How to Draw on Both Sides Procreate
StyleFrame Team7 min read
To draw on both sides in Procreate, turn on the Symmetry Guide: open Actions → Canvas, switch on Drawing Guide, tap Edit Drawing Guide, choose Symmetry, and tap Done. Anything you draw on one side of the guide line is mirrored in real time on the other side. The layer you're drawing on must have Drawing Assist enabled, which shows as "Assisted" under the layer name, or nothing will mirror.
Turn On the Symmetry Guide
The mirror tool lives inside Drawing Guides, not in the brush or transform menus. Here's the sequence:
- Tap the wrench (Actions) and open Canvas.
- Toggle Drawing Guide on. A grid appears over your canvas.
- Tap Edit Drawing Guide.
- Select Symmetry from the options along the bottom of the screen.
- Tap Done.
A vertical guide line now runs down the middle of the canvas. Draw a stroke on the left and it appears on the right as you work. The guide is an overlay on your artwork.
Make Sure Drawing Assist Is On for the Layer
This is where most "symmetry isn't working" problems start. Symmetry only affects layers with Drawing Assist enabled. The first layer you draw on after turning the guide on usually has it by default, and you'll see the word "Assisted" under its name in the Layers panel. A new layer you add afterward may not have it.
If you draw on a layer and nothing mirrors:
- Open the Layers panel and look for "Assisted" under the layer name.
- Tap the layer and choose Drawing Assist to enable it.
- Draw again. The mirrored strokes should appear immediately.
You can use this per-layer behavior on purpose. Keep a symmetrical base layer with Drawing Assist on, and put asymmetrical details (a scar, a stray hair, a lopsided highlight) on a separate layer with it off. That setup suits character and logo work, where perfect symmetry looks synthetic.
Choose the Right Symmetry Type
Procreate offers four symmetry layouts. To switch between them, go back to Edit Drawing Guide and open the Symmetry Options.
Vertical symmetry
A guide runs vertically down the middle. Drawing on the left reproduces on the right, and vice versa. Use it for faces, creature heads, vases, glassware, front-facing vehicles, and icons.
Horizontal symmetry
A guide runs horizontally across the middle. The top half mirrors to the bottom half. It's useful for reflections, water surfaces, and anything viewed as a top/bottom pair. Note that drawing a heart or a face upright is awkward in this mode, because your strokes mirror vertically instead of side to side.
Quadrant symmetry
Both a horizontal and a vertical guide divide the canvas into four quadrants. A mark in one quadrant appears in the other three. It's the practical choice for tileable patterns, frames, ornamental corners, and title-card borders.
Radial symmetry
Radial divides the canvas into eight segments using horizontal, vertical, and diagonal guides. Draw in one segment and the other seven fill in. This is the mode for mandalas, snowflakes, kaleidoscope textures, and logo burst shapes. You don't have to stay inside a single segment. Strokes drawn anywhere are repeated around the center.
Mirrored vs. Rotational Symmetry
By default, Procreate uses Mirror Symmetry, which reflects your strokes across the guide as if a mirror sat on the line. If you switch on the Rotational Symmetry toggle in the options, the stroke is reflected and rotated, so the copy is flipped both horizontally and vertically at once.
Rotational symmetry gives you swirling, spiral-like results. It's fun for abstract motifs, but it's a poor fit for seamless connecting patterns, because the repeats don't line up the way mirrored copies do. For tile work, stay with mirror mode in Vertical, Horizontal, or Quadrant layouts.
Reposition and Rotate the Guide
The guide doesn't have to sit dead center. When you edit the guide, two nodes appear:
- Blue node (positional): moves the whole guide across the canvas.
- Green node (rotational): rotates the guide lines so you can mirror along an angle.
To snap back to the default layout, tap one of the nodes and tap Reset.
Offset and angled guides are handy for three-quarter views, dynamic logo shapes, and compositions where the axis of symmetry shouldn't be the exact center of the frame. Keep Drawing Assist on when working at an angle so your strokes follow the guide direction.
Adjust Guide Appearance So You Can Actually See It
On the Drawing Guides screen you can change three things about the lines:
- Color: use the hue bar at the top. Don't set it to white on a white canvas, or the guide seems to vanish. Pick a color that contrasts with your artwork.
- Opacity: from invisible to fully opaque.
- Thickness: from invisible to noticeable.
Tap Done to commit your changes or Cancel to leave without changing anything.
Color, Fill, and Edit Symmetrical Artwork
A few habits keep symmetrical work clean:
- Use Alpha Lock for color. Draw your line art or shapes on one layer, turn on Alpha Lock, and paint over them. The mirrored result carries through, as long as the layer is assisted.
- Fill on assisted layers. Fill behavior follows the same layer logic, so keep the layer assisted if you want mirrored results.
- Turn the guide off when you're done. Go back to the layer or Edit Drawing Guide and disable Drawing Assist to paint freely without the mirror.
- Separate symmetrical and asymmetrical elements. Keeping them on different layers makes later changes much easier.
Why Symmetry Matters in a Motion Workflow
For motion designers, animators, and VFX artists, symmetrical drawing in Procreate is rarely the end product. It's a fast way to build assets that go into an After Effects, Cinema 4D, Blender, or Nuke pipeline:
- Character and creature front views. Mirror-drawn heads and bodies make reliable front references for rigging or modeling.
- Logo and sting elements. Radial and quadrant modes quickly generate ornate marks, badges, and burst shapes you can animate in After Effects.
- Pattern and texture sources. Tiles drawn with quadrant symmetry can become backgrounds or mattes.
- Mandala and kaleidoscope loops. Radial artwork suits rotational animation in a compositor.
- Style frames. A fast symmetrical sketch communicates a layout or silhouette before you commit to full production.
Export with layers separated where you can, such as line art, color, and highlights on distinct layers. That keeps the artwork flexible once it lands in your compositing or 3D tool.
Troubleshooting Common Symmetry Problems
Nothing mirrors when I draw. Check that Drawing Guide is on and that your current layer says "Assisted." If it doesn't, tap the layer and enable Drawing Assist.
The guide line disappeared. The line color may be set to match your canvas, or the opacity or thickness may be at minimum. Reopen Edit Drawing Guide and adjust them.
The mirror is on the wrong axis. Open Options under Symmetry and switch between Vertical, Horizontal, Quadrant, and Radial.
The reflection looks rotated instead of mirrored. Rotational Symmetry is switched on. Turn off the toggle to return to mirror behavior.
The guide isn't centered. Drag the blue node to move it, or tap a node and choose Reset to restore the default.
New layers don't mirror. Each new layer may need Drawing Assist enabled individually.
Quick Reference
Once the guide is configured and assisted on the right layers, drawing on both sides in Procreate is a matter of drawing once. The main details to remember are that Drawing Assist is set per layer, that mirror mode suits patterns while rotational mode suits swirls, and that the guide can be moved and rotated to fit your composition.