How to Drop Paint in Procreate
StyleFrame Team7 min read
To drop paint in Procreate, drag the color circle from the top right of the screen into a closed shape and release. To control how far the fill spreads, keep your finger or Apple Pencil on the screen after the color floods in, then slide left or right to change the ColorDrop Threshold before you lift. If the color floods the whole canvas, close any gaps in your line work, lower the threshold, or check whether another layer is set as a Reference layer.
What "Drop Paint" Means in Procreate
Procreate's official name for this feature is ColorDrop. It works like a paint bucket, except you drag the color into place instead of selecting a bucket tool. The fill follows the pixels on the active layer (or on a designated Reference layer), so the quality of the result depends on how clean your edges are.
For motion designers, this is the fastest way to lay flat color under line art, block in silhouettes for character or shape-layer work, or prep clean mattes and style frames before they go into After Effects.
Step-by-Step: Using ColorDrop
- Pick your color. Tap the color dot at the top right and choose a swatch or hue.
- Make sure the shape is closed. Any gap, even a few pixels wide, lets the fill escape.
- Drag the color dot into the shape. Press the dot, drag it onto the canvas, and hold it over the area you want to fill.
- Keep holding for a beat. A blue Threshold bar appears at the top of the canvas with a percentage readout.
- Slide to adjust. Moving right makes the fill more aggressive, and moving left makes it less so. You don't need to touch the bar itself. Any horizontal movement works, as long as you never lift.
- Lift to commit. The fill applies at the Threshold you stopped on.
Procreate remembers your last Threshold setting, so a value that worked on one shape will carry over to the next. This is also why a fill can suddenly misbehave. If you left the Threshold at a high value, the next drop may flood far more than you expected.
Drag from the Palette Too
You can also drag a swatch from a floating color palette. That helps when you're filling with a color that differs from your active one, and it saves you from switching colors back and forth.
Fill Several Areas Fast with Continue Filling
After a ColorDrop, a Continue Filling option appears at the top of the screen. Tap it, and each following tap on the canvas fills that area with the same color. You can also tap, hold, and drag to adjust the Threshold for that particular fill.
To exit, tap the checkmark or switch to another tool such as the Paint brush. If your Apple Pencil supports hover, you can hover over the active color dot and double-tap the side of the Pencil to jump straight into Continue Filling with that color.
This is the right mode when you're blocking in a dozen shapes of the same color, such as a repeated pattern element or a set of background shapes.
Fill on a Separate Layer with a Reference Layer
Filling on the same layer as your line art is quick, but it mixes color and lines together. For anything headed into a compositing pipeline, keep them separate:
- Put your line art on its own layer.
- Open the Layers panel and tap the line art layer's thumbnail to open Layer Options.
- Turn on Reference.
- Create a new layer underneath and select it.
- Use ColorDrop on the new layer. The fill follows the line art in the Reference layer, but the paint lands on the layer you're working on.
With this setup you can recolor or replace fills later without touching the lines.
Why ColorDrop Fills the Entire Canvas
This is a common complaint. Work through these causes in order:
- The shape isn't closed. Zoom in and look for tiny gaps, especially where strokes meet. A fast fix is to draw a short line across the gap on the line art layer.
- The Threshold is too high. Drop the color, hold, and slide left until the fill stays inside the shape. A Threshold near 100% will flood almost anything.
- Another layer is set as Reference. If any layer, even one in a different group, has Reference enabled, ColorDrop reads from it instead of the layer you're on. Disable Reference on layers you aren't using for that purpose. Several users report this fixes their "nothing works" cases.
- Line art is split across several layers. If your outlines live on multiple unmerged layers, the fill may not see a sealed shape. Merge the outline layers, or consolidate them into one Reference layer.
If the fill does nothing at all, and you don't even see the color dot lift off when you drag, force-close and reopen Procreate. Users report intermittent drag-and-drop failures that clear up after a restart, particularly after filling a blank layer with one color and then trying another.
Dealing with Textured Brushes and Soft Edges
ColorDrop fills pixels, so a grainy chalk or charcoal outline has tiny holes and light patches. The fill may stop short of the stroke edge and leave a halo of unfilled pixels.
To reduce this:
- Raise the Threshold slowly while holding, nudging it up one percentage point at a time until the gaps close.
- Draw a clean, solid-edged version of the shape on a separate layer to use as the Reference.
- Fill slightly beyond the line and let the textured outline layer sit on top. Keep fills below line art in the layer stack.
Even then, expect some mismatch between a hard-edged fill and a textured stroke. That's a property of the technique, not a setting you've missed.
Other Ways to Fill Color in Procreate
ColorDrop isn't the only route. Depending on the job, one of these may be faster.
Recolor
Recolor is an older tool that Procreate brought back. It's hidden unless you turn on QuickMenu under Actions → Prefs → Gesture Controls → QuickMenu. Assign Recolor to one of the radial slots, select your color, tap the areas to fill, and adjust the Flood slider to control how far the fill spreads.
Selections with Color Fill
Open Selections, choose a method (Automatic, Freehand, Rectangle, or Ellipse), and turn on Color Fill. Each time you complete a selection, it fills with the current color automatically. This is useful for geometric shapes and hard-edged masks. Two cautions: the setting persists until you switch it off, and it only works on a single layer, not a group.
Fill Layer
Choose a color, open Layers, tap the layer to open Layer Options, and select Fill Layer. The whole layer fills with that color. It's a quick way to make a solid background or a flat color base that you'll mask or paint over later.
Preparing Procreate Fills for a Motion Pipeline
Flat color blocking in Procreate often serves as the first step before animation or compositing. A few habits make the handoff cleaner:
- Keep fills, lines, and shadows on separate layers. Clean separation means you can toggle, blur, or recolor each in your compositor.
- Name your layers before export. Clear layer names make a layered file easier to rebuild in your compositor than a flattened image.
- Fill slightly under the line art. Overlap prevents hairline gaps when you scale or move elements.
- Work at your target resolution. Upscaling flat fills later can soften edges, so set canvas size to match your delivery frame or larger.
Quick Troubleshooting Checklist
- Fill floods everything: check for gaps, lower the Threshold, and disable stray Reference layers.
- Threshold bar never appears: keep one finger or the Pencil in continuous contact after the color lands. Don't lift or use a second hand on the bar.
- Fill leaves unpainted edges: raise the Threshold slightly, or fill beneath the line layer.
- Nothing happens when you drag: restart Procreate and try again.
Final Thoughts
Dropping paint in Procreate comes down to three things: a closed shape, a sensible Threshold, and awareness of which layer is acting as Reference. Once those are in place, ColorDrop and Continue Filling make flat-color work quick, and a separate fill layer keeps the file flexible for animation, compositing, and any AI-assisted step that follows.