How to Fill Area in Procreate
StyleFrame Team6 min read
The fastest way to fill an area in Procreate is ColorDrop: drag your active color from the top-right corner into a closed shape and release. Hold your finger or Apple Pencil on the canvas before releasing, then slide left or right to change the ColorDrop Threshold, which controls how much area floods. For more control, use Continue Filling, Recolor, Selections → Color Fill, or Fill Layer.
If you're a motion designer or animator using Procreate for storyboards, style frames, or character art, the fill method you choose affects how cleanly the artwork carries into After Effects or other tools later.
Fill an area with ColorDrop
ColorDrop works like a bucket tool. It fills until it detects an outline.
- Tap and drag the color swatch in the top-right corner onto the area you want to fill.
- Release to fill. To adjust the fill first, keep holding after the color floods in.
- A blue bar and a percentage appear at the top of the canvas. Slide left to fill less, right to fill more.
- Lift to commit.
Procreate remembers the last threshold you used. If a fill suddenly floods the whole layer or stops short, a stale threshold is the most likely cause, so check it first.
Fix gaps and leaks
ColorDrop only fills what the line work contains, which causes two common problems:
- The color floods the whole canvas. There's almost certainly a gap in your outline. Undo with a two-finger tap, close the gap with a brush, and try again. A threshold set too high can also cause this.
- Specks or halos remain along the edge. This happens with textured or semi-transparent brushes, such as chalk, because the line has tiny holes. Raise the threshold slowly while holding, a percentage point at a time, until the gaps fill. Expect some mismatch between a solid fill and grainy line work.
If you need clean, solid shapes, draw the outlines with a hard, fully opaque brush. Use texture on a separate layer.
Make sure you're filling the right layer
ColorDrop reads the layer you're working on. If you draw the outline on one layer and fill on another, you'll be filling an empty layer, so the color covers everything. The fix is to set the outline layer as a Reference: tap the layer, choose Reference, then select your empty layer and drop the color. Procreate now detects the line art on the reference layer but puts the fill on your active layer.
This is the standard approach for coloring line art non-destructively. Ink on one layer and flats on layers beneath it let you recolor or revise without touching the drawing.
Keep filling with Continue Filling
After a ColorDrop, tap Continue Filling in the top bar to fill more areas with the same color by tapping them. Tap and hold, then drag, to adjust the threshold for any single fill. To exit, tap the tick at the top or switch to another tool such as Paint.
If your iPad and Apple Pencil support hover, you can hover over the active color swatch and double-tap the side of the Pencil to start Continue Filling with that color. It's a good shortcut when you're flatting a whole character.
Use Recolor
Recolor is an older fill method that Procreate brought back. It's available only through QuickMenu, which is off by default.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and turn on your preferred trigger.
- Set one of the QuickMenu radial options to Recolor.
- Invoke QuickMenu and tap Recolor to enter the mode.
- Pick a color in the top right, then tap the areas you want to fill.
- Use the Flood slider to make the fill more or less aggressive.
Recolor behaves like ColorDrop with a tap instead of a drag. Some artists prefer it for rapid flatting.
Fill with Selections and Color Fill
When the area isn't bounded by line art, make a selection and let Procreate fill it.
- Tap Selections at the top.
- Choose a method from the tabs at the bottom: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it's highlighted blue.
- Pick your color in the top right.
- Make the selection. The area fills as soon as you finish.
Some points worth knowing:
- Color Fill is remembered between sessions. Turn it off when you're done, or later selections will fill unexpectedly.
- It works on a single layer only. You can't Color Fill onto a group.
- Use Feather to soften the selection edge, useful for vignettes or soft shapes.
- Freehand selections are good for hand-cut shapes. Rectangle and Ellipse are good for geometric backgrounds.
Fill an entire layer
To flood a whole layer with one color:
- Choose your color in the top right.
- Open Layers and tap the target layer twice to open Layer Options.
- Tap Fill Layer.
This suits solid backgrounds and base layers for color-blocking. To fill only the pixels already on a layer, such as recoloring a flat shape without spilling, use Alpha Lock on that layer and then fill. Alpha Lock restricts changes to existing pixels and keeps transparent areas transparent. If you turn it on and only your outlines change color, you're probably on the line art layer rather than the fill layer.
Which method should you use?
Troubleshooting common fill problems
- Fills the whole canvas: Check for gaps in the outline, then lower the threshold. If the outline is on another layer, set it as Reference.
- White specks left behind: Raise the threshold, or redraw the outline with an opaque brush.
- Color Fill does nothing on a group: Select a single layer instead.
- Fills keep appearing after you finish: Color Fill in Selections is still enabled. Toggle it off.
- Edges look jagged or crunchy: Avoid high thresholds on soft brushes. Fill on a separate layer and clean up the edge with a small eraser or a feathered selection.
Prepare filled artwork for a motion pipeline
If your Procreate art is headed for animation or compositing, fill discipline pays off downstream:
- Keep fills on separate layers from line art. Flats, shading, and ink should stay independent so you can export them as separate passes.
- Export PNG with transparency when you need to bring layers into After Effects, Premiere Pro, or Blender. Hide the background layer first.
- Use consistent, flat colors. Clean flats give any later processing, such as keying, matte extraction, and style transfer, a clearer reference.
- Work at the largest canvas size you can. Resolution you don't have can't be recovered later, and large canvases give you room to crop and reframe.
Quick reference
- Drag the color from the top right into a closed shape.
- Hold before releasing to adjust the threshold.
- Set line art as Reference if you fill on a different layer.
- Tap Continue Filling to flat multiple areas fast.
- Use Selections → Color Fill for shapes without outlines.
- Use Fill Layer for solid backgrounds, and Alpha Lock to fill within existing pixels.
Most fill problems come down to three things: the threshold, gaps in the line art, and which layer is active. Check those and the fill will behave predictably.