How to Fill Certain Areas in Procreate
StyleFrame Team7 min read
To fill a specific area in Procreate, drag your active color from the top-right corner into a closed shape. This is ColorDrop, and holding before you release lets you adjust the Threshold to control how far the fill spreads. For more precise control, use Selections with Color Fill turned on, or fill a whole layer from its Layer Options menu. If a fill floods the entire canvas, the usual cause is a missing or misplaced Reference layer, or a Threshold that is set too high.
Fill an Area with ColorDrop
ColorDrop works like a bucket tool you drag into place.
- Pick your color from the Colors icon in the top-right corner.
- Drag that icon onto the area you want to fill.
- Keep your Apple Pencil or finger down until you are happy with the preview.
- Lift to commit the fill.
ColorDrop spreads until it detects an outline. That means your shape needs to be closed. A gap in a contour can let the color leak into neighboring regions.
Adjust the ColorDrop Threshold
The Threshold controls how much of an area the fill covers.
- Drag your color into the area, but do not release.
- Hold still until a thin blue bar appears above the canvas, showing the Threshold amount.
- Drag left to fill less, or right to fill more.
- Release when the preview looks right.
Procreate remembers the last Threshold you used. If a new fill looks too tight or too loose, the previous setting is probably the cause. Check it before each fill when you switch between artwork with different line quality.
Adjust in small increments and watch the preview.
Fill Multiple Areas with Continue Filling
After a ColorDrop, tap Continue Filling to fill other regions with single taps instead of dragging the color each time. You can also tap, hold, and drag to change the Threshold on the fly. Exit by tapping the checkmark at the top or by switching to another tool such as Paint.
If you use an Apple Pencil on an iPad that supports hover, you can hover over your current color in the top-right corner and double-tap the Pencil to start Continue Filling with that color right away. It removes a lot of repeated dragging when you are flatting an illustration with many small shapes.
Fill Exact Shapes with Selections and Color Fill
When you need a fill that follows a shape you define yourself, rather than one detected from line art, use Selections with Color Fill.
- Tap Selections at the top.
- Choose a method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Choose a color from the Colors icon.
- Make your selection. The fill applies as soon as the selection closes.
This approach suits geometric shapes, panels, and backgrounds. Combine it with Feather to soften the edges of a rectangle or ellipse fill, which is useful for framing a composition.
Two things to remember:
- Color Fill stays enabled after you leave Selections. If your next selection fills unexpectedly with color, turn the setting off.
- Color Fill only works on a single layer. You cannot use it on a group.
If you open the Selection tools expecting a Threshold slider, you will not find one. That slider belongs to ColorDrop, not to Color Fill within Selections.
Use Recolor as an Alternative
Recolor is an older tool that Procreate brought back after users asked for it. It is not visible by default. You reach it through QuickMenu, which you have to enable first:
- Open Actions → Prefs → Gesture Controls → QuickMenu.
- Toggle on the gesture you want to use to open it.
- Assign Recolor to one of the radial slots.
To use it, tap Recolor in QuickMenu, choose your color, and tap the areas you want to change. The Flood slider sets how aggressive the fill is, which makes it similar to the ColorDrop Threshold.
Fill an Entire Layer
Sometimes the "certain area" is the whole layer, such as a flat background or a base tone for a character.
- Select your color.
- Open Layers and tap the target layer twice to open Layer Options.
- Choose Fill Layer.
Fill Layer fills the layer with the color, so duplicate the layer first if you may want the original back. If you only want to color the pixels already on the layer, use Alpha Lock instead (covered below).
Fix a Fill That Floods the Whole Canvas
A common complaint is a fill that covers the entire page. Work through these checks in order.
Check for a Reference layer
Reference tells ColorDrop to read boundaries from one specific layer, even when you are filling on another. This is a typical setup for flatting: line art on one layer, colors on a layer beneath.
- If your line art is on a separate layer and Reference is off, ColorDrop sees an empty layer with no boundaries and floods it.
- If Reference is switched on for the wrong layer, especially a blank one, ColorDrop reads nothing and floods the layer you are working on.
Open the Layers panel, look for the Reference label on layer thumbnails, and tap a layer to toggle it. Make sure only your line art layer has it enabled. With a valid Reference layer, ColorDrop respects its lines even when the Threshold is at zero.
Check the Threshold
If you are filling on the same layer as your lines and still get a flood, the Threshold may be too high, or your shape may not be closed. Lower the Threshold, then zoom in and close any gaps in the contour with a small brush stroke.
Confirm you are using the right tool
If you cannot find a Threshold slider, you may be using Color Fill inside Selections rather than ColorDrop. The two behave differently, so switch tools depending on whether you want a detected fill or a defined selection.
Keep Color Inside the Lines with Alpha Lock and Clipping Masks
Filling is only half of the job. Once you have flat colors, you will often want to shade or texture them without spilling over the edges. Two layer features handle that:
- Alpha Lock restricts painting to pixels that already exist on the layer. Swipe two fingers right on the layer, or choose it from Layer Options. Anything you paint stays within the existing shape.
- Clipping Mask attaches a new layer to the one below it, so painting on the upper layer only appears where the lower layer has content. This keeps your flats untouched and lets you delete or adjust shading separately.
For motion work, clipping masks are usually the better choice because they keep each element non-destructive and easy to revise.
Which Fill Method Should You Use?
Using Procreate Fills in a Motion Pipeline
Some motion designers use Procreate to build styleframes, character flats, or background paintings before moving into After Effects, Cinema 4D, or Nuke. A few habits make that handoff smoother:
- Keep line art, flats, shading, and effects on separate layers so each can be animated or adjusted independently.
- Name your layers before exporting, and export a layered file if you plan to rebuild the comp in After Effects.
- Leave a small overlap between adjacent fills if you expect to animate or distort shapes, since hairline gaps can show up when layers move.
Quick Troubleshooting Reference
- Fill covers the whole canvas: check for a missing or misplaced Reference layer, then lower the Threshold.
- Color leaks into nearby shapes: close gaps in the line art or lower the Threshold.
- Color Fill will not work on a group: merge the group or select a single layer.
- Selections keep filling automatically: turn Color Fill off.
- Recolor is missing: enable QuickMenu and assign Recolor to a slot.
Once you know which tool matches the job, filling in Procreate becomes predictable: ColorDrop for speed, Selections for precision, Reference for clean flatting, and Alpha Lock or clipping masks to protect what you have already built.