush Library, select a brush, tap it again to open Brush Studio, choose Stroke Path (the Stroke tab in Procreate Pocket), and use the StreamLine Amount and Pressure sliders. It is separate from Stabilization, which sits in the same area and can also be set globally under Accessibility in the Gestures settings.
Where to Find StreamLine in Procreate (iPad)
StreamLine is not a global toolbar toggle. It belongs to each brush, so you reach it through the brush's settings:
- Tap the Brush icon in the top-right toolbar to open the Brush Library.
- Tap the brush you want to adjust so it is selected.
- Tap the selected brush again to open Brush Studio.
- In the left-hand list of attributes, tap Stroke Path.
- Find the StreamLine section. It contains two sliders: Amount and Pressure.
The Stroke Path panel also holds Spacing, Jitter, and Fall Off, so you are in the right place if you see those. Drag a slider, then scribble on the drawing pad in Brush Studio to see the effect before you go back to the canvas. Tap Done when you're happy.
One practical habit: duplicate a brush before editing it. Swipe left on the brush in the library and choose Duplicate, then change StreamLine on the copy. That way your original brush stays intact, and you can keep a "clean ink" version and a "loose sketch" version side by side.
Finding StreamLine in Procreate Pocket
The iPhone version organizes things slightly differently. Open your canvas, select the brush, and tap the brush icon in the top menu to reach its settings. Then open the Stroke tab, where the Streamline slider lives. Slide right to increase smoothing.
Interface labels shift between versions, so if your menu looks a little different, look for the Stroke or Stroke Path area first. StreamLine is grouped with the other stroke behavior controls.
What the StreamLine Sliders Actually Do
Procreate builds a stroke from many points plotted along the path of your finger or Apple Pencil. StreamLine smooths wobbles and shakes in that path, which is why it matters most for inking and calligraphy.
- Amount: Higher values produce smoother, more even lines. Lower values or off give more natural, less corrected linework.
- Pressure: Higher values make the pressure response build over a longer, smoother distance. Lower values or off make pressure kick in more quickly as you press.
Amount controls how much the line is smoothed. Pressure controls how pressure is applied along the stroke. If your lines look smooth but the tapers feel sluggish, check Pressure before you reduce Amount.
StreamLine vs. Stabilization
Both settings live under the stroke controls and both smooth your line, but they work differently. Procreate's documentation describes Stabilization as taking a moving average of your stroke and drawing that on the canvas. The higher the value, the more the wobbles get averaged out, and the more deliberate and straight the stroke becomes.
StreamLine, by contrast, assists in smoothing out wobbles or shakes in your line as you draw it. In practice:
- Use StreamLine when you want confident, flowing curves for ink lines, lettering, or character outlines.
- Use Stabilization when you want strokes that feel deliberate and straight, such as technical shapes, hard-surface outlines, or long clean edges.
- Stabilization can be set globally if you need consistent behavior across every brush. StreamLine is configured brush by brush.
Combining a modest amount of each can work better than pushing one slider to the maximum.
Recommended StreamLine Values
There is no universal setting, but a few starting points help:
- Sketching and roughs: Off or very low. You want the energy and irregularity of your hand.
- Inking and clean line art: One published Procreate Pocket guide suggests about 30–40% as a balance between control and flexibility. Treat that as a starting point, not a rule.
- Lettering and calligraphy: Moderate to higher values, since smooth curves matter more than raw gesture.
Pushing StreamLine very high can make lines feel elastic or automated. If your strokes feel like they're being dragged through syrup, back off. A little goes a long way.
Why StreamLine Feels Like It's Still On at 0
Some users on Procreate's forums complained that lines still seem corrected even with StreamLine at 0%. Procreate's response in that thread was that no StreamLine is applied when the slider is set to None, and that what users noticed was likely the newer handling of Apple Pencil's predictive strokes. That thread dates from an older version, so behavior may have changed since.
If you're troubleshooting something similar:
- Check that the brush you're using has StreamLine at 0, not just another brush.
- Check Stabilization on the same brush and in the global Accessibility settings. It may be the source of the smoothing you're feeling.
- Test on the Brush Studio drawing pad with a default brush to see whether it's brush-specific.
- Note whether the issue is smoothing or something else, like lines curving or stroke ends vanishing. Those have been reported separately and may be unrelated to StreamLine.
Why This Matters for Motion and VFX Work
If you're an animator or motion designer, you probably use Procreate for the hand-drawn parts of a pipeline: frame-by-frame character beats, ink overlays, rotoscope-style cleanup, boards, or textured elements you'll composite later. Consistent line quality matters more in motion than in a single illustration. Stroke wobble that looks charming in a static piece can read as unwanted jitter when drawings play back at 12 or 24 frames per second.
A few habits help:
- Pick one inking brush and lock its settings before starting a sequence. Changing StreamLine mid-shot makes line character drift between frames.
- Save a duplicate per use. One "boil-friendly" loose-ink brush and one "clean-lock" brush give you intentional choices rather than accidental ones.
- Test in motion early. Export a few frames, bring them into After Effects, and play them back before drawing the whole sequence.
- Export with transparency where possible so your linework can be composited over backgrounds, plates, or 3D renders in After Effects, Nuke, or Blender.
Quick Reference
Where is StreamLine in Procreate? Brush Library → select a brush → tap again to open Brush Studio → Stroke Path → StreamLine. In Procreate Pocket, look under the Stroke tab in brush settings.
What are the two StreamLine controls? Amount (overall smoothing) and Pressure (how smoothly pressure response builds).
Does StreamLine apply to every brush? No. It's set per brush, so changing one brush doesn't affect the others.
What's a good starting value? Low or off for sketching, and around 30–40% for clean inking as a starting point, adjusted by feel.
What if lines still look smoothed at 0? Check Stabilization on the brush and in global settings, and test with a default brush to isolate the cause.
Can I use StreamLine and Stabilization together? Yes. Moderate amounts of each often work better than maxing out one.
Once you know that StreamLine lives in Brush Studio under Stroke Path, it becomes a setting you can tune per brush and per project instead of something you stumble across. Set it deliberately, save duplicates of the brushes you rely on, and test a few frames in motion before committing to a full sequence.