How to Fill Outline in Procreate
StyleFrame Team8 min read
To fill an outline in Procreate, drag the Colors icon from the top right into a closed shape (ColorDrop), and before lifting your Apple Pencil, slide left or right to set the threshold so the fill reaches the line edges. For cleaner production work, mark your line layer as a Reference layer and drop color onto a separate layer beneath it, so the fill never touches your linework. If color leaks into the rest of the canvas, there is almost always a gap in the line that needs closing first.
Before You Fill: Prep the Outline
Most fill problems start with the line art, not the tool. A few minutes of setup saves a lot of cleanup.
- Keep linework on its own layer. If strokes are spread across several layers, group them, duplicate the group, and merge the duplicate into one flattened line layer. Keep the original group untouched.
- Check for gaps. Zoom in on corners and joins. Even a very small gap can be enough for ColorDrop to flood out of the shape.
- Create separate layers for fills. Putting each color region on its own layer lets you adjust, recolor, or hide regions later without repainting.
- Pick the right brush for line work. Hard-edged lines give ColorDrop a clearer boundary to work against than very soft or textured strokes.
Method 1: ColorDrop with Threshold
ColorDrop is the fastest way to fill a closed outline. It works like a paint bucket you drag into place.
- Select the layer you want to fill (ideally a new layer below the outline, or the same layer as the line if you want a quick fill).
- Drag the Colors icon in the top right into the shape and keep holding.
- While still holding, slide left or right to change the ColorDrop Threshold. The percentage appears at the top of the screen. Left fills less; right fills more.
- Lift the pencil or finger to commit the fill.
After a drop, tap Continue Filling to fill other areas with simple taps. You can also tap and hold to adjust the threshold on any individual fill. Tap the tick, or switch to another tool like Paint, to leave that mode.
On iPads that support Apple Pencil hover, you can hover over the current color swatch and double-tap the side of the Pencil to jump straight into Continue Filling with that color.
A low threshold leaves a thin unfilled rim along anti-aliased line edges. A high threshold pushes the fill past the line and into neighboring areas. The goal is the lowest value that covers the soft edge of the stroke without escaping.
Method 2: Reference Layer for Fast, Clean Fills
If you're coloring a full illustration, the Reference layer approach is the one to learn. It lets you fill on layers that don't contain the outline at all.
- Tap the outline layer's thumbnail and choose Reference.
- Create a new layer beneath the outline (for example, "skin").
- Drag a color into the shape. Procreate uses the reference layer to detect the boundaries, but paints onto the layer you've selected.
- Make another layer for the next region (hair, clothing, background) and repeat.
The result is a stack of flat-color layers that each correspond to one part of the artwork, with the line layer sitting on top. That stack is far more useful downstream than a single flattened image, because every region can be selected, recolored, or masked independently. Turning the outline off reveals the separate color layers, which also work as ready-made masks.
Method 3: Selections with Color Fill
Selections offer another route when ColorDrop is unpredictable.
- Tap Selections and pick a method from the bottom tabs (Automatic, Freehand, Rectangle, Ellipse).
- Tap Color Fill so it's highlighted blue.
- Choose your color from the Colors icon.
- Make the selection. The color fills as soon as the selection completes.
Two caveats: Color Fill works on a single layer, not a group, and the setting is remembered even if you exit and re-enter Selections, so turn it off when you're done or you'll fill things by accident later.
Automatic Selection is useful here because you can tap inside a shape, then drag to adjust its threshold, similar to ColorDrop but with a visible selection you can modify, feather, or add to.
Method 4: Fill Layer and Alpha Lock
Two other tools handle cases where you want to recolor an entire shape rather than flood a region.
- Fill Layer: Choose a color, open the Layers panel, tap the layer, and pick Fill Layer from the options. This floods the whole layer with the current color. It's most useful on a layer that already has a selection active, or when filling a full-canvas background.
- Alpha Lock: Tap the layer thumbnail and choose Alpha Lock. Painting is then restricted to pixels that already have content. This is how you recolor a line layer or apply a gradient or texture to a silhouette without spilling outside the shape.
Fixing the Common Problems
Color leaks out of the shape
This means the outline has a gap. Zoom in and close it with a brush on the line layer. If you can't find it, lower the threshold or try an Automatic Selection to see where the selection spreads. As a stopgap, you can paint a temporary closing stroke on a separate layer, fill, then delete the stroke.
White fringes or hairlines between fills
When you hide the outline, thin bright seams often show between adjacent color regions, because the fill stopped at the edge of the anti-aliased line. Several fixes work:
- Alpha Lock the line layer. Unhide the outlines, turn on Alpha Lock, and paint over the lines with the colors of the adjacent fills. The lines now take on the region colors, so there's no seam.
- Fill under the lines. Use Automatic Selection on the area outside your character, invert the selection, and fill a new layer with a solid color. That color extends underneath the lines. Then close any gaps and use Color Fill or ColorDrop to recolor individual regions on that layer.
- Draw the edge in the fill color. Trace the boundary of each color block in that color, then ColorDrop on the same layer so the fill merges with the edge.
- Skip outlines for some regions. Painting color blocks directly, using the line art only as a tracing guide, avoids the problem entirely.
The fill looks jagged
Raise the threshold slightly so the fill covers the soft edge pixels, or use a selection and apply a small feather before filling. Working at a higher canvas resolution also helps when the art will be scaled up.
If You Meant Adding an Outline Around Art
Some people searching this phrase want to add an outline (like a sticker border) around an element, not fill an existing one. A reliable method:
- Hide the background so you can see the result on a dark canvas.
- Duplicate the artwork layer.
- On the duplicate, open Adjustments → Hue, Saturation, Brightness. Set brightness to 100% and saturation to 0%, which turns the layer solid white.
- Move the white layer beneath the original.
- Apply Adjustments → Gaussian Blur to the white layer, starting around 10 to 12%, to grow the edge.
- Use Selections → Automatic with Add, tap the white layer, then drag to adjust the threshold and tighten or widen the border. Fill the selection with white on a new layer.
Adjust the blur and threshold to taste. Smaller values give a thin border; larger values give a heavier, more rounded edge.
Taking Procreate Fills into a Motion Pipeline
For motion designers, animators, and compositors, a well-organized fill setup matters more than the fill itself. A few habits make Procreate art easier to use in After Effects, Nuke, or Blender:
- Name your layers by region and keep line art separate. Flat color layers beneath a line layer are far easier to animate, matte, or recolor in a compositor.
- Close shapes completely. Clean, closed regions make it easier to build mattes or isolate elements later.
- Work at the final delivery resolution or larger. Upscaling flat illustration late in the process can soften edges.
- Keep a flattened reference version. Export it alongside your layered file as a look target for any later work.
Quick Reference
Final Tips
Start with closed, single-layer linework, use the Reference layer for anything with more than a few regions, and keep each color region on its own layer. When a fill misbehaves, check for gaps and threshold before anything else. With that structure in place, your Procreate art is easy to edit, and ready to hand off to the rest of your motion pipeline.