How to Fill on a Different Layer Procreate
StyleFrame Team6 min read
To fill on a different layer in Procreate, set your line art layer as the Reference layer, then select the layer you want to color and drag a color into the area with ColorDrop. Reference tells Procreate to read the shapes from the line art while placing the fill on whichever layer is active. Without a Reference layer, ColorDrop reads only the active layer, which is why a fill on an empty layer floods the entire canvas.
Why ColorDrop fills the whole canvas on a new layer
ColorDrop works by detecting the edges of the pixels on the layer you're working on. A new layer under your line art is empty, so there are no edges to detect and the fill spreads everywhere.
Reference changes where Procreate looks. Once a layer is marked as Reference, ColorDrop reads its contents no matter which layer is active. The line art stays put, and your color lands on a separate layer beneath it.
Step-by-step: fill on a different layer with a Reference layer
- Separate your line art. Keep the outlines on their own layer, usually at the top of the stack. Create at least one empty layer below it for color.
- Set the Reference layer. Open the Layers panel, tap the line art layer's thumbnail to open Layer Options, and tap Reference. A check mark appears beside the option, and the word "Reference" shows on the thumbnail.
- Select the target layer. Tap the empty layer where you want the color to go.
- Drag a color in. Drag the color swatch from the top-right corner into an enclosed area of the line art. The fill is written to the active layer, shaped by the Reference.
- Adjust the threshold. Keep your finger or Apple Pencil down after dropping the color, then slide left or right. The percentage shown at the top of the canvas controls how aggressively the fill spreads. Lift to commit.
For many areas in a row, tap Continue Filling after the first drop. You can then tap each region to fill it, or tap and hold to adjust the threshold as you go. Tap the checkmark or switch tools to exit.
Organizing fills across multiple layers
The real advantage of Reference is that you can build a layered color structure without touching your line art:
- Create one layer for skin, one for hair, one for clothing, and one for background.
- Keep the line art marked as Reference and switch layers between fills.
- Hide the line art at any time and you have clean, separate color shapes you can select, adjust, or hand off.
Because each color zone sits on its own layer, later edits are cheap. You can recolor or adjust one region without repainting the others.
Alternative method: Automatic Selection plus Fill Layer
If ColorDrop gives you uneven edges, you can fill through a selection instead. This also respects the Reference layer.
- Keep the line art set as Reference.
- Choose the Selection tool and use the Automatic mode.
- Tap inside the area you want. Tap other areas to add them to the selection.
- Switch to your color layer.
- Open Layer Options for that layer and tap Fill Layer.
Fill Layer uses your current color.
Color Fill in Selections
Selections also has a Color Fill toggle. When it's on, any selection you finish is immediately filled with your current color on the active layer. It's fast for rectangles, ellipses, and freehand shapes. Note that Color Fill works on a single layer only, not on a group, so select an actual layer inside the group rather than the group itself. Turn it off when you're done, since Procreate remembers the setting between sessions.
Recolor via QuickMenu
Recolor is an older fill method that's still available through QuickMenu. It's off by default. Enable it under Actions → Prefs → Gesture Controls → QuickMenu, assign Recolor to one of the radial options, and then tap areas to fill them. A Flood slider sets how aggressive the fill is. It's a reasonable fallback if you prefer tapping to dragging.
Troubleshooting common problems
The fill still floods the whole canvas. Check that Reference is actually active on the line art layer. You should see the word on its thumbnail. Also confirm you're dropping the color inside a closed shape.
Color leaks outside the shape. A small gap in the line art lets the fill escape. Close the gap on the line art layer, or lower the threshold so the fill stops short of the opening.
Color stops short of the line, leaving a halo. The threshold is too low for anti-aliased edges. Raise it slightly while the fill is still active. Another common practice is to fill slightly beyond the line and let the line art layer on top cover the overlap.
Only one line layer works. Procreate supports one Reference layer at a time. If your lines are split across multiple layers, you'll need to merge copies of them into one layer (duplicate first, so your originals are preserved) and set that merged copy as Reference. Users have asked Procreate for a fill tool that reads from multiple layers, but the single-Reference limit is how it works at the time of writing.
The fill lands on the wrong layer. ColorDrop writes to the active layer, so check the selected layer before you drop.
Taking layered Procreate art into a motion pipeline
If you're a motion designer or compositor, the reason to fill on separate layers is usually downstream. Flat color on its own layer is easy to isolate, matte, and animate. A few habits help when the artwork heads to After Effects or another compositor:
- Name layers before export. "Skin_base," "Hair_base," and "Lines" are far easier to work with than "Layer 14."
- Keep line art separate from color. This lets you animate or restyle them independently, for example by adding boil to the lines while the color stays stable.
- Fill slightly under the lines. Overlap prevents hairline gaps when layers move relative to one another.
- Check your canvas size. Export at a resolution that will survive your delivery format, since scaling flat art after the fact is rarely as clean as drawing it at size.
Quick reference
Summary
Filling on a different layer in Procreate comes down to one setting: mark the line art layer as Reference, select the layer you want to color, and use ColorDrop or an Automatic Selection with Fill Layer. Adjust the threshold to manage edge coverage, keep your line art in one layer because only one Reference can be active, and name your layers if the file is headed for After Effects or another compositing tool. With color separated cleanly from line, the artwork is much easier to animate, restyle, or extend into motion.