How to Draw Underneath a Layer in Procreate
StyleFrame Team7 min read
To draw underneath a layer in Procreate, select the layer that sits directly below the one you want to work beneath, then tap the plus icon. Procreate always adds new layers above the active one, so the new layer lands in the right spot. If there is nothing below, or the new layer ends up in the wrong place, press and hold it in the Layers panel and drag it under the target layer. Procreate has no "Behind" paint mode, so painting behind pixels on the same layer takes a short workaround, covered below.
Method 1: Select the layer below, then add a new layer
This is the fastest route and needs no dragging.
- Open the Layers panel (the two stacked squares in the top toolbar).
- Tap the layer that sits beneath the layer you want to draw under. It highlights as the active layer.
- Tap the + icon. A new empty layer appears directly above the active one, and therefore directly beneath your target layer.
- Draw on it. Whatever you paint shows through only where the layers above are transparent.
For example, with a character on "Layer 3" and a rough sketch on "Layer 2", select Layer 2 and tap +. The new layer sits between them, so you can paint a color flat behind the character without touching the line work.
Method 2: Drag an existing layer under another
If you've already created a layer in the wrong place, reorder it.
- Press and hold the layer in the panel until it lifts slightly.
- Drag it down past the layer you want it to sit beneath.
- Release when a thin gap opens in the right position.
Dragging also works for existing layers you want to push behind something else, such as moving a texture layer under your line art. You can select several layers by swiping right on each one and then drag them together.
What happens at the bottom of the stack
Procreate's Background color layer is pinned to the bottom. You cannot move a layer below it, and you cannot draw on it. This is usually what you want, but it affects two situations:
- You want to draw under your lowest layer. Add a new layer and drag it below that layer. It will stop just above the background color, which is fine.
- You need transparency. Toggle the Background color off before exporting, or your export may carry a solid fill. This matters a lot if the art is headed for a compositing timeline.
Draw behind pixels on the same layer
Photoshop and other tools offer a "Behind" blend mode that paints only into empty areas of a layer. Procreate doesn't. These are the practical equivalents, from most to least recommended.
Option 1: Move the work to its own layer
Paint on a separate layer beneath. This is the most flexible approach because you can adjust opacity, blend mode, or position independently later. If you really need a single flattened layer, use Merge Down at the end. The stacking order is preserved in the merge.
Option 2: Select the layer, invert, and paint
When you must keep everything on one layer:
- Tap the layer and choose Select. This selects the opaque pixels on that layer.
- In the selection toolbar, tap Invert.
- Paint on the same layer. Strokes only land in the unselected, formerly empty area.
Expect slightly soft edges where anti-aliased pixels meet the selection. For clean cel-style art, you may see a thin fringe. Feathering or a small amount of overlap helps. If the fringe bothers you, fall back to Option 1.
Option 3: Duplicate, Alpha Lock, and offset for outlines and shadows
To create an outline, sticker border, or drop shadow behind a shape:
- Duplicate the shape layer.
- Turn on Alpha Lock for the lower duplicate (swipe right with two fingers on the layer, or use Layer Options).
- Fill it with your outline or shadow color.
- Optionally apply Gaussian Blur or nudge it with the Transform tool.
Alpha Lock keeps the fill inside the existing pixels, so the duplicate keeps the shape's silhouette. Use the Transform tool to enlarge it for a border.
Option 4: Clipping masks for constrained shading
A clipping mask works the opposite way. It restricts paint on a layer to the pixels of the layer below. Add a layer above your base shape, tap it, choose Clipping Mask, and paint without spilling over the edges. Use this for shading and texture on top, and use the techniques above for anything that must sit behind.
Habits that prevent stack confusion
Drawing in the wrong layer is the most common problem in layered work. A few habits cut down on it:
- Name layers as you create them ("BG sky," "Character lines," "Shadow"). Tap the layer and choose Rename.
- Group related layers. Swipe right to select several layers and tap Group. This is especially important if you intend to move the file into a compositing app.
- Lock finished layers. Tapping the layer and choosing Lock stops accidental strokes, which is handy when you're working under a layer you've already refined.
- Set a Reference layer for line art. Using Reference lets you color-fill on a layer beneath without moving the active selection into the line art.
- Lower layer opacity temporarily to see what's under a layer when sketching in a tight spot, then restore it.
The number of layers you can add is limited by your device and your canvas, so plan resolution against complexity before you start.
Taking layered Procreate art into After Effects
If you're a motion designer, the reason to care about layer order is that it becomes your stacking order in the comp. Layered exports can be brought into After Effects, but check how your layers and blend modes come through.
A few checks before you export:
- Hide the background color if you need alpha.
- Match canvas size to comp size or an even multiple, so scaling doesn't soften your lines.
- Keep layer names unique and descriptive. Names like "Layer 14" are painful to find in a dense comp.
- Flatten what doesn't need to move. If a background will remain static, merge it. Keep separate only what you'll animate.
- Test one layer first. Blend modes and certain brush behaviors can look different in After Effects. Confirm before you export a 40-layer file.
Under-layers are often the pieces you animate separately, like a shadow, a color flat, or a texture behind line work. Drawing them on their own layers from the start means you won't need to cut them out later in After Effects.
Where Styleframe fits in this workflow
Procreate is good for the hand-drawn part: building key art, style frames, and layered elements. Styleframe is an AI video and motion tool that can be used alongside that work. It doesn't replace the layer work above. Features, output formats, and integrations vary and change over time, so check Styleframe's current documentation before building a pipeline around them. Your compositing workflow can stay the same, with Procreate for drawing and After Effects or Nuke for the final comp.
Troubleshooting
The new layer appears above my target layer. You had the wrong layer selected. Drag the new layer down, or delete it, select the layer below the target, and add again.
I can't move a layer below the background. That's by design. Hide the Background color and use a layer as your base instead.
My strokes aren't appearing. Check whether the active layer is locked, hidden, or has opacity at zero. Also confirm that you haven't left Alpha Lock or a clipping mask on.
Painting under the layer covers parts of my line art. The new layer is probably above the line art. Check the panel order and drag the new layer beneath it.
Edges look jagged after using Select and Invert. Anti-aliased pixels don't select cleanly. Switch to a separate layer beneath, or enlarge your underpaint so it overlaps the edge.
Quick reference
The key idea is that Procreate adds layers above the active one, so selection determines placement. Select the right layer first, and drawing underneath becomes a two-tap action.