How to Draw Hair Im Procreate
StyleFrame Team7 min read
To draw hair in Procreate, sketch the whole head first, mark where the hair parts and which way it flows, then block the hair in as a few large clumps rather than individual strands. Fill the shape with a dark base color, build mid-tones and highlights on separate clipped layers with a textured hair brush, and finish with a handful of thin flyaway strands along the edges. Hair reads as believable when the big shapes, light direction, and flow are right, so strand detail should come last.
What You Need Before You Start
You don't need much:
- Procreate on an iPad, ideally with an Apple Pencil for pressure sensitivity
- A reference photo or a character design to work from
- A small palette of a few colors for one hair color, from a deep base to a light highlight
- One textured brush for clumps and a thin brush for strands
Procreate's default brushes are enough. A 6B pencil works for sketching, and the round brush or brush pen handles color and rendering. Custom hair brush packs speed things up but don't replace the fundamentals below.
Understand Hair Types and Flow First
Hair behaves differently depending on its type, and that affects the shapes you draw.
- Straight hair is glossy and lies close to the head. Expect long, smooth shapes with sharp, narrow highlights.
- Wavy hair follows an S-shaped rhythm. Highlights break up along the curves.
- Curly hair forms spirals with real volume. The hair sits away from the scalp, so shadows are deeper between the curls.
- Coily hair has tight, dense curls. Treat the overall silhouette as one mass and describe the texture within it, rather than drawing every coil.
Whatever the type, hair grows from a starting point, usually the part, a crown swirl, or a hairline. Everything flows outward from there. Pick that point or line before you draw anything else, because it dictates the direction of every stroke you make later.
Step-by-Step: Drawing Hair in Procreate
1. Draw the whole head first
Sketch the full skull shape, including the part hidden by hair. This stops you from making the hair too small or the head too large. Hair has thickness, so the outline should sit visibly off the scalp, especially at the crown and sides.
2. Mark the part and the flow
On a new sketch layer, place the starting point or part line. Then draw a few long guide lines flowing away from it. Keep them loose. These lines are for you and will be hidden later.
3. Break the hair into clumps
This is the step that separates convincing hair from a scribble. Group the flow lines into larger sections. Some artists think of them as banana or ribbon shapes. Each clump has a top edge, a body, and a tapered end. More clumps means more detail, so choose a number that matches your style.
4. Fill a dark base on its own layer
Create a new layer and fill the full hair silhouette with your darkest color. Clean up the edges. Starting dark means you won't need to paint heavy shadows later, because the gaps between strands will already read as depth.
5. Add mid-tones with a clipping mask
Add a layer above the base and set it as a clipping mask. Now any color you paint stays inside the hair shape, so you can work freely without damaging the silhouette.
With a textured or strand-style brush, paint thicker strokes in a mid-tone, following the flow lines from your starting point. Keep the strokes grouped into the clumps you planned. If the tone looks too dark or too saturated, turn on Alpha Lock for that layer and adjust the color with a soft airbrush.
6. Build highlights in layers
Add a new layer for each lighter value. As you go lighter, switch to thinner strokes and apply them less often. Place highlights where light would hit the hair's highest curves, not evenly across the whole head. Hair near the roots and in recesses is usually darker, so keep those areas dim.
For curly hair, add a highlight to the top of each curl and leave the underside in shadow. For straight hair, a single band of light that follows the curve of the head sells the gloss.
7. Blend the start and end points
Hair strands look harsh when every stroke begins and ends with a hard edge. Use a soft airbrush or a blending brush set to a low opacity and gently soften where strokes begin and taper. Don't blend the whole layer. If you smudge it all, you lose the strand texture you just built.
8. Add edge detail and flyaways
On a layer beneath your main hair layers, add a few fine strands around the hairline and outer edge. Put some in front of the face or shoulders on a top layer. Use thin brushes, vary the length, and let some curve against the main flow. Restraint matters here, because too many flyaways look like noise.
9. Adjust with opacity and blend modes
Finally, use layer opacity and blend modes to fine-tune contrast. Because each tone lives on its own layer, you can change the whole feel of the hair, such as a warmer rim light or a deeper shadow, without repainting.
Brush and Layer Tips That Save Time
- Keep one layer per tone. It's slower to set up and much faster to revise.
- Use pressure to taper. A stroke that starts thin, thickens, and ends thin looks like hair. A uniform line looks like wire.
- Vary stroke length. Mix long sweeping strokes with short ones inside each clump.
- Zoom out often. Hair should read from a distance. If the clumps don't hold at thumbnail size, more strands won't help.
- Work from reference. Study how illustrators and animation studios group hair into a few readable shapes. Simplified, stylized hair still follows a starting point and clear clumps.
Common Mistakes
- Drawing individual hairs first. Start with volume and sections, and add strands last.
- Ignoring the skull. Hair that doesn't sit on a head shape looks like a wig floating in space.
- Uniform highlights. Even lighting flattens the form. Let the light fall on one side.
- Over-blending. Smoothing everything removes texture.
- Too many tiny strokes at the same value. If values are too close, the hair turns muddy. Keep a clear gap between base, mid, and highlight.
Using Your Procreate Hair Art in a Motion Pipeline
For motion designers, animators, and compositors, hair drawn in Procreate often becomes a design asset. It might be a character style frame, a texture reference, or a keyframe for something that needs to move. You can bring the base, mid-tone, highlight, and flyaway layers into a compositing tool such as After Effects and separate them for parallax, simple secondary motion, or color adjustments. That layered structure is a major reason to keep each tone on its own layer from the start.
Animating hair frame by frame is still labor-intensive, though, and that's where an AI video tool can help if it gives you real control. is one option to look at for that kind of artist-led workflow rather than one-click generation.
Your compositing workflow can stay intact: Procreate for design, Styleframe for generating and refining motion from your art, and your usual compositor for final assembly. As with any generative tool, test it on your specific hairstyle first, because very fine strand detail and complex curls are where you'll want to review results closely.
Quick Checklist
- Draw the full head and place the part or starting point.
- Sketch flow lines, then group them into clumps.
- Fill a dark base on its own layer.
- Add mid-tones in a clipped layer, following the flow.
- Layer highlights from medium to light, thinner each time.
- Blend start and end points, but not the whole layer.
- Add flyaways and edge strands sparingly.
- Tune contrast with opacity and blend modes.
Once these steps feel natural, you can adapt them to any hair type or style, and keep the layered file organized so it moves cleanly into your animation or compositing pipeline.