How to Draw Curves in Procreate
StyleFrame Team7 min read
Procreate has no Bézier pen tool, so you draw curves in one of two ways. You can draw a stroke and hold the pencil at the end so QuickShape snaps it into a clean arc, then drag the nodes with Edit Shape. Or you can draw freehand with StreamLine and stabilization turned up, then correct the result with Liquify. Because Procreate is raster-based, anything you want as an editable vector path in After Effects has to be traced afterward.
Why Curves Work Differently in Procreate
If you're used to the Pen tool in After Effects, Illustrator, or Photoshop, Procreate will feel imprecise at first. There are no anchor points with handles on a persistent path. A stroke is pixels, and the only "live" curve you get is the temporary one QuickShape creates before you tap away.
That matters for motion work. Procreate is a good place to sketch a swoosh, a character silhouette, a logo gesture, or an arc for a transition. It isn't where you build a path you'll animate with trim paths or path keyframes. Plan to draw the shape there and rebuild or trace it downstream.
Users have been asking for a Manga Studio-style curve tool, or Bézier control over polyline points. Until something like that ships, the methods below are the practical options.
Method 1: Draw and Hold, Then Edit Shape
This is the fastest route to a clean curve.
- Pick the brush you want for the final line. A monoline or a tapered inking brush shows the result most clearly.
- Draw a rough curve in one stroke.
- Keep the pencil on the screen at the end of the stroke and wait for it to snap.
- Tap Edit Shape.
- Drag the nodes to reposition the arc, lengthen it, or flatten it.
The same hold-to-snap behavior gives you perfect circles and ovals, and straight lines and rectangles. While the shape is still held, touching a second finger to the screen constrains it. A hold on an oval can turn it into a circle, and a hold on a line can lock it to set angle increments.
The catch: once you tap away, the shape is committed and Edit Shape disappears. Your only option after that is Transform, which resamples pixels. Get the arc right before you tap away. If you need a different curve, undo and redraw rather than stretching a committed stroke.
Building S-curves and compound shapes
QuickShape handles one arc at a time and doesn't detect S-curves or complex splines. To build an S-curve, draw two arcs on the same layer or on separate layers, each with its own hold-and-edit pass, and make sure the end of the first meets the start of the second. Putting each arc on its own layer lets you nudge them independently and avoids a visible kink at the join.
Method 2: Freehand Curves With StreamLine and Stabilization
When you want a hand-drawn feel rather than a geometric arc, let Procreate smooth your stroke while you draw.
- Open the brush in Brush Studio and go to Stroke Path.
- Raise StreamLine. At the maximum, wobbles are largely filtered out. At zero, the line follows every tremor of your hand.
- Stabilization can also help. The best mix depends on the brush.
Higher StreamLine suits inking, calligraphy, and long sweeping curves. The trade-off is lag and some loss of intent. Very high smoothing can round off corners or pull the line away from the path you meant to follow. Duplicate your working brush before editing it so the default stays intact, and keep a "smooth" version for long curves and a "loose" version for sketching.
Drawing technique matters as much as settings. Move from the shoulder or elbow rather than the wrist, draw the curve in one confident motion, and rotate the canvas so the arc sits in your natural pencil sweep. Redrawing three times is usually faster than fixing one bad stroke.
Method 3: Use Drawing Guides to Constrain Curves
Drawing guides don't create curves directly, but they make curves consistent.
- Perspective guide: place a vanishing point and the lines you draw converge on it, which helps with curves that wrap around a receding surface.
- 2D grid: reduce the grid size and use it for spacing and alignment when you're laying out repeating curved elements.
For lettering that follows an arc, one approach is to draw and snap your curve, lower its opacity, and duplicate it upward to create a baseline and an x-height line. Then paint vertical spacing guides on a separate layer, mark the center of the arc, and letter on a new layer on top. Group the guides so you can hide them all at once. It's manual, but it works because Procreate doesn't offer type on a path.
Method 4: Fix Curves After Drawing With Liquify
If a line is nearly right, bend it instead of redrawing.
Liquify Push
Put the curve on its own layer, open Adjustments > Liquify, and choose Push. Drag the line into place. This is a workable stand-in for a curve tool. For example, you can draw a circle, add a straight line across it on a new layer, then push the line into an S-curve.
Keep the Liquify size and pressure low. A heavy push smears a clean stroke, and a very thin line can break up when pushed too far.
Keep curves on separate layers
Whatever method you pick, keep each major curve on its own layer. That keeps Liquify edits non-destructive to everything else, and it makes the file easier to hand off later.
Getting Procreate Curves Into After Effects
Once the curve exists, you have a few ways to bring it into a motion pipeline.
As raster art. Export the artwork as an image file and import it into After Effects. Use this for textures, hand-drawn overlays, and anything where the line quality is the point. Export at a size larger than your comp so you can scale without softness.
As a traced vector. If you need an animatable path, trace it. Use a tracing tool in a vector or compositing app to convert a high-contrast line drawing into paths. Clean, high-contrast, single-color line art traces best. Textured brushes produce messy paths with many points.
As a reference for rebuilding. For precision work such as a motion path, logo build, or trim-path animation, import the sketch, lock it, and draw the path with the Pen tool on top. You get exact handles and a path you can edit forever, using Procreate for the gesture and After Effects for the construction.
Draw with a plain, opaque, hard-edged brush when you intend to trace. Tapered or textured strokes add noise that you'll spend time cleaning up.
Common Problems and Quick Fixes
- Curve looks lumpy: raise StreamLine, draw faster in one motion, or use hold-to-snap and Edit Shape.
- Arc won't edit: you tapped away. Undo and redraw, and adjust nodes before tapping away.
- Line weight changes when bending: redraw the stroke with a monoline brush.
- Traced path has too many points: simplify the path in your vector tool, or retrace from a cleaner, higher-contrast export.
- Edges soften after scaling: work at a larger canvas size and avoid repeated Transform passes.
A Practical Workflow
- Sketch loosely with a stabilized brush.
- Redraw key curves with hold-to-snap and Edit Shape on separate layers.
- Use Liquify Push for small corrections.
- Export your artwork as image files.
- Trace or rebuild paths in a vector or compositing app where you need real vectors.
Procreate's curve tools are limited, but they're enough for gesture, shape design, and reference art if you treat the app as a sketching surface and finish the precise work in your vector and compositing tools.