How to Fill Object with Color in Procreate
StyleFrame Team7 min read
To fill an object with color in Procreate, pick your color, drag the Active Color dot from the top right into a closed shape, and release. This is ColorDrop. Keep your Apple Pencil or finger down after the color floods in and slide left or right to change the ColorDrop Threshold, which controls how far the fill spreads toward the edges. For more control, use Selections → Color Fill, Alpha Lock, Fill Layer, or a Reference layer.
Method 1: ColorDrop (the fastest fill)
ColorDrop works like a paint bucket you drag into place.
- Tap the colored dot in the top right to choose your Active Color, or pull a swatch from a palette.
- Press and drag the color into the shape you want to fill.
- Keep holding. A blue Threshold bar appears with a percentage.
- Slide left to fill less, or right to fill more.
- Lift to commit.
The fill spreads outward from where you drop it and stops at borders or at a different color. It works best on closed shapes with clean edges.
Continue Filling
After a ColorDrop, a Continue Filling option appears at the top of the screen. Tap it and you can fill other areas with single taps, or tap-and-drag to adjust the threshold on each one. Tap the checkmark or switch to another tool to exit. This is useful when you're flatting a whole character or a set of shapes in one color.
If your iPad and Apple Pencil support hover, you can hover over the Active Color and double-tap the Pencil to jump straight into Continue Filling.
Method 2: Recolor
Recolor is an alternative to ColorDrop that you reach through QuickMenu, which is off by default. To enable it, go to Actions → Prefs → Gesture Controls → QuickMenu and choose how you want to trigger it. Then:
- Assign Recolor to one of the QuickMenu radial slots and tap it.
- Choose your color.
- Tap the areas you want to fill.
- Use the Flood slider to control how aggressively the color spreads.
Recolor suits artists who like tapping to fill. Some also find the Flood slider easier to dial in than dragging a threshold mid-gesture.
Method 3: Selections with Color Fill
Selections give you the most deliberate control, because the fill is limited to exactly what you select.
- Tap Selections in the top toolbar.
- Choose a selection mode from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Pick your color.
- Make the selection. The fill is applied as soon as you finish.
Procreate remembers the Color Fill setting between sessions, so switch it off when you're done or later selections will keep filling. Color Fill also works on a single layer only, not on a group.
This method is good for geometric objects such as rectangles and ellipses. It also works for hand-drawn shapes where you want a hard boundary regardless of line quality. Combine it with Selections → Feather when you want a softened edge instead of a crisp one.
Method 4: Fill Layer
Fill Layer floods an entire layer with the Active Color. Choose your color, open the Layers panel, tap the layer, and select Fill Layer. It's good for backgrounds and base color blocks, and for setting up a layer you will mask or clip afterward.
Because it fills the whole layer, pair it with a selection or Alpha Lock if you only want part of it colored.
Method 5: Alpha Lock and clipping masks
When an object is already drawn and you want to change or add color without spilling outside it, lock its pixels.
Alpha Lock
Tap the layer thumbnail and choose Alpha Lock. Anything you paint, fill, or drop onto that layer now affects only the existing pixels. This is the fastest way to recolor a solid silhouette or apply a gradient inside a shape.
Clipping masks
Add a new layer above your shape, tap it, and choose Clipping Mask. Anything on that layer shows only where the layer below has content. This keeps the original shape untouched, so you can fill with a texture, pattern, or gradient and change your mind later. It's the better choice when you want non-destructive edits.
Method 6: Reference layers for line art
A common workflow is to keep line art on one layer and color on another underneath. If you drop color onto an empty layer, there's nothing for ColorDrop to detect, so it fills the whole layer. To fix this:
- Open the Layers panel and tap your line art layer.
- Choose Reference.
- Select the empty color layer beneath it.
- ColorDrop into the shape. The fill respects the line art but lands on the color layer.
This keeps your line work clean and lets you recolor later without touching the outlines.
Troubleshooting common fill problems
The fill covers the whole canvas
There are three likely causes:
- There's a gap in the outline. Even a tiny break lets color escape. Zoom in, close the gap with a brush, or fill on a layer where the shape is fully closed.
- The threshold is too high. Drop the color again and slide left before releasing.
- You're on an empty layer with no Reference set. Set the line art as Reference, as described above.
White spots or ragged edges
Textured brushes, such as chalk, leave semi-transparent gaps in their strokes, and the fill can stop short of them. Raise the threshold slowly, one point at a time, until the gaps close. With very grainy lines there will usually still be some mismatch between the flat fill and the line texture. If you need clean results, draw the shape with a solid brush such as a monoline, or put a flat fill on a layer beneath the textured lines.
Colored fringe or halo around edges
Antialiased edges leave partially transparent pixels that a fill can miss. Try a slightly higher threshold, or fill onto a separate layer below the line art so the lines overlap the edges of the fill. For silhouettes, Alpha Lock avoids the problem because it follows the existing edge.
Color Fill won't work
Check that you're on a single layer, not a group, and that Color Fill is actually highlighted in the Selections toolbar.
Choosing the right method
Getting Procreate fills into a motion pipeline
If you're a motion designer or animator, Procreate is often where flat-color keyframes, character poses, or style references begin before they move into After Effects, Premiere Pro, or Nuke. A few habits make that handoff cleaner:
- Keep fills and line art on separate layers. Export so the layers stay separate, so you can adjust each element independently in your compositing app.
- Work at the final resolution. Set the canvas size before you start. Upscaling a fill-heavy illustration later softens edges, which is especially visible on flat color.
- Name and group layers by element. Color Fill doesn't work across groups, so do your filling first and group afterward.
- Use Alpha Lock for later color changes. If a client changes a palette, a locked layer lets you recolor in seconds instead of redrawing.
Where Styleframe fits
Procreate is excellent for creating the flat-color art. If you want to extend a set of filled illustrations into moving footage, is an AI video and motion tool that can work from your Procreate frames as references.
A typical sequence would be to fill and finalize your key poses in Procreate, export them at full resolution, generate motion from them in Styleframe, and finish the shot in After Effects with your usual color, effects, and edit.
Quick recap
- ColorDrop is the default: drag the Active Color into a closed shape and slide to set the threshold.
- Continue Filling and Recolor speed up tap-to-fill workflows.
- Selections → Color Fill fills exactly what you select, on a single layer.
- Fill Layer floods a whole layer, and Alpha Lock and clipping masks keep color inside an existing shape.
- A Reference layer lets you fill on a separate layer from your line art.
- If a fill floods the canvas, check for gaps, lower the threshold, and confirm your Reference layer.
Once you know which method suits which job, filling shapes becomes the quick part of the process, and your layered files stay clean enough to move into After Effects, Nuke, or an AI-assisted motion workflow without rework.