How to Fill in Stuff in Procreate
StyleFrame Team8 min read
To fill an area in Procreate, drag your active color from the top-right corner onto the shape (ColorDrop), then slide left or right before lifting your Pencil to set how far the fill spreads. For more control, use Selections with Color Fill turned on, fill a whole layer from Layer Options, or lock a layer with Alpha Lock to recolor only what's already painted. Each method suits a different job, from flatting line art to building backgrounds, and the right choice depends on whether your art sits on one layer or several.
Which fill method should you use?
ColorDrop: the fastest way to fill
ColorDrop works like a paint bucket you drag into place.
- Tap and hold the color dot in the top-right corner (or a swatch from a palette).
- Drag it into the area you want to fill, and keep your Pencil or finger down.
- Without lifting, slide left or right to change the ColorDrop Threshold. A percentage appears at the top of the screen. Lower values fill less, higher values fill more and bleed further past edges.
- Lift to commit.
Procreate remembers your last threshold, so if fills suddenly behave differently, check whether you changed it on a previous drop.
Continue Filling
After a ColorDrop, tap Continue Filling to fill other areas with simple taps. You can also tap, hold, and drag to adjust the threshold. Tap the checkmark at the top, or switch to another tool such as Paint, to exit.
On an iPad and Pencil that support hover, you can hover over the active color and double-tap the Pencil barrel to jump straight into Continue Filling with that color. It speeds up flatting a character or a set of shapes.
Fixing fills that flood the whole layer or leak
The most common complaint is a fill that covers the entire canvas or layer. There are two usual causes.
The threshold is too high. Drop the color again, pause, and slide the threshold down until the fill stays inside the shape.
Your line art is on a different layer. ColorDrop reads the pixels on the layer you're filling. If you drop color on a blank layer beneath your lines, it has no edges to stop at, and it floods everything. The fix is a Reference layer:
- Open the Layers panel and tap the thumbnail of your line art layer.
- Choose Reference in the Layer Options menu.
- Select a separate, empty layer beneath it and ColorDrop into your shapes.
The fill now uses the line art as its boundary but lands on the new layer. This keeps your flats and your linework independent.
Dealing with gaps
If a line has even a small opening, the color will escape. Some dedicated inking apps let you set a gap tolerance, but Procreate's ColorDrop has no equivalent setting that I'd rely on. Your options are:
- Close the gap with a small brush stroke on the line art layer.
- Lower the threshold and fill in two passes.
- Use a Selection with Freehand to define the region manually.
Also note that anti-aliased edges can leave a thin halo of unfilled pixels between a fill and a line. If you see a fringe, raise the threshold slightly or fill on a layer beneath the lines so the lines overlap the edge.
Selections with Color Fill
Selections give you precise, deliberate regions rather than relying on edge detection.
- Tap Selections at the top.
- Choose a method at the bottom: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Choose your color from the top-right dot.
- Make the selection. The fill is applied the moment you finish.
Color Fill stays on even after you leave and re-enter Selections, so turn it off when you're done or you'll fill things by accident. It only works on a single layer, not a group, so select the specific layer first.
Pair it with Feather to soften the selection edge, useful for vignettes, soft shadows, or color washes behind a subject.
Fill Layer for backgrounds and base tones
When you want one flat color across an entire layer:
- Set your color in the top-right.
- Open the Layers panel and tap the layer you want to fill. Tap it twice to open the Layer Options menu.
- Choose Fill Layer.
This is the quickest way to create solid backgrounds. Do it on a dedicated layer, not on your artwork, so you can change it later without repainting.
Alpha Lock and clipping masks: fills for gradients and patterns
Solid fills are only part of the story. To put a gradient, texture, or pattern inside a shape, you have two reliable options.
Alpha Lock
Tap a layer's thumbnail and select Alpha Lock. Everything you paint now affects only pixels that already exist on that layer, and the transparent areas are protected. Recolor a silhouette, paint a gradient across a logo, or add texture without spilling past the edge. Turn it off when you want to paint freely again.
Clipping masks
Place a new layer directly above your shape layer and choose Clipping Mask from its options. Whatever you paint on the upper layer shows only where the layer below has content. Because the fill sits on its own layer, you can swap patterns, change opacity, or adjust blend modes non-destructively. This is a better choice than Alpha Lock when you expect revisions.
The Lighten trick
You can also fill a shape with a gradient by painting the shape in black, adding a gradient layer above it, and setting that layer's blend mode to Lighten. The lighter pixels of the two layers win, so the gradient appears only where the shape is darker. It's an uncommon approach, but handy when you want the gradient on a separate, editable layer.
Recolor, the alternative to ColorDrop
Procreate also includes Recolor, a tap-to-fill mode similar to ColorDrop that is hidden unless you enable QuickMenu. To turn it on:
- Go to Actions → Prefs → Gesture Controls → QuickMenu and choose how to trigger it.
- Assign Recolor to one of the QuickMenu radial slots and tap it to enter the mode.
- Pick a color, then tap the areas you want to fill.
- Use the Flood slider to control how aggressive the fill is.
Some artists prefer it because the tap-based workflow feels closer to a traditional bucket tool. If ColorDrop already works for you, you can skip it.
Using Procreate fills in a motion pipeline
If you're an animator or motion designer, you probably use Procreate for boards, character design, hand-painted textures, or frame-by-frame passes. A few habits will make those fills easier to carry into After Effects, Nuke, or Blender:
- Keep flats on their own layers. One layer for each character part or color region makes it easier to isolate, matte, or recolor later.
- Name and group layers consistently. The same names every time save time when you import and split them out in your compositor.
- Use clipping masks instead of baked-in color so you can still change tones after delivery.
- Fill on a layer beneath the lines to avoid halos when you composite over other footage.
- Export in a format that preserves layers or transparency, and check that the edges survive your composite before you commit to a full sequence.
None of this replaces learning to fill cleanly in Procreate. Clean, well-separated fills give any downstream tool better reference material.
Troubleshooting common fill problems
- The fill covers the whole canvas. Lower the threshold, or check that you're filling on the same layer as the lines, or have set a Reference layer.
- The fill leaves a white fringe. Raise the threshold a little, or fill on a layer beneath the line art.
- Color Fill won't work on a group. Select a single layer inside the group instead.
- Selections keep filling automatically. Turn off Color Fill in the Selections toolbar.
- A fill spills outside a shape you wanted to recolor. Use Alpha Lock or a clipping mask instead of ColorDrop.
- Recolor isn't in the menu. Enable QuickMenu in Gesture Controls and assign Recolor to a slot.
The short version
Use ColorDrop for speed, a Reference layer for fills that must respect line art, Selections for precision, Fill Layer for backgrounds, and Alpha Lock or clipping masks when the fill needs to be a gradient, texture, or something you'll revise. Set up your layers so they're ready for compositing, and your Procreate work will move into the rest of your pipeline without extra cleanup.