How to Fill in a Spot on Procreate
StyleFrame Team7 min read
To fill a spot in Procreate, drag a color from the top-right Colors icon into the enclosed area and hold until the threshold bar appears. Slide left or right to control how far the fill spreads, then lift your Apple Pencil or finger to commit. If the fill floods the whole canvas, set your line art layer as Reference and fill on a separate layer underneath. The sections below cover each fill method and how to fix the usual failures.
Fill a Spot with ColorDrop
ColorDrop is the fastest way to fill a small, enclosed region. It behaves like a paint bucket you drag into place instead of tapping.
- Select the layer you want to fill.
- Drag the Colors icon (top right) into the spot and keep holding.
- While still holding, drag left or right to adjust the ColorDrop Threshold. Left fills less, right fills more. The percentage appears at the top of the interface.
- Lift your Apple Pencil or finger to commit.
The threshold matters more than most people expect. It controls how aggressively the fill spreads, so a spot with soft or textured edges may need a different setting than a hard-edged vector-style shape. Pause until the threshold indicator appears, set it, then release.
Continue Filling for multiple spots
After a ColorDrop, tap Continue Filling to keep the same color and fill other spots with single taps. You can also tap, hold, and drag to change the threshold on any individual fill. Exit by tapping the tick at the top or by switching to another tool such as Paint.
On an iPad that supports Apple Pencil hover, you can hover over the current color swatch and double-tap the side of the Pencil to jump straight into Continue Filling. It saves a lot of reaching when you're flatting a full illustration.
Fill Inside Line Art with a Reference Layer
This is the setup that fixes most failed fills. By default, ColorDrop only looks at the layer you're filling. If your line art sits on a different layer from the layer you're coloring, Procreate sees an empty surface with no boundaries and floods all of it.
The fix:
- Open the Layers panel.
- Tap the thumbnail of your line art layer.
- Choose Reference from the menu.
- Select a separate, empty layer beneath the line art for your color.
- ColorDrop into the spot as usual.
With a Reference layer active, ColorDrop follows the boundaries on the reference, even at a threshold of zero. That also explains the opposite failure: if Reference is switched on for a blank or wrong layer, every fill will flood the whole canvas because there are no boundaries to respect. Check your layer thumbnails for the Reference label whenever fills behave strangely.
This approach also keeps your flats non-destructive. Line art stays untouched on its own layer, color sits on another, and you can adjust or replace either one later. For animation prep, that separation is especially useful.
Fill with Selections and Color Fill
When you want precision, or when the spot has no clean outline to detect, use a selection instead of ColorDrop.
- Tap Selections at the top.
- Choose a method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Choose your color from the Colors icon.
- Make the selection. The fill is applied as soon as the selection closes.
Freehand is the best choice for irregular spots that you need to define yourself. Automatic works well on distinct shapes. Rectangle and Ellipse suit geometric areas, and combining them with Feather gives you softened edges, useful for framing artwork.
Two things to remember:
- Color Fill stays on. Procreate remembers the setting after you leave Selections, so turn it off when you're done or your next selection will fill unexpectedly.
- It works on a single layer only. You can't Color Fill onto a group. Select an individual layer first.
If you tap Color Fill and don't see a threshold slider, that's expected. The threshold belongs to ColorDrop, not to selection-based fills.
Use Recolor as an Alternative
Recolor is an older feature that Procreate brought back after user demand. It's hidden unless you enable QuickMenu:
- Go to Actions → Prefs → Gesture Controls → QuickMenu.
- Toggle on the way you want to invoke it.
- Assign Recolor to one of the radial options.
To use it, tap Recolor in the QuickMenu, pick your color, and tap the areas to fill. The Flood slider changes how aggressive the fill is, much like the ColorDrop threshold. Some artists prefer it because it's a persistent mode: you stay in it and tap away rather than dragging each color in.
Fill an Entire Layer
If the "spot" is really the whole layer, you don't need any of the above. Pick a color, open the Layers panel, tap the layer twice to open Layer Options, and choose Fill Layer. It floods the active layer with the current color. This is handy for solid backgrounds or for building a color base you'll mask or clip other layers onto.
Troubleshooting Fills That Go Wrong
The fill covers the whole canvas
Work through these in order:
- Check for a Reference layer. If Reference is on for a blank layer, the fill has no boundaries.
- Set Reference on your line art. If lines and color are on separate layers, the line art must be the Reference.
- Lower the threshold before you release. Drag left while still holding the color, and wait for the threshold indicator to appear.
- Make sure you're using ColorDrop. Selection-based Color Fill has no threshold slider, so instructions that mention one won't apply.
The fill leaks out of the shape
Even a small gap in your outline can let the fill escape. Zoom in and close the gap with a brush. Alternatively, draw the shape with Quick Shape so the outline is sealed, or use a selection to define the area explicitly.
The fill leaves a light fringe along the edges
If a light fringe remains along the edges, try raising the threshold slightly so the fill reaches under the edge of the line. With line art on a Reference layer above, any slight overlap is hidden beneath the lines.
The fill ignores a spot that was already filled
ColorDrop responds to the pixels it sees. If a region was previously filled, a new fill may only affect the matching pixels, depending on your layer and reference setup. Confirm you're on the layer you intend to edit, and consider re-filling on a fresh layer.
Taking Filled Procreate Art into a Motion Pipeline
For motion designers, the point of flatting in Procreate is usually downstream: character parts, backgrounds, texture elements, or storyboard frames headed for After Effects, Premiere Pro, or a 3D package. A few habits make that handoff cleaner:
- Keep fills on their own layers. Using the Reference approach means line, color, and shading stay separable, which makes it simple to rig or animate pieces independently.
- Name your layers before exporting. Clear naming saves time when layered files land in After Effects.
- Fill generously under line art. Slight overlap prevents hairline gaps when elements move against each other.
- Work at the final resolution. Fills on a small canvas can show jagged edges when scaled up later.
Quick Reference: Which Fill Method to Use
Final Tips
Most fill problems come from two settings: the threshold and the Reference layer. Before troubleshooting anything else, check whether a layer is marked Reference and whether your threshold is where you want it before you lift the Pencil. Build the habit of lines on top, color below, and Reference set on the lines. Fills then become predictable, and your layered files stay easy to animate once they leave Procreate.