How to Fill a Circle with Color in Procreate
StyleFrame Team7 min read
To fill a circle with color in Procreate, draw the circle, pick a color, then drag the color from the Colors icon in the top right and release it inside the circle. This is called ColorDrop. If the color spills across the whole canvas, hold your finger or pencil down after dropping and slide left to lower the ColorDrop Threshold. You can also use Selections with Color Fill, Recolor, or Alpha Lock for more control.
Step 1: Draw a clean circle with QuickShape
A fill is only as clean as the outline it sits in, so start with a closed, even circle.
- Create a canvas and pick a brush. A solid brush like Studio Pen works well for outlines.
- Choose an outline color from the Colors icon in the top right.
- Draw a circle in one stroke, and keep your pencil or finger on the screen at the end of the stroke.
- Hold for a moment. Procreate snaps the rough stroke into a clean circle.
Don't lift before the snap happens, or you'll keep the wobbly version. Make sure the loop actually closes. A gap of even a pixel or two lets a fill leak out into the rest of the layer.
Step 2: Fill the circle with ColorDrop
ColorDrop is Procreate's primary fill method. It works like a paint bucket you drag onto the canvas.
- Tap the Colors icon in the top right and choose your fill color.
- Drag from the color swatch (the circle icon in the top right) into the middle of your circle.
- Keep your pencil or finger down for a moment after the color floods in.
- Release to commit the fill.
You can also drag a swatch from a saved palette instead of the active color.
Control the ColorDrop Threshold
While you're still holding after the drop, a Threshold percentage appears at the top of the canvas. Slide left to fill less aggressively and right to fill more. Procreate remembers the setting until you change it.
Threshold matters most with imperfect outlines:
- Too high: The color bleeds past the edge, or floods the whole layer.
- Too low: You get a halo of unfilled pixels along the inside of the outline, especially where the edge is anti-aliased.
- Just right: The fill reaches the line cleanly without crossing it.
If you see a thin light fringe between the fill and the outline, nudge the threshold up a few percent while still holding.
Fill multiple circles with Continue Filling
After a ColorDrop, tap Continue Filling at the top. Now every tap on the canvas fills the area you tap with the current color. You can also tap, hold, and drag to adjust the threshold on the fly. Tap the checkmark or switch to another tool like Paint to exit the mode.
On an iPad that supports Apple Pencil hover, you can hover over the active color in the top right and double-tap the side of the pencil to jump straight into Continue Filling with that color.
Alternative methods for filling a circle
ColorDrop is quick, but it isn't the only route. Each of these suits a different situation.
Selections with Color Fill
This approach skips the outline-then-fill step. You select a circular area, and Procreate fills it as soon as the selection completes.
- Tap Selections at the top.
- Choose the Ellipse tab at the bottom.
- Tap Color Fill so it highlights blue.
- Choose your color from the Colors icon.
- Drag out an ellipse on the canvas. The fill appears when you lift.
This is useful when you want a flat shape with no outline at all, or when you want to use Feather to soften the edge. Two things to watch:
- The Color Fill setting is remembered, so turn it off when you're finished or your next selection will fill unexpectedly.
- Color Fill works on a single layer. You can't use it when a group is selected.
Recolor
Recolor is an older tool Procreate brought back. It's hidden by default and is reached through QuickMenu.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and toggle on how you want to invoke it.
- Set one of the radial options to Recolor.
- Choose your color, then tap inside the circle.
- Use the Flood slider to control how aggressively it fills.
Recolor behaves like a tap-to-fill bucket and is useful if you prefer that over dragging a color from the corner.
Fill Layer
If the circle is the only thing on its layer and you want to flood the whole layer, use Fill Layer:
- Pick a color.
- Tap Layers, then tap your layer twice to open Layer Options.
- Choose Fill Layer.
On its own, this fills everything on the layer, so it makes sense paired with a selection or Alpha Lock. It's not the way to fill a single circle on a busy layer.
Alpha Lock for filling an existing shape
Alpha Lock restricts painting to pixels that already exist on the layer. Once your circle is drawn as a solid shape:
- Tap the layer thumbnail and choose Alpha Lock.
- Pick a color and use Fill Layer, or paint over the shape with any brush.
Color only lands where the circle is, and the edges stay intact. This is also a good way to apply gradients to a shape. Create the gradient directly on the alpha-locked layer.
Another approach is to put a gradient layer above a black shape and set the gradient layer to the Lighten blend mode. The gradient shows through where the shape is black.
Fixing common problems
The fill covers the whole canvas
This is the most common complaint, and it has a few causes:
- Threshold too high. Re-drop the color and slide left while holding.
- Filling an empty layer. If the circle is on a different layer than the one you're filling, there's nothing to stop the fill. Either draw and fill on the same layer, or set the circle's layer as the Reference layer so Procreate detects the outline from it.
- An open outline. Zoom in and close any gap, then try again.
White spots or a light edge remain
This usually happens when the outline was drawn with a textured or semi-transparent brush, so the edge isn't fully opaque. Raise the threshold slightly, or redraw the outline with a solid brush. Another fix is to fill on a layer below the outline so the line covers any gap.
The color doesn't change the outline
Alpha Lock only affects the pixels already on the layer. If you want a different outline color, lock the outline layer and fill it separately from the interior.
Keep your fills organized for motion work
If you're preparing artwork for animation or compositing, a few habits save time later:
- Separate the fill and the outline onto different layers. You can animate, recolor, or track them independently.
- Use Alpha Lock rather than flattening. It preserves the shape's transparency.
- Keep flat color as flat color. A solid fill is easy to replace with a gradient or texture later, which is harder if you've already painted shading into the same layer.
For a pure vector circle that scales and animates cleanly, a shape layer in After Effects is the better tool. Procreate is raster, so a circle drawn at one size gets soft if you scale it up significantly. Use Procreate when you want hand-drawn texture, imperfect edges, or a painterly look.
Quick reference
Learn ColorDrop and its threshold first. Nearly every other fill method in Procreate is a variation on the same idea: tell the app which pixels count as inside the shape, then give it a color.