How to Fade Image in Procreate
StyleFrame Team7 min read
To fade an image in Procreate, open the layer's settings and lower the Opacity slider for a uniform fade. For a gradual fade across the image, add a Layer Mask and paint on it with a soft brush in black, white, and gray. To fade over time, use Procreate Dreams and keyframe the Opacity filter from 100% to 0% (or the reverse).
The right method depends on whether you need a spatial fade (part of the image dissolving into the canvas) or a temporal fade (the image appearing or disappearing across frames). The sections below cover each, plus how to hand the result to a compositing pipeline.
Method 1: Fade an Image with Layer Opacity
This is the fastest option and works when the whole layer should be uniformly translucent.
- Open the Layers panel and select the layer holding your image.
- Open the layer's settings.
- Drag the Opacity slider down until the image sits at the strength you want.
This is a global value. Every pixel on the layer gets the same transparency, so it can't produce a gradient. It is still useful for ghosting a reference image, knocking back a texture, or stacking several translucent layers to build density.
Opacity stays editable as long as you don't merge the layer, so you can return and adjust it. Pair it with a blend mode when you want the faded image to interact with the layers beneath it rather than just sit on top.
Method 2: Fade Part of an Image with a Layer Mask
A mask is the non-destructive way to make an image dissolve into the background. It works like covering part of the image with paper: black hides, white reveals, and gray partially hides. Nothing is erased, so you can reverse any decision.
Set up the mask
- Tap the image layer's thumbnail and choose Mask. A white mask thumbnail appears on the layer.
- Make sure the mask thumbnail, not the image, is the active target.
- Paint with black to hide areas, and with white to bring them back.
Build a gradual fade
A hard black stroke gives you a hard edge. To get a smooth falloff, use one of these approaches:
- Soft brush painting. Choose a soft brush, enlarge it, and sweep from the area you want fully hidden toward the area you want visible. Use low pressure or a low brush opacity and build up in passes.
- Fill, then blur the mask. Fill the region you want hidden with black, then go to Adjustments and apply Motion Blur while the mask is selected. Blurring the mask turns the hard black-to-white boundary into a transition. Motion Blur is especially useful when the fade should feel directional, such as an image dissolving from the bottom edge upward.
- Mid-gray for partial transparency. Painting with gray on the mask knocks the image back without removing it. A band of gray in the middle of a mask, blurred outward, produces a subtle, uneven fade that looks more natural than a clean linear ramp.
Tips for cleaner mask fades
- Work at the full canvas edge. Paint beyond the visible area so you don't leave a thin line of unmasked pixels at the border.
- Keep the blur radius proportional to the image. Too little leaves a visible band; too much washes out the area you meant to keep solid.
- If a fade looks muddy against a colored background, check what's behind the layer. A mask only reveals what's underneath, so a busy backdrop will show through a half-faded image.
- Duplicate the layer before major mask edits if you want a quick fallback, though the mask itself is already reversible.
Method 3: Fade with the Eraser (Destructive)
You can also lower a soft Eraser's opacity and brush away the edges of an image. It works, but it removes pixels permanently. If the artwork is on a single flattened layer and you've no need to revisit it, it's fine. Otherwise, a mask gives you the same visual result with an undo path that survives closing the file, so prefer it for anything client-facing.
Method 4: Fade an Image Over Time in Procreate Dreams
If you need the image to appear or disappear in an animation, use Procreate Dreams and keyframe the Opacity filter. Opacity here is a property that changes across the timeline instead of a fixed value.
Fade out
- Select your content and place the Playhead where the fade should begin.
- Tap the Playhead to open the Action menu, then choose Filter → Opacity and set it to 100%. A keyframe appears in a track beneath the content.
- Move the Playhead to where the fade should finish.
- Open the Action menu again, choose Filter → Opacity, and set it to 0%.
- Press Play or scrub the Playhead to review.
To fade in, reverse the values: 0% at the start, 100% at the end.
Fade from or to black
Put a black background behind your content, group the elements you want to fade, and keyframe opacity on the group rather than on each layer. When the group's opacity drops, the black shows through, which gives you a clean fade-to-black. Add a second keyframe at the end to fade back out.
Control the timing
- Hold before the fade. If the first keyframe sits at the very start of the clip, the fade begins immediately and may take longer than you want. Drag the keyframe later on the timeline so the frame holds on black briefly before the opacity change begins.
- Shorten the fade. Move the two keyframes closer together for a snappier dissolve, or further apart for a slow reveal.
- Check easing. Keyframes are affected by easing, so a linear fade and an eased fade feel quite different. Set the curve deliberately instead of accepting the default.
Because keyframed filters don't permanently change the original content, you can re-time or remove the fade at any point. Opacity can also be combined with other filters such as Gaussian Blur or HSB if you want the image to defocus or desaturate as it fades.
Method 5: Frame-by-Frame Fades in Animation Assist
If you're working in Procreate's Animation Assist, a fade can mean adjusting layer opacity on successive frames by hand, for example stepping a layer through 100%, 75%, 50%, 25%, and 0% across five frames. It's workable for short fades, and the step count controls the pace. For anything longer or more precise, Dreams or a dedicated compositing tool is more practical.
Choosing the Right Method
Taking Procreate Fades into a Professional Pipeline
If your Procreate artwork is headed for a compositing or editing tool, decide where each fade should live.
- Spatial fades belong in Procreate. A mask-based gradient is part of how the artwork looks. Export with transparency so the baked-in falloff comes through, and check the alpha edges once the file is over your actual background.
- Temporal fades belong in your compositor. Opacity animation is easier to refine in a dedicated compositing tool. Export the artwork on a transparent background without a baked-in time-based fade, then keyframe opacity there.
- Export at the resolution you need. Fades on low-resolution artwork can show banding in soft gradients. Work at a canvas size that holds up at your delivery resolution, and consider a touch of grain in comp to break up any banding.
Common Problems and Fixes
- The fade does nothing. You are probably painting on the image instead of the mask. Check which thumbnail is highlighted.
- A visible hard line remains. Blur the mask, or repaint with a larger soft brush and lower opacity.
- The image fades but looks gray or dirty. The background behind the layer is showing through. Change the background color or add a solid layer underneath.
- The fade in Dreams is too slow. Your first keyframe is likely at the start of the clip. Move it later, or bring the end keyframe closer.
- The edit became permanent. Merging layers or erasing flattens your options. Keep masks and opacity settings unmerged until the artwork is final.
Summary
Use the opacity slider for uniform transparency, a layer mask for gradients and directional dissolves, and Procreate Dreams keyframes for fades across time. Keep spatial fades in the artwork, and keep timing flexible by animating opacity in the tool where you'll finish the piece.