How to Drop Fill Procreate
StyleFrame Team7 min read
To drop fill in Procreate, drag your active color from the circle in the top right corner into a closed shape on your canvas, then release. ColorDrop floods the area until it hits an outline. If the color spills across the whole canvas or leaves gaps, drag the color in again but don't lift your finger or Pencil: pause until the blue Threshold bar appears, then slide left to fill less or right to fill more before you release.
How to use ColorDrop step by step
ColorDrop is Procreate's bucket-fill tool. It's faster than painting with a large brush, and it can fill an area more completely.
- Select the layer you want to fill. By default, ColorDrop reads the pixels on the active layer, so the outline and the fill target need to be on the same layer unless you set up a Reference layer (covered below).
- Pick your color. The active color swatch sits in the top right corner of the interface.
- Drag the swatch into the shape. Touch the swatch with your finger or Apple Pencil and drag it over the area to fill. You'll see the color flood in as you hold.
- Release to commit. Lifting your finger sets the fill.
- Undo if needed. A two-finger tap undoes the fill, so you can retry with different settings.
You can also drag a color directly from a floating Color panel, which is handy when you're filling with colors that differ from your line work.
How to adjust the ColorDrop Threshold
Threshold is the setting that most often causes trouble. It controls how much of an area the fill is allowed to flood, and Procreate remembers the last value you used. If a previous fill pushed Threshold to 100%, your next fill may flood the entire layer even though your shape is perfectly closed.
To adjust it:
- Drag the color over the shape you want to fill.
- Keep contact with the screen. Don't lift.
- Hold briefly until a thin blue bar with a percentage appears along the top of the canvas.
- Slide left to decrease the Threshold (fill less) or right to increase it (fill more). You don't need to touch the bar itself; the movement can happen anywhere on the screen.
- Lift to commit once the fill looks right.
A few practical notes:
- Use one hand and one input, either a finger or the Pencil. Breaking contact at any point cancels the adjustment, which is a common reason people think the slider is broken.
- Move slowly when working with textured brushes. Small percentage increments let you close tiny gaps without flooding past the line.
- Remember that the setting persists. If a fill behaves oddly on a new piece, check the Threshold first.
How to fill on a separate layer with a Reference layer
Keeping line art and color on separate layers is a cleaner production habit for many artists. Procreate supports it through the Reference feature.
- Open the Layers panel.
- Tap the thumbnail of your line art layer to open Layer Options.
- Tap Reference.
- Select a new, empty layer beneath the line art.
- Drag your color into a shape. ColorDrop now reads the outline from the Reference layer but paints onto your active layer.
This keeps your lines untouched, lets you recolor fills without redrawing anything, and makes it easy to hide or export the layers independently. If you work on a multi-layer character with several line layers, merge the outlines you want ColorDrop to read into a single layer first. Unmerged outline layers can cause the fill to behave as if the shapes are open.
Troubleshooting: why ColorDrop isn't working
Most ColorDrop problems come down to a handful of causes. Work through these in order.
The fill covers the whole canvas
- There's a gap in your line. Even a small break lets color escape. Zoom in and check corners, junctions, and the ends of strokes. Closing the gap with a quick brush stroke usually solves it.
- Threshold is too high. Redo the drop and slide the Threshold lower before releasing.
- A different layer is set as Reference. This is a frequent culprit. If any layer, even one tucked inside another group, still has Reference enabled, ColorDrop reads from it instead of your active layer. Open the Layer Options for each layer and turn Reference off where you don't need it.
- Outline layers aren't merged. If your shape is bounded by lines from two different layers, merge them or use a single Reference layer.
The fill leaves gaps or a rough edge
- Textured brushes. Grainy or chalky strokes have uneven edges, so the fill stops short in places. Raise the Threshold gradually. Expect some mismatch between a solid fill and textured lines, because that's inherent to the method.
- Anti-aliasing. Some artists find Procreate less precise than dedicated inking tools for flatting because it lacks a gap-closing option and works with anti-aliased edges, so plan on tidying edges manually.
The Threshold slider won't move
- Make sure you're holding continuously after the color floods in. Lifting, or switching between finger and Pencil mid-drag, resets the gesture.
- Wait for the blue bar and percentage to actually appear before you slide.
Nothing happens when you drag the color
- Check that the color swatch is actually being picked up. You should see it follow your finger.
- If the drag fails intermittently, closing the app and reopening it has fixed it for some users. Make sure Procreate and iPadOS are up to date. If the issue persists after an update, contact Procreate support with your device model and version numbers.
Tips for fills that hold up in production
For motion and animation work, fill quality matters because small flaws become visible when they flicker across frames or get composited over other elements.
- Use hard-edged brushes for line art you plan to fill. Monoline-style brushes tend to fill more cleanly than textured brushes.
- Fill below the line layer. Put color on its own layer under the outlines so a slightly loose fill tucks behind the lines.
- Name your layers. If the file is heading to After Effects, clear names like "skin," "hair," and "line" save time when you import a layered file.
- Keep flat colors flat. Don't add shading on the same layer as the base fill. Separate layers give a compositor matte-like control later.
- Check at full zoom before export. Look for stray pixels and unfilled islands inside shapes, especially around eyes, fingers, and any small enclosed areas.
Taking Procreate fills into a motion pipeline
Procreate is a strong place to build character art, style frames, and flat-color keyframes quickly. From there, the work can move into motion software for animation and finishing.
A practical sequence might look like this: draw and fill your key poses in Procreate using ColorDrop and a Reference layer, export them as clean PNGs, then bring them into your compositing or animation software for color, compositing, and final delivery.
Quick reference
Once you understand that ColorDrop depends on three things, a closed outline, a sensible Threshold, and the right Reference layer, it becomes one of the fastest ways to flat-color artwork in Procreate. From there, the fills are ready to carry into whatever motion pipeline you're building.