How to Fill an Area with Color in Procreate
StyleFrame Team7 min read
To fill an area with color in Procreate, drag the color swatch from the top-right corner into a closed shape. This is ColorDrop. Before lifting your Apple Pencil or finger, slide left or right to adjust the Threshold, which controls how far the fill spreads. For more control, use Selections → Color Fill to fill a selected shape, or Layer Options → Fill Layer to flood an entire layer.
The sections below cover each method, when to use it, and how to fix the usual problems: fills that flood the whole canvas, white halos along the edges, and fills that won't stay on one layer.
Method 1: ColorDrop (the fastest fill)
ColorDrop works like a paint bucket you drag into place. It's the primary fill tool in Procreate.
- Select the layer that holds your line art, or the layer you want to fill (see the layer notes below).
- Pick your color from the Colors icon in the top right.
- Drag that Colors icon into the area you want to fill, and keep holding.
- While still holding, drag left or right to adjust the ColorDrop Threshold. Left fills less, right fills more. A percentage readout appears at the top of the interface.
- Lift your Pencil or finger to commit the fill.
If you have the Colors panel open and floating, you can also drag the current color from the color disc or from a palette swatch. That's handy when the fill color differs from your outline color.
Continue Filling
After a ColorDrop, Procreate shows a Continue Filling option. Tap it, and each tap on the canvas fills another area with the same color. You can still tap, hold, and drag to change the Threshold on any fill. Tap the checkmark at the top, or switch to another tool such as Paint, to exit.
If your iPad and Pencil support hover, you can hover the Pencil tip over the current color in the top right and double-tap the Pencil's side to start Continue Filling with that color right away.
Method 2: Selections with Color Fill
If you want fills bounded by a shape you define rather than by line art, use a selection.
- Tap Selections at the top.
- Choose a selection method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it turns blue.
- Pick your color from the Colors icon.
- Make the selection. The color fills the area as soon as the selection closes.
Selections suit clean geometric shapes, such as panels, circles, and bars, and give you precise edges. You can also use Feather to soften a selection's edge, which works well for vignettes or soft color fields.
Two things to know:
- Color Fill is remembered. It stays enabled after you leave and re-enter Selections, so turn it off when you're done or you'll fill things by accident.
- It works on a single layer only. You can't Color Fill onto a group of layers.
Method 3: Fill Layer
When you want a flat color across an entire layer, such as a background or a base for blending modes:
- Choose your color.
- Open the Layers panel and tap twice on the target layer to open Layer Options.
- Tap Fill Layer.
With Alpha Lock on, it fills only the pixels already on the layer, which is a quick way to recolor a shape without touching the transparent area around it.
Method 4: Recolor via QuickMenu
Recolor is an older fill tool that Procreate brought back after users asked for it. It's an alternative to ColorDrop and Continue Filling, but it's hidden unless you turn on QuickMenu.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and enable your preferred way of invoking it.
- Set one of the QuickMenu radial options to Recolor, then tap it to enter the mode.
- Select your color.
- Tap the areas you want to fill.
- Use the Flood slider to control how aggressive the fill is.
Recolor suits artists who like tap-to-fill and want the tool one gesture away. Flood plays the same role here that Threshold plays in ColorDrop.
Fixing the common problems
Most failed fills come down to a few causes.
The fill covers the whole canvas
- The shape isn't closed. Even a tiny gap in the outline lets the color escape, and it will fill everything. Undo with a two-finger tap, close the gap with a brush, and fill again.
- The Threshold is too high. Drop the color again, hold, and slide left to lower it. Procreate remembers the setting until you change it.
- You're on an empty layer. ColorDrop reads the active layer by default. If your line art is on a different layer, you'll be filling transparent pixels, which floods the entire layer. Either draw on the same layer, or set the line art layer as the Reference in its Layer Options and fill on a separate layer beneath it.
White spots or gaps at the edges
This usually happens when your lines were drawn with a textured or semi-opaque brush. The grain leaves partial gaps, and the fill stops short of them. Try these fixes:
- Hold after dropping and slowly raise the Threshold, a percentage point at a time, until the gaps close.
- Fill on a layer underneath the line art so any leftover gaps are hidden.
- Redraw the outline with a solid, opaque brush such as a monoline brush.
Even with a higher Threshold, a flat fill next to a grainy line may never match perfectly. If the look matters, treat the fill and the texture as separate layers.
Fills don't respect a single layer
Some artists report that in Procreate 5, ColorDrop affects the whole canvas instead of one layer. This may be related to the Reference setting. With a reference layer set, the fill is calculated from that layer's contents. Check which layer is set as Reference, and clear it if you want the fill to read only the active layer.
A clean flat-color workflow
For most illustration and design work, this order avoids rework:
- Draw line art on its own layer with a solid, closed outline.
- Set that layer as Reference.
- Create a new layer beneath it for color.
- ColorDrop each region on the color layer.
- Turn on Alpha Lock on the color layer for later recoloring, then use Fill Layer or ColorDrop to change hues without losing shape edges.
Keeping color, line, and shading on separate layers also pays off when you export, as the next section explains.
Using Procreate fills in a motion pipeline
Procreate is rarely the final destination for animators and motion designers. It's where you build character sheets, storyboard frames, textures, mattes, and style references that move into After Effects, Cinema 4D, Blender, or Nuke.
A few habits make that handoff smoother:
- Keep fills on separate layers from line art and shading, so you can animate or adjust them independently once the file opens in After Effects.
- Use flat, closed shapes for mattes. A solid ColorDrop or Selections fill gives you a clean shape to use as a track matte or alpha source.
- Export at the resolution you'll need. Set the canvas size at the start. Upscaling a small canvas later softens the hard edges that make flat fills look sharp.
- Name your layers before you export. Clear layer names save time in your compositing software.
Quick reference
Summary
ColorDrop covers most fill jobs: drag the color into a closed shape, hold, and adjust the Threshold until the edges are right. Switch to Selections → Color Fill for shape-defined fills, Fill Layer for whole-layer color, and Recolor when you want tap-to-fill. When a fill misbehaves, check for gaps in the outline, then the Threshold, then which layer is active and which is set as Reference. Keep fills on separate, well-named layers and the files carry cleanly into After Effects, Nuke, and the rest of your pipeline.