How to Drop Opacity in Procreate
StyleFrame Team5 min read
To drop opacity in Procreate, open the Layers panel, tap the "N" beside the layer, and drag the Opacity slider to the left. A quicker route is to tap the layer with two fingers and slide your finger left on the screen. To make a brush paint more transparently, drag the lower slider on the left sidebar down instead.
Procreate has three places where opacity lives: the brush, the layer, and a selection. Each behaves differently, and knowing which one you're changing saves a lot of confusion.
The three kinds of opacity in Procreate
- Brush opacity controls how transparent new strokes are. It doesn't change anything already on the canvas.
- Layer opacity controls the visibility of an entire layer. It's non-destructive, so you can change it as often as you like.
- Selection opacity changes only the selected pixels on a layer. It is applied when you exit the mode, so treat it as destructive.
How to drop layer opacity
Layer opacity is what most people want, and there are two ways to reach it.
Method 1: the "N" menu
- Tap the Layers icon in the top right.
- Tap the small letter to the right of the layer name. It reads "N" by default, for Normal blend mode.
- Drag the Opacity slider to the left to reduce it. The percentage is shown beside the slider.
This menu also holds the blend modes, so it's the better choice when you're adjusting both at once. Setting a layer to Multiply at 60%, for example, is a common way to build soft shadows.
Method 2: the two-finger tap
- Open the Layers panel.
- Tap the layer with two fingers at once. Index and middle finger of one hand work well.
- A slider appears at the top of the screen. Slide left to lower opacity, right to raise it.
The percentage appears next to the word "Opacity," so you can land on exact values. You can use a finger or an Apple Pencil. Only one layer can be adjusted at a time, so group layers first if you want to fade several together.
Fading several layers together
Select the layers and put them in a group. Then change the opacity on the group itself using the same "N" menu or two-finger tap. This is also how you keep a character's linework and color on separate layers while still fading the whole character as one object.
How to drop brush opacity
- Select the brush you want to use.
- Find the two sliders on the left sidebar. The top one is size, the lower one is opacity.
- Drag the lower slider down to reduce opacity, and up to increase it.
If your brush looks too faint even with the slider at maximum, check Apple Pencil pressure. Many brushes tie opacity to pressure, so a light touch gives a lighter stroke.
Brush opacity is useful for building up tone gradually, as with soft shading, glazing, or smoky effects. Painting several light passes gives you more control than one heavy pass.
How to drop opacity on a selection
This is the least obvious method, and the one most likely to catch you out.
- Open Selections and choose a method, such as Automatic.
- Make your selection.
- Open the Layers panel.
- Tap the layer containing the paint with two fingers at once.
- Slide a finger left on the canvas to reduce the opacity of the selected area, or right to raise it.
When you leave this mode, the change is applied to the pixels. You can undo it right away, but you can't revisit it later the way you can with a layer slider. If you might want a different value tomorrow, move the selection onto its own layer first and adjust that layer's opacity.
Using Adjustments > Opacity
Older versions of the Procreate Handbook describe an Opacity tool under the Adjustments menu. It works on the active layer. A bar at the top of the screen reads "Slide to adjust," starting at 100%, and you slide left to make the layer more transparent. Buttons at the bottom let you cancel, undo, redo, or reset. Tapping the Adjustments icon again or choosing another tool commits the change.
Your version may arrange this differently, so if the menu looks different, the Layers panel methods above are the dependable route. Like selection opacity, anything committed this way is baked into the pixels.
Destructive vs. non-destructive: a quick comparison
For animation and production work, default to layer-level opacity. It leaves your options open when a director changes their mind.
Why opacity sometimes looks wrong
A few common causes of "my opacity isn't doing what I expect":
- Pressure sensitivity. The brush opacity slider may be at 100%, but light pressure still produces translucent strokes.
- Blend mode. A layer set to anything other than Normal can look faded or tinted even at 100% opacity. Check the "N" menu.
- Clipping masks. A layer clipped to the one below only paints where that layer has pixels. This can look like an opacity problem when it's really a masking one.
- Fills with unexpected transparency. If a fill such as Color Drop comes out see-through, check the layer's opacity and blend mode first. In a Procreate support thread on this exact problem, staff asked what the layer's opacity was set to and then requested the canvas file for inspection.
- Selection opacity applied earlier. A previous selection-based opacity change may have left some pixels semi-transparent. Because it's destructive, the slider won't show it.
Quick reference
- Layer opacity: Layers > tap "N" > Opacity slider, or two-finger tap the layer.
- Brush opacity: lower slider on the left sidebar.
- Selection opacity: make a selection, two-finger tap the layer, slide on the canvas.
- Non-destructive choice: layer or group opacity.
- If it still looks wrong: check pressure, blend mode, clipping masks, and earlier destructive changes.
Once you know which of the three opacity types you're changing, it takes only a few seconds, and it's worth building the habit of using layer-level opacity wherever you can.