How to Fill on Procreate
StyleFrame Team8 min read
To fill an area in Procreate, pick a color and drag it from the Colors icon in the top right into a closed shape. This is ColorDrop. Keep your Apple Pencil or finger on the screen after dropping and slide left or right to change the Threshold. Lower values fill less and higher values push the fill further into gaps and edges. For more control, use Selections → Color Fill, Fill Layer, or Alpha Lock to fill an entire layer or only its painted pixels.
The fastest method: ColorDrop
ColorDrop works like a bucket tool. It floods the area you drop onto and stops when it hits an outline or a different color.
- Choose your color in the Colors panel.
- Drag the Colors icon (or a swatch from a palette) onto the area you want to fill.
- Lift to commit, or keep holding to adjust the Threshold first.
You can also drag from a swatch in an open palette. That is useful when your fill color differs from the color you drew the outline with, because you don't have to keep changing your active color.
Adjust the ColorDrop Threshold
Holding after the drop shows a thin blue bar and a percentage at the top of the canvas. Slide left to fill less and right to fill more. Release when the fill looks right.
Procreate remembers your last Threshold. If a new fill looks too loose or too tight, the cause is probably the leftover value from your previous fill. Check the percentage before you assume something is broken.
Keep filling with Continue Filling
After a ColorDrop, tap Continue Filling to keep filling other areas with single taps. You can still tap, hold, and drag to change the Threshold on any of them. Tap the tick at the top, or switch to another tool such as Paint, to leave the mode.
If your iPad and Apple Pencil support hover, you can hover over the active color in the top right and double tap the side of the Pencil to start Continue Filling with that color.
Fill with Selections → Color Fill
Selections → Color Fill fills an area the moment you finish a selection, so you don't need a separate fill step. It suits hard-edged shapes, flat color blocking, and anything you want to define precisely.
- Tap Selections at the top.
- Choose a selection mode from the tabs at the bottom: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Pick your color from the Colors icon.
- Make your selection. The area fills when you finish it.
Two things catch people out:
- Color Fill stays on. Procreate remembers the setting, even after you leave and re-enter Selections. Turn it off when you're done, or your next selection will fill unexpectedly.
- It works on one layer only. You can't Color Fill onto a group, so select an individual layer first.
Combining Color Fill with Feather gives you a soft-edged fill, which is handy for vignettes or for framing artwork with a color wash.
Fill an entire layer
To flood a whole layer with one color:
- Select your color.
- Open the Layers panel and tap the layer you want.
- In the Layer Options menu, tap Fill Layer.
This replaces everything on that layer with the solid color. It works well for backgrounds, and for building a base layer you intend to mask or clip later. If the layer already has artwork you want to keep, duplicate it first or use Alpha Lock instead.
Recolor: the older alternative
Recolor is an older feature that Procreate removed and later brought back. It is available only through QuickMenu, which is off by default.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and turn on your preferred trigger.
- Set one of the QuickMenu radial options to Recolor.
- Choose a color, tap the areas you want to fill, and use the Flood slider to control how aggressively it spreads.
Most people are fine with ColorDrop and Continue Filling. Recolor appeals if you like the tap-and-adjust workflow of a flood slider.
Fill shapes with gradients and patterns
Solid fills are only part of it. Two layer-based techniques cover most of the rest.
Alpha Lock for gradients and textures
Alpha Lock restricts painting to pixels that already exist on a layer, so your shape acts as its own mask.
- Draw or import your shape on its own layer.
- Tap the layer and choose Alpha Lock.
- Paint, smudge, or drag a gradient across the layer. Color only lands inside the shape.
This is the cleanest route for lettering, icons, and silhouettes, because your edges stay intact however loosely you paint.
Lighten blend mode
Fill the shape with black on one layer. Add a new layer above it containing a gradient, then change that layer's blend mode to Lighten. The gradient only shows where the layer below is darker than it, so it appears within the black shape. It's an unusual approach, but it keeps the gradient on a separate layer you can edit.
Clipping masks for patterns
Put your shape on a base layer. Add a pattern or texture layer above it and choose Clipping Mask. The pattern shows only within the shape below, and you can move or scale it without touching the shape.
Why your fill isn't working
Most Procreate fill problems come down to a handful of causes.
The color flooded the whole canvas. Your outline has a gap. ColorDrop escapes through any opening, so a shape that isn't fully closed fills everything. Undo with a two-finger tap, close the gap with a brush stroke, and try again.
The fill leaves gaps or halos along the edge. This usually happens with textured brushes such as chalk. Grain creates thin, uneven pixels along the outline that ColorDrop treats as gaps. Raise the Threshold slowly, a percentage point at a time, until the gaps close. Expect some mismatch between a solid fill and a textured line. For clean results, draw the outline with a solid brush such as a monoline, or put the fill on a separate layer under the line art.
The fill ignores a different layer's lines. If your line art sits on another layer, the fill may not respect it. Try filling on the line-art layer itself. Pre-filling closed shapes with a flat color on the line layer also works.
Color Fill is filling things I didn't intend. The setting is still on from your last Selections session. Turn it off.
The fill looks too tight or too loose. Check the remembered Threshold from your last fill and reset it.
A clean fill workflow for production art
If your Procreate art is headed for animation, tidy layers matter more than speed. A structure that survives handoff:
- Line art on its own layer, using a solid brush so ColorDrop behaves.
- Flat color fills on a layer below, so you can adjust or swap them without redrawing.
- Shading and texture on Alpha Locked or clipped layers above.
- A background layer filled with Fill Layer, kept separate from characters and props.
Clear layer separation gives you something to export, composite, and revise later, whether you're building a storyboard, a style frame, or character art.
Where Procreate fills fit in a motion pipeline
Procreate is built for hand-drawn illustration, and it can be used to create style frames, character designs, and texture sources before moving into other tools. Fills are the fast part. The harder question is how to turn a few well-drawn frames into motion without redrawing every in-between.
This is where can sit alongside your Procreate work. It is an AI video and motion tool, and illustrated source art like your flat-filled Procreate frames can serve as reference material. Check the Styleframe site for its current features and supported workflows.
Cleaner Procreate files make better reference art in any pipeline. Closed shapes, solid fills, and separated layers are easier to work with than rough, half-filled art.
Quick reference: which fill method to use
Final tips
- Close your outlines before filling. Most failures trace back to a gap.
- Watch the Threshold percentage, since Procreate remembers the last value.
- Keep fills and line art on separate layers so edits stay easy.
- Turn off Color Fill when you finish with Selections.
- Use Alpha Lock or clipping masks when you want edits that don't touch your original shape.
Once ColorDrop, Color Fill, and Alpha Lock are second nature, filling stops being the slow part of an illustration. You'll spend your time on the design, and on getting the art into motion.