How to Draw Smooth Curved Lines in Procreate
StyleFrame Team7 min read
To draw smooth curved lines in Procreate, raise StreamLine and Stabilization in Brush Studio (Stroke Path and Stabilization tabs), then draw each curve in one fast, confident stroke from your shoulder or elbow rather than your wrist. For perfect ellipses and circles, draw the shape and hold the pencil at the end to trigger QuickShape. Free-form curves like an S-curve can be nudged afterward with Liquify's Push tool. If you need true Bezier control for motion work, finish the line in a vector tool.
Start with StreamLine
StreamLine is the setting that most directly removes wobble from curves. It smooths your stroke in real time, and the line trails slightly behind your pencil as if it were pulled along on a string.
To adjust it:
- Open the Brush Library and tap the brush you want to edit. Tapping a selected brush opens Brush Studio.
- Choose Stroke Path.
- Find StreamLine in the Stroke Properties on the right and raise the Amount.
At 0%, a curve picks up every tremor in your hand. At the maximum, curves come out very clean, which suits lettering, inking, and calligraphy, but the pull can feel unfamiliar at first. You may not always want it turned all the way up. Draw a few test arcs, an S-curve, and a spiral at each setting before committing to a value.
Duplicate the brush before editing it (swipe left on it in the library). That keeps your original intact, and you can always restore a brush's defaults from the About this Brush tab with Reset Brush.
Add Stabilization for longer, flowing curves
StreamLine handles small shakes. Stabilization smooths and straightens the overall stroke, which helps on long sweeping curves such as character silhouettes, logo shapes, or motion arcs.
There are two levels:
- Brush-level Stabilization: In Brush Studio, open the Stabilization tab and adjust both the Stabilization Amount and the StreamLine Amount for that one brush. This is the better choice most of the time, since a pencil sketching brush and an inking brush want different behavior.
- Global Stabilization: Tap the Actions (wrench) icon, go to Prefs > Pressure & Smoothing, and use the Stabilization slider (0–100%). This applies to every brush and overrides how they were built. A starting value around 10–15% is reasonable before you experiment with higher numbers.
If your pencil suddenly feels laggy or unresponsive, check global Stabilization first. It is easy to leave turned up after a smoothing session, and it affects every brush you pick up afterward.
Use QuickShape for perfect ellipses and circles
QuickShape snaps a rough stroke into a clean shape. Draw your shape, then hold the pencil down at the end of the stroke without lifting.
- Ovals and circles: Draw a rough loop and hold. It snaps to an ellipse. While still holding, touch the canvas with a finger to constrain it to a perfect circle.
- Straight lines: A wobbly line snaps straight when you hold. Add a finger touch and it jumps in angle increments, which gives you exact horizontals and verticals, handy for guides on a separate layer.
- Editing the shape: While you are still holding, or immediately after lifting when the edit option appears, you can resize, rotate, and switch between oval and circle. Once you tap away, the shape is committed and you would need Transform to change it, which may reduce quality in some versions of Procreate. Get it right the first time where possible.
QuickShape has limits for curves. It recognizes basic geometry, but it does not turn a hand-drawn S-curve or a swoosh into a clean path. Users have asked Procreate for a dedicated curve tool or Bezier-style point control, and as of the sources we reviewed, that is a gap. Plan for it by combining the methods in this article.
Build complex curves from simple pieces
Because QuickShape is reliable for circles and ellipses, you can use it as scaffolding:
- Draw a perfect circle or ellipse with QuickShape on its own layer.
- Use it as a guide to trace arcs on a new layer above, or erase the parts of the shape you don't need.
- For an S-curve, draw a straight line across the circle on a separate layer, then bend it with Liquify (next section).
This approach gives you geometric accuracy without redrawing the same arc ten times.
Bend lines after the fact with Liquify
When a curve is almost right but not quite, fix it instead of redrawing. A practical workaround is to put the line on its own layer, open Adjustments (the wand icon), choose Liquify, and select the Push mode. Then push the line gently into position.
Keep these points in mind:
- Isolate the line on its own layer so you only distort what you intend to.
- Use a modest brush size and a low pressure setting so the push is gradual and doesn't deform the line weight.
- Make small moves rather than stacking many passes.
Technique matters as much as settings
Software smoothing helps, but a few habits make it work better:
- Draw from the shoulder. Pivot from your elbow or shoulder for long curves. Wrist-only movement produces tight, wobbly arcs.
- Move at a steady, quick pace. Slow strokes show every tremor. A confident, continuous motion gives StreamLine less to correct.
- Rotate the canvas. Turn the canvas so the curve bends in the direction your hand moves most naturally, usually a pull toward your body.
- Start and end off the target. Begin the stroke slightly before the curve starts and let it run past the end, then trim with the eraser or a mask. This avoids hooks at line ends.
- Undo and redraw. Two-finger tap and try again. Replacing a stroke is faster than repairing it.
Know when to turn smoothing down
Smooth isn't always right. Heavy smoothing flattens energy in gesture drawing, rounds off corners you want sharp, and removes intentional texture in things like fur or frayed edges. Turn StreamLine and Stabilization down when you need spontaneity, hard angles, or precise technical detail. Keep a smooth inking brush and a loose sketching brush separate so you aren't resetting values constantly.
Take curves into a motion workflow
If your Procreate line work is headed to a motion project, the main question is whether you need it to stay raster. Procreate doesn't offer Bezier-style point control, so there are a few ways to handle that.
Keep it raster. For hand-drawn, boiling-line, or textured looks, export your artwork with transparency and animate it as footage or stills. Draw at a high canvas resolution so you can scale up in comp without softness.
Convert to vector. If you need clean, scalable curves, export a high-contrast version and run it through a tracing tool in a vector app. Smooth Procreate strokes with consistent weight trace much more cleanly than shaky ones, so the work you do with StreamLine pays off here.
Redraw with Bezier control. For a motion path or shape you need to animate precisely, use the pen tool in a vector or motion app to get handles, and animate the path directly. Use your Procreate drawing as a reference layer and trace over it. This is the right answer when exact curves matter more than a hand-drawn feel.
Quick troubleshooting
- Curves still look jittery: Raise StreamLine on the brush, then check that you're not drawing too slowly.
- Pencil feels delayed: Lower or turn off global Stabilization.
- Corners look rounded: Reduce Stabilization or use a different brush for hard-edged shapes.
- Shape got distorted after tapping away: QuickShape edits are lost once you tap away. Undo and redraw, or use Transform with care.
- Brush behaves strangely after tweaking: Use Reset Brush in the About this Brush tab, or duplicate brushes before editing next time.
Summary
For smooth curves in Procreate, tune StreamLine and Stabilization per brush, use QuickShape for circles and ellipses, fix near-misses with Liquify's Push, and rely on solid technique. When a project calls for exact, editable curves, finish in a Bezier-based vector tool.