How to Draw Wood in Procreate
StyleFrame Team7 min read
To draw wood in Procreate, fill a layer with a warm brown base, run Adjustments > Noise > Clouds to break up the flat color, then paint grain lines along one consistent direction with a textured brush. Build knots, cracks, and color variation on separate clipped layers, then finish with Multiply and Overlay blends for depth. For motion work, paint at a high resolution, export a PNG or PSD, and test the result as a tiled texture or reference frame in After Effects.
Set Up the Canvas for Motion Work
One popular beginner tutorial uses a small square canvas of 1000 × 1000 px, which is fine for learning but too soft for video. If the wood will sit behind animation in a 4K comp, work larger. Choose a canvas that leaves room for the layers you plan to use.
Before painting, decide what the wood is for:
- A flat texture or background (floor, tabletop, title card backdrop): a square or 16:9 canvas works, and you should plan for tiling.
- A painted object (fence, crate, signboard): use the aspect ratio of your final frame and leave room around the subject.
- A reference or style frame: match the delivery aspect ratio so it drops straight into your timeline.
Check the canvas color profile in Procreate's canvas settings and match it to your After Effects project's color management. Mismatched profiles can make a brown look different once it lands in the comp.
Step 1: Lay Down the Base Color
Create a new layer and fill it with a mid-tone brown. A saturated, slightly reddish brown (one tutorial uses a hex near #9B2F12) gives you room to go both darker and lighter. A dull, desaturated brown tends to turn muddy once you add shadows.
Drag the color swatch onto the layer to fill it. Keep this layer clean, because it is your color foundation. Everything else goes above it on clipped layers so you can change the species or stain later without repainting.
Step 2: Break Up the Flat Fill with Noise
With the base layer selected, open Adjustments > Noise and choose the Clouds option. A modest strength (around 25%) with a scale suited to your canvas adds irregular light and dark patches, which mimics the uneven density in real timber.
Next, stretch that noise in the direction of the grain. Use Adjustments > Motion Blur (Directional) at a low-to-moderate strength and set the angle to match your planks. Wood grain runs in long, mostly parallel fibers, and a directional blur is a fast way to get that streaky character before you paint a single line.
Step 3: Block In Planks and Grain Direction
Decide the layout before you draw detail. For planks, sketch dividing lines freehand on a new layer rather than using a ruler. Slightly wobbly edges and small differences in plank width read as more natural than perfectly even boards.
Then establish the grain:
- Create a clipping mask layer above the base.
- Pick a darker brown and a brush with some bristle or grain texture. The default Painting set has usable options, and a dry or grunge-style brush works well.
- Pull long strokes along the length of each plank. Vary pressure and speed so lines thicken and thin.
- Let some strokes drift and converge slightly. Real grain bends around knots and growth rings.
Avoid drawing every line. Suggest the pattern in a few passes and let the noise from Step 2 do part of the work. Over-drawn grain looks like a pattern stamp.
Step 4: Add Depth with Light and Shadow Layers
Create a new layer set to Multiply for shadows and another set to Overlay or Soft Light for highlights. Both should be clipped to the wood.
- On the shadow layer, darken the edges of planks, the gaps between boards, and the area under any overhangs.
- On the highlight layer, brush a lighter warm tone along the lit edge of each plank and across the top of the composition where your light source falls.
- Lower layer opacity instead of using timid brush pressure. That way you can adjust the whole effect in one move.
If you are painting an object like a fence instead of a flat surface, this is where you define large masses of light and shadow first, then add texture. Establishing the big value shapes before the fine grain keeps the form readable.
Step 5: Paint Knots, Cracks, and Wear
Details sell the material. Keep them on their own layers.
- Knots: Paint a darker oval, then wrap grain lines around it in concentric curves. A small highlight on one side helps it sit in the surface.
- Cracks: Use a thin, hard brush with a dark color, then add a light edge on one side so the crack has thickness.
- Nail holes or dents: Small dark dots with a subtle highlight below are enough.
- Weathering: On older wood, add desaturated gray and cooler greens in patches, and erase parts of the grain with a soft eraser to simulate worn finish.
Fresh lumber and aged wood differ mostly in color variation and edge wear. Painting both versions of the same plank is a good exercise, and it gives you two variants to cross-fade later in a comp.
Step 6: Push Color with Gradient Maps and Blend Modes
Procreate's Gradient Map adjustment lets you recolor the whole texture based on its luminance. Apply it on a flattened copy or a grouped duplicate, build a gradient from dark brown through orange to pale tan, and you can turn the same grain into oak, walnut, or bleached driftwood without repainting.
Useful finishing moves:
- Add a Multiply layer with a faint, warm gradient to unify the lighting.
- Use an Overlay layer with low-opacity color to push mood (cooler for night scenes, warmer for interiors).
- Add subtle Noise at the very end so the surface does not look too smooth when scaled up.
Make the Wood Tileable
If the wood will fill a large area or scroll, it needs to repeat without a visible seam. One approach is manual:
- Duplicate the flattened texture.
- Shift the copy by half the canvas width and height so the original seams sit in the center.
- Paint or erase through the middle to blend the join, matching grain direction.
- Merge and repeat the check.
You can test tiling quickly in After Effects with the Motion Tile effect. Stack a few repeats and look for obvious repeating knots or highlights. Those are the giveaways, so vary or remove them.
Bring It into After Effects and 3D Tools
Export from Procreate as PNG for a flattened image, or PSD if you want to keep layers. A layered PSD lets you separate grain, highlights, and color in your comp.
Practical uses:
- After Effects: Use the wood as a background, a texture on a precomp, or a luma source. Convert a desaturated copy with Levels and use it as a displacement or bump-style map for subtle surface relief with effects like Displacement Map or CC Bump Map.
- Cinema 4D and Blender: Plug the color layer into a base color channel. Make a grayscale copy, adjust its contrast, and use it for roughness or bump. Painted textures won't carry physically accurate data, so treat them as art-directed rather than scanned.
- Nuke: Bring the PNG in as a Read node and use it for card textures, projections, or matte painting elements.
Keep an untouched, layered Procreate file. When a client changes the wood tone from honey to ebony, you'll want to change a Gradient Map rather than repaint.
Common Mistakes to Avoid
- Grain running in different directions on the same plank. Pick one direction and bend it only around knots.
- Too much contrast in the grain. Real wood grain is often subtle. Lower opacity before adding more strokes.
- Single-layer painting. You lose the ability to retint or adjust. Clip everything.
- Ignoring scale. Large, heavy grain on a small prop looks wrong. Match grain size to the real object.
- Skipping the tile check. A repeating knot is obvious in motion.
Quick Recap
Start with a saturated brown base, add Clouds noise, stretch it with directional blur, paint long grain strokes on clipped layers, and add shadow and highlight layers. Finish with knots, wear, and a Gradient Map for color flexibility. Then export at a resolution that holds up in your comp and test the tiling before you animate.