How to Draw Trees Procreate
StyleFrame Team7 min read
To draw a tree in Procreate, sketch a tapering trunk and branch structure on its own layer, block in the foliage as three or four overlapping masses instead of individual leaves, then shade those masses with a dark, mid, and light green on separate layers. Finish with a textured brush for leaf detail and a few trunk highlights. Keep trunk, branches, foliage, and shadows on separate layers, so the drawing can be exported and animated later.
Set Up the Canvas and Brushes
You don't need a large custom brush library. A few built-in tools are enough:
- A hard pencil or pen for the structural sketch, such as a Procreate sketching pencil or the Studio Pen from the Inking set.
- A textured brush for foliage and bark. A dry brush or an organic brush from the default sets works. Some artists even use a plain square brush for leaves, which shows that brush choice matters less than how you place marks.
- A soft round brush for atmospheric haze and glow.
For canvas size, work larger than you think you need. If the tree will end up in a video comp, start at or above your delivery resolution, such as 3840 × 2160 px, so you aren't enlarging pixels later. Keep the color profile consistent with your video pipeline (sRGB is the usual choice).
Pick your palette before drawing. Three greens (dark, mid, light), two or three browns, and one accent color for light, such as a warm yellow, is plenty. Save them as a palette so every session uses the same values.
Step 1: Sketch the Gesture and Trunk
Start with the overall shape. Before any detail, draw one loose line for the tree's gesture: does it lean, fork low, or rise straight? A tree that looks "off" usually has a stiff, perfectly vertical trunk.
On a new layer, set your sketching pencil to around 70% opacity. You can build up confident lines by going over them again, so there's no need to erase every wobble.
Key trunk habits:
- The trunk should be wider at the base and flare slightly where it meets the ground.
- Add a few angled, uneven lines along the trunk to suggest bark direction.
- Avoid perfectly parallel edges. Real trunks bulge and narrow.
Step 2: Build Branches That Taper
Branches are where most beginner trees fall apart. The reliable method is to draw each branch as a stroke that starts thin and ends thick, working back toward the trunk. If your brush has pressure sensitivity, you can also draw from the trunk outward and release pressure as you go. Either way, the branch should be thickest where it joins and finest at the tip.
Rules that make branches read as natural:
- Branch from the trunk at varied heights. Don't place them in matching pairs.
- Split into smaller branches at a consistent angle, but vary the lengths.
- Place some branches in front of the trunk and some behind. This overlap adds depth immediately.
- Leave gaps. Sky showing through the branches (negative space) makes foliage feel airy rather than like a lollipop.
Put the branches on their own layer, or at least separate the back branches from the front ones if you plan to animate the tree.
Step 3: Color the Trunk
Create a new layer above your sketch and fill the trunk with a mid-brown. A useful trick is leaving the sketch layer visible underneath at reduced opacity. The pencil lines show through as built-in texture and shading, so even a flat fill looks less sterile.
Then use Alpha Lock or a Clipping Mask to add shading without painting outside the shape:
- Add a darker brown on the side away from your light source.
- Add a warmer, lighter tone on the lit side.
- Run a textured brush down the trunk following its growth direction.
Decide your light direction now and keep it fixed. Every shadow in the finished tree should be consistent with it.
Step 4: Block In the Foliage
Don't draw leaves one by one. Think in masses.
- Create a new layer and use your mid green to place 3–5 overlapping clumps around the branch ends. Vary their sizes.
- Use a textured brush at a moderate size and dab points instead of dragging long lines. Dabbing produces a leafy edge that a smooth stroke can't.
- Let some branches show through the clumps, and leave gaps where the sky peeks through.
Silhouette matters more than detail at this stage. If the outline of your foliage looks like a smooth cloud, break it up with a few small clusters and stray leaves at the edges.
Step 5: Add Depth with Light and Shadow
Use three layers for the foliage, arranged around the base green:
- Dark layer below the base green. Paint shadow zones on the underside of each clump and near the trunk. Placing it under the mid-tone keeps the shadows tidy and easy to adjust.
- Mid-tone base layer. This is your main mass.
- Light layer above. Paint the highlights on the upper edges of each clump facing the light, using a lighter, slightly yellower green.
Keeping these as separate layers lets you adjust blend modes, opacity, and hue without repainting. Try setting the light layer to Overlay or Soft Light and compare it against Normal. You can also use the Adjustments menu (Hue, Saturation, Brightness, or Curves) on a single layer to shift mood for different times of day.
Add a cast shadow on the ground on its own layer, so you can move it or blur it independently.
Step 6: Detail and Finishing Touches
Detail should be restrained. Add it where the eye lands:
- A few individual leaves overlapping the edges of clumps.
- Darker accent greens deep inside the foliage, where light wouldn't reach.
- Small highlight marks on bark facing the light.
- A few roots, moss patches, or fallen leaves at the base.
- A soft glow or haze behind the tree to separate it from the background.
Then zoom out. If the tree still reads clearly at thumbnail size, the values are working. If it turns muddy, darken the shadow layer or brighten the highlights.
Common Mistakes to Avoid
- Uniform branch thickness. It makes the tree look like a wire structure.
- Symmetry. Unless you're going for a stylized look, avoid mirroring the left and right sides.
- Too many greens. Beyond three or four, the tree loses cohesion. Shift temperature (warmer in light, cooler in shadow) instead of adding new hues.
- Foliage with no structure. Leaves should hang from branches, so make sure clumps connect to the branch layout.
- Flattening too early. Merge layers only on a duplicate, so you keep an editable version.
Prepare Your Tree for Motion Work
If the tree is going into a motion graphics or VFX project, organize your Procreate file with animation in mind.
Layer structure worth setting up:
- Back branches
- Trunk
- Front branches
- Foliage clumps (one layer per major clump, if the tree will sway)
- Highlights and shadows
- Ground shadow
- Background or sky (on its own, or hidden)
Export as a layered PSD from Procreate's share menu, and bring it into After Effects as a composition with layers retained. From there you can:
- Use Puppet Pin on the trunk and main branches for a slow sway.
- Apply Wave Warp or Turbulent Displace to foliage layers with a small amount and a slow evolution to mimic wind.
- Offset each foliage clump's rotation or position by a few frames so they don't move in lockstep.
- Place several trees at different depths in 3D space for parallax, with background trees desaturated and slightly blurred.
For compositing with live footage, 3D passes, or cameras, a dedicated compositing pipeline such as After Effects or Nuke is more flexible.
Quick Recap
- Sketch a gestural trunk, not a perfect vertical.
- Draw tapering branches with overlap and gaps.
- Color the trunk, with shading clipped to the shape.
- Block foliage in masses by dabbing a textured brush.
- Use separate dark, mid, and light layers for depth.
- Add restrained detail, then check the silhouette at small size.
- Keep your layers organized so the tree can move later.
Treat the drawing as a structured asset rather than a flat picture, and it will be easy to refine, animate, or extend into other tools.