How to Draw Dreads on Procreate
StyleFrame Team6 min read
To draw dreads in Procreate, start with a loose silhouette of the whole hairstyle on its own layer. Then draw each dreadlock as a slightly irregular, tapered tube with a small curl at the end, and finish with a heavier outer line, lighter interior texture marks, and shading on separate layers. Don't draw every lock perfectly straight or identical, because the variation in thickness, angle, and overlap is what reads as dreadlocks. If the character will be animated or composited later, keep the locks on separate layers so you can move, recolor, and export them cleanly.
What You Need Before You Start
You don't need a custom brush pack. A basic setup is enough:
- A sketch brush with some pencil texture for the construction layers.
- An inking brush with pressure sensitivity, such as Studio Pen, for the final line.
- A soft or textured brush for shading, such as Soft Airbrush.
Most dreads look better with asymmetry, so you may want to avoid symmetry tools.
Step 1: Block Out the Head and Hair Silhouette
Create a new layer and sketch the head shape with a center line and a rough hairline. Dreads sit on the head in clumps, so you need to know where the scalp ends and the hair mass begins.
On a second layer, draw the overall volume of the hair as a loose, cloud-like outline. Decide at this stage:
- Whether the hair is pulled up, half-up, or hanging down.
- How long it is. Shoulder length, waist length, and very long dreads all need different amounts of overlap.
- The parting or hairline pattern, since locks usually radiate from a part or from sections around the crown.
Lower this silhouette layer's opacity to around 30–40% so you can draw over it. A rough shape is fine. You're only setting the proportions that the individual locks will fill.
Step 2: Draw the Individual Locks
Create a new layer above the silhouette. Start at the hairline and work outward, drawing one lock at a time.
Shape each lock like a tapered tube
A dreadlock is roughly cylindrical, but it isn't a perfect straight tube. Give each one:
- A slight wobble or angle in the outline, not a ruler-straight edge.
- Uneven width, a bit thicker in the middle or near the root and tapering toward the tip.
- A small curl, frayed tip, or blunt end so the ends don't all look identical.
If you want to keep the hand-drawn feel, don't over-smooth your lines. A little wobble keeps them from looking vector-clean.
Build from the front to the back
Draw the front locks first and let them overlap the ones behind. Then move to the sides and the back. Overlap creates depth faster than shading does. Vary the angle of each lock. Some fall straight, some cross over others, and some curve outward from the head.
Keep sections organized
Put the locks that fall in front of the face on one layer, the sides on another, and the back on a third. This takes a few extra seconds, but it makes the later steps, especially shading and animation prep, much easier.
Step 3: Add Line Work and Texture
Drop the opacity of your sketch layers and create a new layer for inking. Use a two-weight approach:
- Outline each lock with a heavier line. Press a little harder or use a slightly larger brush size.
- Add lighter interior marks. Short squiggles, small spiral lines, and wrap-like curves suggest the twisted, matted texture inside each lock.
Don't fill every inch of a lock with texture. A few marks near the root, the middle, and the tip are enough, and leaving gaps keeps the drawing readable. Too many lines make the hair look muddy, especially at smaller sizes.
Finish with the ends. A small curl or a slightly irregular cut is more convincing than a clean, rounded cap.
Step 4: Color and Shade
Lay in the base color
Create a layer below your line art and fill the hair with a flat base color. Using a fill tool is fast, but check for gaps in the line work first. If a color leaks, close the gap on your ink layer.
Keep shading inside the hair shape by locking the base color layer or by masking a new layer above it to the hair shape.
Shade in layers
Work in a simple sequence:
- Core shadow: On a separate layer above the base color, paint a darker tone on the side away from the light, and underneath where one lock overlaps another.
- Cast shadow from the head: Add shadow near the scalp and where locks fall behind other locks.
- Highlights: On another layer, paint lighter tones along the edge facing the light. Keep them in short strips that follow the form of each lock, not a single large gloss.
If the character has colored or dyed dreads, shift the hue slightly in the shadows instead of just darkening the base color. Cool shadows on warm hair, or the reverse, feel more natural than gray-black shading.
Step 5: Fix Common Problems
The dreads look like sausages or rope. The locks are too uniform. Vary the width, add small kinks, and break the outline with slight irregularities.
The hair looks flat. Add more overlap and shadow between locks, especially near the scalp and where a front lock crosses a back one.
The hairline looks pasted on. Let a few shorter locks sit near the forehead and temples, and soften the transition with a few lighter marks near the root.
The texture is noisy. Reduce the number of interior lines and keep them lighter than the outline.
The shapes feel too symmetrical. Flip the canvas horizontally often. A mirrored view makes lopsided proportions obvious right away.
Preparing Your Dreads Drawing for Animation and Compositing
If the drawing is going into a motion project, your layer structure matters as much as the drawing itself.
- Group the locks by region (front, sides, back, ends) and name the groups. Export a layered file that your editing software can open with the layers intact.
- Keep line art, flat color, and shading on separate layers. This lets you recolor or adjust the shading separately.
- Paint a bit beyond the final edges of hair that will be moved, such as where a lock overlaps the neck or shoulder, so you don't expose empty gaps when you separate layers.
- Draw a few alternate poses of the ends if the hair will swing. Even two or three hand-drawn positions give you stronger material than a single static pose.
For simple movement, you can rig the groups in your animation software. For frame-by-frame work, you can test short loops and bring them into your editor as image sequences.
Quick Checklist
- Block out the head and hair silhouette on separate layers.
- Draw each lock as a tapered, slightly irregular tube with a curled or uneven end.
- Overlap locks, working from front to back.
- Use a heavier outline and lighter interior texture marks.
- Shade on separate layers with a consistent light direction.
- Keep groups and layers organized for export to your animation or editing software.
Once the basic method feels natural, vary lock thickness, length, and style to design different characters. The same construction works for thin, thick, short, long, or stylized dreads.