How to Edit Drawing Guide in Procreate
StyleFrame Team7 min read
To edit a drawing guide in Procreate, tap the Actions (wrench) icon, open the Canvas tab, turn on Drawing Guide, then tap Edit Drawing Guide. From that screen you can switch between 2D Grid, Isometric, Perspective, and Symmetry, adjust color, opacity, thickness, and grid size, and toggle Drawing Assist. Tap Done to commit the changes or Cancel to discard them.
Open the Drawing Guide editor
The editor is only reachable once the guide is switched on for the canvas.
- Open your canvas and tap the wrench icon in the top left to open the Actions menu.
- Tap the Canvas tab.
- Flip the Drawing Guide switch on. A faint grid appears over your artwork.
- Tap Edit Drawing Guide directly below the switch.
Procreate then zooms out to show the whole canvas so you can judge how the guide sits across the full composition. The first time you use a guide on a canvas, it defaults to the 2D Grid. After that, Procreate remembers the settings you last used on that canvas.
The guide features need Procreate 4.1 or later. Earlier versions only had a standalone perspective guide. If the options below are missing on your device, check your version first.
What each control does
The editor has a short list of controls. Knowing what each one changes saves you from trial and error.
Color
The color slider along the top sets the color of the guide lines. Pick something that contrasts with your artwork but won't compete with it. A pale blue or pink at low opacity is easy to read without dominating the canvas.
Opacity and thickness
These sliders at the bottom control how visible the lines are. For a reference you only glance at, drop opacity low and thin the lines. For precise alignment work, raise both so you can see exactly where strokes will snap.
Grid size
This applies to the 2D Grid and Isometric modes. Drag the slider, or tap the numeric readout and type an exact value. Exact values are useful when you want the grid to match a specific unit, such as a 60 px module, or to divide a canvas evenly for layout.
Assisted Drawing toggle
This switch controls Drawing Assist, which snaps your strokes to the guide. With it off, the guide is just a visual overlay and you draw freehand. With it on, strokes follow the guide's logic: horizontal and vertical on a 2D Grid, horizontal and diagonal on an Isometric grid, and toward vanishing points on a Perspective guide.
Done and Cancel
Done commits your edits and returns you to the canvas. Cancel throws away what you changed in this session. If you tweak several settings and lose track, Cancel is a quick reset to the last committed state.
Switch between guide types
The four buttons under the canvas in the editor select the guide mode:
- 2D Grid: a square grid for flat shapes, alignment, and spacing.
- Isometric: a triangular grid for technical or architectural illustration without foreshortening.
- Perspective: a vanishing-point guide for one-, two-, or three-point perspective, useful for environments and backgrounds.
- Symmetry: a mirroring guide that works with Drawing Assist for reflected, tiled, or radial designs.
Each mode keeps the shared appearance controls, but some add their own options, covered below.
Edit a perspective guide
Perspective is the mode where editing is most hands-on, since you place the geometry yourself.
- Add a vanishing point: tap on or outside the canvas area. You can set up to three points, which gives you one-, two-, or three-point perspective.
- Move a point: drag it to a new position. Dragging a vanishing point beyond the canvas edge is how you get gentle perspective for wide establishing views.
- Delete a point: tap an existing point to bring up a menu, then choose delete.
- Adjust the lines: use the thickness and opacity sliders, and the color bar for contrast against your artwork.
For concept art that will later become a camera move, the horizon and vanishing point placement effectively define your camera height and angle. Spend a minute getting these right before you commit to line work.
Edit a symmetry guide
Symmetry mode adds options for how strokes mirror:
- Vertical and Horizontal mirror across a single axis.
- Quadrant mirrors across both axes, giving four sections.
- Radial repeats strokes around a center point.
- Rotational symmetry makes the mirrored marks follow the rotation direction.
Symmetry only takes effect with Drawing Assist on, so if nothing is mirroring, check that toggle first.
Make sure Drawing Assist is active on the layer
This is the most common source of confusion. Drawing Assist is applied per layer. After you set up a guide, the layer you draw on needs to show the Assisted label under its name in the Layers panel. If it doesn't, strokes will ignore the guide even though the grid is visible.
To toggle it on a specific layer, tap the layer once to open Layer Options, then tap Drawing Assist.
You can also reach Drawing Assist without reopening the guide editor:
- Assign it to a QuickMenu slot.
- Map it to a gesture under Actions > Prefs > Gesture Controls, using touch, Apple Pencil, or the Modify button.
This matters because turning the main Drawing Guide switch off doesn't automatically turn assistance off on layers that have it enabled.
Troubleshooting common problems
Every stroke is perfectly straight. Drawing Assist is probably still enabled on one or more layers. Check each layer for the Assisted label and toggle it off in Layer Options. Also check any QuickMenu or gesture assignments you may have triggered by accident. If it persists, restarting the iPad and reopening the file can clear a stuck state.
The guide isn't visible. Confirm the Drawing Guide switch is on in Actions > Canvas, then open the editor and check that opacity isn't set near zero or the color blending into your background.
The grid is too big or too small. Open Edit Drawing Guide and adjust Grid Size. Type an exact number if you need a specific module.
No perspective or symmetry option. Update Procreate. These modes arrived with the Drawing Guide tool in version 4.1.
Strokes don't snap to the grid. Check the Assisted Drawing toggle inside the editor and the Assisted label on the layer.
A practical setup for motion and animation prep
Many motion designers use Procreate for fast boards, style explorations, and layout sketches before moving to After Effects, Cinema 4D, or Blender. The guide editor is handy for that stage if you set it up deliberately:
- Match the frame ratio. Create the canvas at your delivery aspect ratio so thirds, centers, and safe areas line up with the grid.
- Use a grid size that divides evenly. An exact value that divides your canvas width gives you reliable alignment for title placement and graphic elements.
- Set a perspective horizon for camera planning. Placing vanishing points consistently across a sequence of boards keeps camera height and lens feel coherent from frame to frame.
- Keep guides light. Low opacity and thin lines stop the guide from distracting while you evaluate composition.
- Separate guided and freehand layers. Use Drawing Assist on structural layers like architecture or props, and leave organic layers unassisted.
Guides are canvas overlays rather than painted pixels, so they shouldn't end up in your artwork. Still, export a quick test frame before you hand off boards to confirm nothing unexpected is baked in.
Quick reference
Once you know the path (Actions, Canvas, Edit Drawing Guide), the rest is a handful of sliders and one critical per-layer toggle. Get those right and the guide stays out of your way until you need it.