How to Draw Eyes Procreate
StyleFrame Team7 min read
To draw an eye in Procreate, start with a light sketch on its own layer: an almond shape for the lids, a circle for the iris partly covered by the upper lid, then the crease, lash line, and tear duct. Put base colors, shading, lashes, and highlights on separate layers underneath or above that sketch so every pass stays editable. Work from a reference, keep the whites of the eye slightly gray rather than pure white, and add the glint last. The same layered file can later become keyframes for animation.
Set up the canvas and reference
Create a canvas large enough to zoom into without losing detail. Something like 3000 × 2000 px or larger works well for a single eye study. If the drawing will end up in a video timeline, match the aspect ratio of your comp instead of defaulting to a portrait canvas.
Bring in a reference photo and keep it visible while you work. You can import it directly onto the canvas and move it aside, or import it as a reference in Procreate. A small mood board of several eyes is better than one photo, because it trains you to see the shared structure rather than copying one set of details.
Choose a sketching brush with a bit of tooth (a pencil or chalk-style brush is fine) and a soft airbrush for blending. You do not need custom brushes. The built-in set is more than enough.
Step 1: Block in the basic structure
Eyes look wrong when the structure is off, not when the detail is missing. Start with these shapes on a new layer:
- The eyeball direction. Draw a loose circle or oval to mark where the eye is looking and how the head is tilted.
- The iris. Add a smaller circle inside it. In most eyes the upper lid covers a slice of the iris, and the lower lid just touches or sits slightly below it. A fully exposed iris reads as startled.
- The lids. Wrap an almond shape around the eyeball. The inner corner is usually more pointed and the outer corner sits a little higher or lower depending on the face.
- Crease and lash line. Draw the upper-lid crease above the lash line, and give the lower lid a thin second line to show its thickness.
Keep these lines light. Lower the opacity of this layer, then draw a cleaner pass on a new layer above it. This two-pass habit saves time because you correct proportion in the rough stage and only commit once it looks right.
Step 2: Refine the line drawing
On the clean layer, add the small landmarks that make an eye feel specific:
- The tear duct (caruncle) in the inner corner
- The pupil inside the iris
- A highlight shape, placed deliberately rather than sprinkled in
- The fold of the eyelid
- Any wrinkles or bags that match your reference
Resist the urge to draw every lash yet. Mark only the general direction and clusters. Lashes get their own layer later.
Step 3: Lay down flat base colors
Create new layers beneath the sketch. Fill the skin tone first with a soft airbrush, lightly and without worrying about edges. Then add a separate layer for the eyeball itself.
Do not use pure white for the sclera. In reality it is a soft gray or warm off-white, darker near the lids where shadow falls and lighter toward the center. A stark white looks like a sticker. Sampling color from your reference is the quickest way to get this right. In Procreate, hold your finger on the canvas to open the eyedropper.
Keep each major element on its own layer: skin, sclera, iris, pupil. If you make a mistake, you only fix one layer.
Step 4: Build the iris
The iris is where the eye gets its character. Work in stages:
- Fill the iris with a mid-tone base color.
- Create a clipping mask layer above it so anything you paint stays inside the iris shape.
- Darken the outer rim (the limbal ring) with a soft brush.
- Use thin strokes radiating outward from the pupil to suggest fibers. Alternate lighter and darker tones for texture.
- Add a darker pupil and soften its edge slightly.
The upper lid casts a shadow across the top of the iris, so darken that region on a separate layer set to Multiply. This one detail does more for realism than any amount of extra texture.
Step 5: Shade the lids and the surrounding skin
Soft shadows give the eye volume. On a new Multiply layer:
- Darken the crease and the area directly under the upper lid.
- Add a faint shadow in the inner corner near the tear duct.
- Show the thickness of the lower lid with a subtle highlight along its edge and a shadow beneath it.
- Blend with a soft airbrush or the Smudge tool at low pressure.
Move slowly here. Several light passes look more natural than one heavy one. If a shadow is too strong, drop the layer opacity instead of erasing.
Step 6: Draw the lashes and brows
Lashes are not straight sticks. They curve, they overlap, they bunch into clusters, and they change direction between the inner and outer corners. Upper lashes sweep up and out, while lower lashes are shorter, sparser, and point down and out. Drawing them too short is a common mistake that makes an eye look flat.
Put lashes on their own layer so you can adjust, erase, or reposition them without touching the skin. Use a tapered brush and flick each stroke from the root outward in one confident motion. A lash-style stamp brush is a legitimate shortcut if the goal is speed: stamp it on a new layer, then resize and flip it. Just make sure the lashes follow the eye's curve.
Add brow hairs the same way, following the direction of growth: angled upward near the inner end, then arching and following the brow's shape.
Step 7: Add highlights last
Highlights make an eye feel wet and alive. Add a crisp specular reflection on the iris and pupil, a smaller secondary glint if your reference has one, and a thin moist line along the lower lid and tear duct. Use a hard-edged white brush on a new layer, and keep it small. Too many highlights make the eye look glassy or fake.
Finally, zoom out and compare against the reference. Check values first (is the darkest dark dark enough?), then edges, then color. Lids can almost always go darker and lashes can usually use more shadow beneath them.
Stylized eyes: simplify on purpose
If you want a cartoon or illustrated look, the same structure applies. You just decide which elements to keep. A useful exercise is to fill a page with 50 eyes, each using a different mix of shape, size, and detail. Some can be just an oval and a dot, others can include lids, lashes, and reflections. That range teaches you which elements carry the expression, and it lets you develop a consistent style across characters.
Turn your eye drawing into motion
For animators and motion designers, a static eye is often the start of a shot: a blink, a glance, a pupil dilation, or a stylized close-up. Procreate's layered structure makes this practical if you prepare the file well.
Prep the file for animation:
- Keep lids, iris, pupil, highlights, and lashes on separate layers.
- Name your layers. It feels tedious while drawing and saves a lot of time in a timeline.
- Export your layers or flattened frames in a format your animation software accepts.
- Draw key poses: eye open, half-closed, closed, and any look direction you need.
Animate in your usual tools. In your animation software, you can animate the lid layers and move the iris and highlight independently.
Common mistakes to avoid
- Eyes that look flat: usually missing shadow from the upper lid on the eyeball and iris.
- Pure white sclera: use soft gray or warm tones instead.
- Straight, uniform lashes: vary length, curve, and clustering.
- Misplaced iris: check how much the upper lid covers it.
- Too many highlights: one strong glint with a subtle secondary is usually enough.
- Everything on one layer: you lose the ability to adjust, and animation prep becomes painful.
Practice routine
Observation beats memorizing steps. Draw a handful of eyes from different references each day, first as quick structural sketches, then as fuller renders. Compare your drawing to the reference side by side at the end, note the biggest differences, and fix those on the next attempt. After a week or two, the structure becomes automatic and you can spend your effort on style, expression, and, if you animate, on how the eye moves.