How to Draw Dotted Line in Procreate
StyleFrame Team7 min read
To draw a dotted line in Procreate, duplicate the built-in Monoline brush, open Brush Studio, and raise the Spacing slider under Stroke Path until the stamps separate into individual dots. Set the taper sizes to none so each dot stays uniform, then save the brush and draw with it like any other. For straight dotted lines, draw a stroke and hold at the end so QuickShape snaps it straight.
How to make a dotted line brush in Procreate
A dotted line in Procreate comes from a custom brush. A dotted line is a round brush whose stamps are spread apart.
- Duplicate a base brush. Open the Brush Library, select Monoline (in the Calligraphy set), swipe left on it, and tap Duplicate. Always work on the copy so the original stays intact.
- Open Brush Studio. Tap the copy to open its settings.
- Increase spacing. Go to Stroke Path and drag Spacing to the right. Somewhere around 60–70% tends to give clearly separated dots, but judge it by the preview on the drawing pad. Higher values push the dots further apart.
- Remove tapering. Under Taper, set all the taper sizes to none. Otherwise the dots at the start of each stroke come out smaller than the rest.
- Tune stabilization. Open Stabilization and adjust Streamline, Stabilization, and Motion Filtering to taste. Higher streamlining gives smoother curves, which matters because stamp placement along a wobbly path looks uneven.
- Name and save. Tap About this brush, rename it (for example "Dots – Even"), and tap Done.
Draw a test stroke on a new layer at a few sizes to see how the brush looks at each one.
Drawing a straight dotted line
Freehand dotted lines look hand-drawn, which is sometimes exactly what you want. For technical diagrams, motion-path callouts, or UI-style overlays, you want something clean.
- Draw a line with your dotted brush, then keep your Apple Pencil on the screen at the end of the stroke. Procreate's QuickShape snaps the stroke into a straight line.
- While still holding, you can adjust the length and angle of the line.
How to make a dashed line brush
A dash is a dot with a custom shape, so the process adds one step: telling Procreate to stamp an elongated shape instead of a circle.
- Create a square canvas (1080 × 1080 px is enough).
- With a monoline brush at maximum size, draw one short, straight line. Hold at the end of the stroke to straighten it with QuickShape. If you want precision, center it on the canvas using Snapping in the Transform tool.
- Copy the layer (swipe down with three fingers to open the copy menu, or use the layer menu).
- Duplicate your dotted brush and open Brush Studio.
- Choose Shape, tap Edit, then Import, then Paste. Procreate loads your line as the stamp. If the shape appears inverted (dark line on a white field when you need the opposite), two-finger tap in the shape editor to invert it. Tap Done.
- Set Rotation to Follow Stroke so the dashes align with the direction you draw.
- Adjust Spacing until the gaps look right.
If the dashes behave strangely when you draw, check the Properties section and turn off Orient to Screen. That setting can make stamps ignore the stroke direction. Also experiment with the length of the line you pasted: a shorter line yields shorter dashes, a longer one gives longer dashes.
Variations worth building
Once you have the basic brush, small changes produce very different results.
- Hand-drawn irregularity. Under Dynamics, add a little Size jitter so dots vary. A moderate value such as 60% creates a clearly organic look; keep it low for something subtle.
- Consistent opacity. If dots fade in and out with pressure, open Apple Pencil settings and drag the opacity pressure slider fully to the left so every dot has the same density.
- Color shifts. In Color Dynamics, Stamp Color Jitter with a small Hue value (around 5–10%) makes each dot drift slightly in color. Pushing it much higher turns the line into a rainbow.
- Pressure-sensitive size. If you want dots that swell with pressure, leave size pressure active; for uniform technical lines, turn it off.
- Separate brushes for separate jobs. Keep a tight-dot brush for fine outlines, a wide-gap one for borders and lettering, and a dash brush for path indicators. Putting them in their own brush set keeps them quick to reach.
Troubleshooting dotted lines you didn't ask for
Sometimes the problem is the opposite: your normal brushes suddenly draw dots.
- Streamline set to None. Users have reported that with Streamline at zero, strokes break into dots, and raising it to any value restored normal lines. Check Stabilization on the affected brush first.
- Pencil connection quirks. After one past Procreate update, users saw fast strokes break into dots or angular segments. Procreate staff acknowledged it and released a patch. Before the patch, one workaround was tapping the Pogo button under Actions → Connect third party stylus. If you see this behavior now, update Procreate and iPadOS, and test your pencil in another app to rule out hardware.
- Reset the brush. If a single brush misbehaves after you've edited it, duplicate a fresh copy of the original instead of continuing to patch settings.
- QuickShape lines look dotted. Some users have reported QuickShape output appearing dotted after updates. Check that your brush isn't a spaced-out custom one, and contact Procreate support if it persists across brushes.
Getting a Procreate dotted line into a motion workflow
If your destination is After Effects, Premiere Pro, or a 3D package, decide early whether the dotted line should be raster art or something you build natively.
Export as raster art. Hide the background layer and export in a format that preserves transparency, keeping layers if you need them. Work at a large canvas size, because dotted lines have hard edges that will soften if you scale them up in your comp. Import into After Effects and treat it as a texture, a hand-drawn overlay, or a stamp for a map or storyboard.
Build it natively when it needs to animate precisely. A dotted line that travels along a path, draws on, or scales with a comp is usually easier to build with native vector shape tools in your motion software. That keeps it resolution-independent and editable. Procreate is better when you want imperfection, texture, or the specific character of your own hand.
Combine the two. A common approach is drawing a few hand-made dotted strokes in Procreate, importing them as frames or stills, and layering them over clean vector-based motion to add a handmade feel.
Where Styleframe fits
Once a dotted-line drawing exists in Procreate, it can serve as a style reference rather than only a finished asset. Styleframe is an AI video and motion tool, and a Procreate sketch with your dotted linework can act as a reference for the look you want.
Practically, that means you can draw the look once in Procreate and carry it into moving imagery without redrawing every frame.
Use it where hand-drawn character matters across many frames. For a simple animated dotted path, native vector shape tools in your motion software are still the faster and cleaner route.
Quick reference
Spend a few minutes making a small dedicated brush set, and you'll have dotted and dashed lines ready for any illustration, storyboard, or motion project.