How to Fill an Area in Procreate Pocket
StyleFrame Team7 min read
To fill an area in Procreate Pocket, open the Colors panel, choose a color, then drag the Active Color swatch from the top right onto the canvas and release it inside the shape. This is ColorDrop, a flood fill that spreads outward until it hits a boundary such as an outline or a change in color. For more control, use Selections to isolate the area first, or fill an entire layer from its Layer Options.
Fill an Area with ColorDrop
ColorDrop is a speedy way to flood-fill areas, which makes it a good fit for flat color work.
- Tap the Colors icon and pick your color using the Color Disc, Classic, Harmony, Value, or Palettes tab.
- Make sure the layer you want to fill is the active layer.
- Drag the Active Color swatch (in the top right) out onto the canvas and position it over the area you want to fill.
- Keep your finger down. Slide left or right to change the fill threshold. The percentage appears at the top of the screen.
- Lift your finger to commit the fill.
The fill expands from the point where you drop it. It stops at an edge, which can be a drawn line or an area of a different color on the same layer. A low threshold keeps the fill tight to the area you dropped on. A higher threshold pushes the fill into neighboring pixels that are similar but not identical, which is useful for soft or textured edges.
Why a fill sometimes floods the whole canvas
If the color leaks across the page, the shape you are filling is almost certainly not closed. Zoom in on your line art and look for tiny gaps, especially where strokes meet at corners. Close the gap with a small brush stroke on the line layer, then drop the color again. You can also lower the threshold, though that treats the symptom rather than the open line.
Fill Into Line Art Without Losing the Edges
A common problem with line art is that the fill stops at the edge of the line but leaves a thin halo of unfilled, anti-aliased pixels between the color and the ink. Two habits fix most of it:
- Raise the threshold slightly. Dragging the fill a bit higher pulls the color under the soft edge pixels of the line.
- Keep line art and color on separate layers. Put the ink on its own layer and the color layer beneath it. Any slight overlap is hidden behind the line, and you can recolor without touching the drawing.
This separation matters later if the artwork is going into a compositing app, because each color region stays editable and the line work stays crisp.
Fill with Selections for Precise Shapes
When ColorDrop can't find a clean boundary, such as with painterly shapes, textured edges, or geometric blocks, define the area yourself with a selection and fill it.
- Expand the top toolbar with the ellipsis and tap the Selection button (the S icon).
- Choose a mode from the toolbar at the bottom of the screen:
- Automatic selects an area with a single tap. As with ColorDrop, you can drag to change its threshold.
- Freehand lets you draw a fluid line, or tap to place polygon points. You can combine both in one selection.
- Rectangle and Ellipse are for quick geometric selections.
- Use Add to build complex shapes from several selections.
- Tap another tool to commit the selection. The area outside it becomes shaded with diagonal lines.
- Fill the selected area. You can drag the Active Color into it, or, if your version of Procreate has the Color Fill toggle in the Selection toolbar, enable it so each selection fills as soon as you complete it.
Anything you paint, smudge, erase, or fill now stays inside the selected area. That makes selections a good choice for gradients, textures, and shading, where you want the color to stay inside a silhouette without a hard outline to catch it.
Two-finger tap undoes your last action while you're still drawing a selection, and three-finger tap redoes it. To cancel a selection and go back to the artwork, tap the Selection button again.
A note on layer groups
Color Fill works on a single layer, not on a group. If the artwork is organized in a group, select a specific layer inside the group before filling. Otherwise the result may not be what you expect.
Fill an Entire Layer
To flood a whole layer with one color, for example to make a solid background or a base matte:
- Choose your color in the Colors panel.
- Open the Layers panel and tap twice on the layer you want to fill.
- In the Layer Options menu, choose Fill Layer.
Because Fill Layer floods the whole layer, use it on a new, empty layer rather than on a finished drawing. If you want the fill limited to a shape, make a selection first and then fill, so only the selected area is affected.
Other Fill Tools Worth Knowing
Procreate's wider documentation describes two extra options that may be available depending on your version and settings. Check Pocket's interface to confirm what you have:
- Continue Filling appears after a ColorDrop. Instead of dragging for each area, you tap each additional region to fill it with the same color. It's a quick way to flat a whole drawing in one pass. Tap the tick or switch to another tool to exit.
- Recolor is an alternative to ColorDrop that you can assign to the QuickMenu. You tap the areas you want to fill and adjust a Flood slider to control how aggressively it fills.
If you do a lot of flatting, practice Continue Filling. It removes the repeated drag-and-release motion and speeds up character and background flats noticeably.
Which Method Should You Use?
Prepare Procreate Fills for an After Effects Pipeline
Procreate Pocket can be used for fast concept sketches, storyboard frames, texture elements, and hand-drawn assets. A few habits make those files easier to use downstream:
- Organize by element. Put each character part, prop, or background plane on its own layer so it can be separated and animated in After Effects or Nuke.
- Keep fills on transparent layers. Fill shapes on empty layers instead of flooding a full-canvas layer, so exported PNGs carry usable alpha.
- Hide the background layer before export if you want transparency. Otherwise the export will include it as a solid color.
- Work at the final resolution. Start with a canvas large enough for your composition. Upscaling a small raster later softens the edges of your fills.
- Name your layers. Clear names save time when the file hits a compositing timeline.
The cleaner your flats, the easier they are to key, matte, or use as references.
Troubleshooting Common Fill Problems
The fill leaks into the whole canvas. Look for gaps in your lines and close them, or switch to a selection-based fill.
The fill leaves a white or light fringe along the lines. Raise the threshold a little, or place the color layer beneath the line art so the overlap is hidden.
The fill is applied to the wrong layer. Check which layer is active before dropping the color, and confirm you're not working on a group.
The fill covers more than the area you wanted. Lower the threshold during the drag, or make a selection first to confine the fill.
The fill is too jagged on soft shapes. Use a selection with Feather, or paint the shape with a soft brush rather than using a hard-edged flood fill.
Summary
Drag the Active Color onto the canvas for fast ColorDrop fills, adjust the threshold while you hold, and close gaps in your line art to prevent leaks. Use selections when you need precision, and Fill Layer for solid backgrounds. Keep fills on separate, clearly named layers, and your Procreate Pocket artwork is ready to move into After Effects or Nuke.