How to Fill Color on Another Layer in Procreate
StyleFrame Team7 min read
To fill color on another layer in Procreate, set your line art layer as the Reference layer: open the Layers panel, tap the layer's thumbnail, and choose Reference. Then select an empty layer above or below it and drag a color from the top-right Colors icon into the area you want to fill. ColorDrop reads the Reference layer's edges to decide where the fill goes but paints onto the active layer. If the fill floods the whole canvas or leaks out, adjust the ColorDrop Threshold by holding your finger or Apple Pencil on the canvas after dropping and sliding left or right.
Why Procreate Fills the Wrong Layer by Default
By default, Procreate's fill tools look at the pixels on the layer you're painting on. If you draw a shape on one layer, add a new empty layer beneath it, and drop a color, there is nothing on that empty layer to bound the fill, so the whole canvas floods.
The Reference layer fixes this by separating two jobs that are normally tied together:
- Which layer defines the boundaries. This is the Reference layer, usually your line art.
- Which layer receives the color. This is whichever layer is active.
Once you split them, you can keep line art untouched on top and put each flat color on its own layer underneath. That is the same structure compositors expect when they receive layered artwork.
Step-by-Step: Fill Color on a Separate Layer with a Reference Layer
- Isolate your line art on one layer. The cleaner and more closed the linework, the better the fills behave. Keep linework off the color layers.
- Set the Reference layer. Open Layers, tap the line art thumbnail to open Layer Options, and tap Reference. A checkmark appears beside the option, and the word "Reference" shows on the thumbnail.
- Create a new layer. Place it above or below the Reference layer. Layers on either side of the Reference layer work, so line art can stay at the top of the stack.
- Select the new layer. Make sure it's the active layer, not the line art.
- Drag the color in. Drag the Colors icon from the top right into the enclosed area. The fill lands on the active layer, bounded by the Reference layer's lines.
- Repeat on new layers. Make a layer for hair, another for skin, another for clothing, and drop colors into each. The Reference layer keeps defining the boundaries without you touching it again.
A useful side effect is that you can hide the line art afterward and be left with clean, separate color shapes. These work as masks if you later want to select a region and paint inside it.
Tuning ColorDrop Threshold
ColorDrop doesn't just fill pixels of the same color. It floods outward based on a threshold, which is why you sometimes get gaps, halos, or leaks.
- Drag a color into an area and keep holding instead of lifting right away.
- A threshold percentage appears at the top of the canvas.
- Slide left to fill less aggressively, or right to fill more.
- Lift to commit the fill.
Lower thresholds can leave a thin unfilled fringe along antialiased edges. Higher thresholds push the fill up to and under the line edges, which is usually what you want when line art sits on top and the color layer sits below. Fills that go slightly under the lines hide any seam.
Use Continue Filling for Speed
After one ColorDrop, tap Continue Filling to fill other areas with simple taps. You can still tap, hold, and drag to change the threshold. Tap the checkmark at the top, or switch to another tool such as Paint, to exit. This saves a lot of time when you're laying in many flat regions on the same layer.
If your iPad and Apple Pencil support hover, you can hover over the current color in the top right and double-tap the side of the Pencil to start Continue Filling immediately with that color.
Other Ways to Put Color on a Different Layer
The Reference layer is the most flexible approach, but a few other methods suit specific situations.
Selections with Color Fill
The Selections tool has a Color Fill option that fills anything you select with your current color as soon as the selection is complete.
- Tap Selections.
- Pick a selection method (Automatic, Freehand, Rectangle, or Ellipse).
- Tap Color Fill so it highlights blue.
- Choose your color.
- Make the selection on the target layer.
Two things to keep in mind. Color Fill works only on a single layer, not on a group of layers. And Procreate remembers the setting after you leave Selections, so turn it off when you're done or you'll fill things by accident.
Fill Layer
If you want the entire layer to be one color, choose your color, open Layers, tap the target layer to open Layer Options, and use Fill Layer. This is useful for solid backgrounds or for creating a flat base you'll later cut into with a mask or eraser.
Recolor
Recolor is an older flood-fill tool that Procreate brought back. It's available only through QuickMenu, which is off by default. Enable it under Actions → Prefs → Gesture Controls → QuickMenu, assign Recolor to one of the radial options, then tap areas to fill. The Flood slider controls how aggressively it fills.
Troubleshooting Common Problems
The fill still floods the whole canvas. Check that the Reference layer actually shows the Reference label and that your active layer is a different, empty layer. If you've set the wrong layer as Reference, the boundaries won't be where you expect.
The color leaks out of a shape. There's a gap in your line art. Close it with a small brush stroke on the line art layer, or lower the threshold to see whether the leak is threshold-related. Gaps are the most common cause.
There's a white or uncolored fringe along the lines. Raise the threshold so the fill extends under the edge of the line art. With the line art above and the color below, the overlap is invisible.
Color Fill with Selections won't work. Confirm you're targeting a single layer rather than a group.
Fills hit the wrong shapes. Make sure the layer marked as Reference is the one you intend. The Reference layer should be the one with the most closed, clean boundaries.
Organizing Layers for a Motion Pipeline
For motion designers and animators, the real payoff of filling on separate layers is what happens after Procreate. A layered file with line art on top and flat color regions below gives you something you can treat as production assets rather than a flattened picture.
A few habits help:
- Name layers by region or material, such as "skin," "hair," and "jacket," before exporting. Clear layer names save time later.
- Keep line art separate from color so you can adjust, recolor, or replace either independently.
- Export in a format that keeps layers intact when you want to preserve them, so you can animate, parallax, or rig each color region individually in your compositor.
- Fill slightly under the lines so you don't see seams when you move layers apart.
- Use flat color regions as mattes. A solid fill on its own layer can serve as a matte or selection source in your compositor.
Procreate's tools are built for illustration, not motion, so the cleanest approach is to finish the art there and do the movement in your compositor.
Quick Reference
Final Takeaway
Filling color on another layer in Procreate comes down to one setting: mark your line art layer as Reference, select a different layer, and drop color in. Tune the threshold to avoid leaks and fringes, keep each color region on its own named layer, and export in a layered format so the work carries into the rest of your pipeline.