How to Fill in Lineart Procreate
StyleFrame Team6 min read
To fill lineart in Procreate, keep your lines on their own layer, set that layer as the Reference layer, add a new layer underneath, and drag a color from the top-right into each closed shape with ColorDrop. Hold after dropping and slide left or right to adjust the threshold until the fill reaches the edge of the line without leaking. If white fringes show where the lines meet the color, fill beneath the lines instead of stopping at their edge: select outside your drawing with Automatic selection, invert it, and fill on a layer below the lineart.
Set up your layers before you fill
Most fill problems are layer problems. Before you touch ColorDrop, set up a structure that lets you change your mind later:
- Lineart on its own layer. If your lines are spread across several layers, group them, duplicate the group, and merge the duplicate. Keep the originals hidden as a backup.
- Color on one or more layers beneath the lines. Never fill on the lineart layer unless you want the fill to be permanent.
- Reference layer enabled on the lineart. Tap the lineart layer, choose Reference, and Procreate will calculate fills from the lines while you paint on a different layer.
This matters for animators and motion designers because a clean separation between lines and color makes later edits and hand-off easier, so you can recolor or adjust each element independently.
Method 1: ColorDrop with a Reference layer
This is the fastest route for clean, closed shapes.
- Select your empty color layer beneath the lineart.
- Drag the color swatch from the top-right corner into the shape you want to fill. Don't release yet.
- Keep holding and slide your Apple Pencil or finger left or right. The threshold percentage appears at the top of the screen. Moving left fills less and moving right fills more.
- Lift to commit the fill.
- Tap Continue Filling to fill other areas with a tap. Tap and drag to adjust the threshold on the fly.
Raising the threshold slightly pushes the fill into the antialiased edge of the line, which reduces the halo. Push it too far and the color escapes into neighboring areas, so increase it in small steps.
Close gaps first
ColorDrop leaks through any opening in the line. If a fill floods the whole canvas, undo it and look for a gap, even a single pixel one. You can close gaps in two ways:
- Zoom in and draw a small stroke over the gap on the lineart layer, or on a separate "patch" layer that is also included in the Reference.
- Use a fill technique that doesn't depend on closed shapes, covered below.
Method 2: Fix white lines between fills
The most common complaint with the Reference approach is a thin light seam between adjacent colors once the lineart is hidden. The fill stops at the antialiased edge of the stroke, leaving a gap. For flat-color animation, where you may hide or recolor the lines, this is a real problem. There are three dependable fixes.
Paint the lines into the fill with Alpha Lock
- Unhide the lineart layer.
- Tap the layer and choose Alpha Lock. Now you can only paint where pixels already exist, which is exactly where your lines are.
- Paint over the lines with the matching fill colors, section by section.
The lines become colored edges that merge with the fills. This works best when the lineart is on a layer by itself with nothing else on it.
Select outside, invert, fill
This is the most reliable method when you want solid color under the whole character.
- Make sure your lines are on one merged layer.
- Open Selection, choose Automatic, and tap the empty background outside the drawing. Drag to adjust the threshold until the selection hugs the outer line.
- Tap Invert. The whole silhouette, including the area under the lines, is now selected.
- Add a new layer beneath the lines and fill it with a solid color.
Now the color extends under every line, so no background shows through. Inner areas still need dividing. You can do that by filling each region with ColorDrop on this base layer, and since the lines already sit underneath on the color layer, seams are far less likely. This approach also tolerates small gaps in the outer contour, because you can close them with a brush on the color layer instead of fixing the lineart.
Fill with a Multiply layer for loose work
For a more painterly look, lock the lineart layer, add a new layer above it, and set the blend mode to Multiply. Your color then sits visually under the black lines because multiplying with black stays black. This avoids halos entirely, but it's less suitable if you need the lines and color as separate clean elements.
Method 3: Color Fill with Selections
If you'd rather work with selections than ColorDrop, use Selection → Color Fill:
- Tap Selection and choose Automatic, Freehand, Rectangle, or Ellipse.
- Turn on Color Fill. It's enabled when highlighted blue.
- Choose your color and make your selection. The color fills as soon as the selection completes.
Two caveats. Color Fill works on a single layer, not a group. And it stays on until you switch it off, so disable it when you finish or you'll fill by accident later.
Recoloring the lines themselves
Black outlines don't always suit the final look. If the lines are on their own layer, tap the layer, enable Alpha Lock, choose a new color, then tap the layer again and select Fill Layer. The line color changes instantly and the edges stay crisp.
If lines and color have been merged, use Automatic selection on the lines with a contrasting color active, drag until the outline is fully selected, copy, and paste it into a new layer. Then Alpha Lock and Fill Layer that new layer. It's a workable rescue, but keeping layers separate from the start is better.
Prepare the file for hand-off
Procreate is a capable place to draw and flat frames, but the real work often happens elsewhere. A few habits make hand-off cleaner:
- Name layers before exporting (Lines, Base Color, Shadow, and so on).
- Hide the paper color layer so exports have transparency.
- Export in a format that keeps layers when you need them, and check that the file opens with layers intact in your other software before sending a batch.
- Keep consistent canvas size and layer structure across frames so sequences line up without manual repositioning.
Keeping lines on a separate layer lets you adjust the lines without touching the fills, and the other way around.
Quick troubleshooting
- Fill floods the whole canvas: there's a gap in the lines. Close it or use the select-outside-and-invert method.
- White seam between fills: raise the ColorDrop threshold slightly, Alpha Lock and paint the lines, or fill beneath the lines.
- Fill won't stay inside the lines: confirm the lineart layer is set as Reference and that you're filling on a different layer.
- Color covers the lines: the color layer is above the lineart. Move it below, or set it to Multiply.
- Color Fill doesn't work on a group: merge the group or select a single layer.
Pick the method to match the job. ColorDrop with a Reference layer is quickest for clean shapes, select-outside-and-invert is the safest for production, and Alpha Lock is the fix for stubborn seams.