How to Draw Curls on Procreate
StyleFrame Team5 min read
To draw curls in Procreate, block in the overall hair shape first, then build curls on separate layers using short, overlapping S-shaped or spiral strokes that follow the direction of hair flow. Work from dark to light, keep each tonal pass on its own layer, and use Liquify and clipping masks to fix the silhouette without redrawing. Drawing the curls as grouped ribbons of hair, not as individual strands, is what makes them read as believable.
Start with the silhouette, not the squiggles
The most common mistake is jumping straight into spirals. Loose squiggles across an empty canvas leave gaps, and you end up spending most of your time patching them. Start with the mass.
- Create a layer named "Hair base."
- Using a solid-edged brush (a calligraphy or inking brush works well), outline the outer shape of the hair. Think about the hair as one volume sitting on the head, not a collection of curls.
- Fill the shape with your base color.
- Use Adjustments → Liquify with the Push mode to nudge the edges until the volume feels right.
Sketch the full head first, even if the face will be covered or cropped. Hair that is drawn without a skull underneath tends to come out too small or too large, and the hairline and parting won't sit naturally.
Study the curl type before you draw it
Curls aren't a single shape. A loose wave, a spiral ringlet, and a tight coil all behave differently, and mixing them accidentally is what makes a drawing feel off.
- Wavy (type 2): S-shaped bends with little full rotation.
- Curly (type 3): defined spirals with real volume that don't lie flat to the head.
- Coily (type 4): tight, dense curls where the overall silhouette matters more than any single curl.
Pull a reference photo into Procreate and keep it nearby while you work. Before drawing, mark the direction of flow with a few arrows on a throwaway layer. Notice the starting point, usually the parting or crown, where the hair radiates from. Curls in the same section tend to travel the same way, even when they twist around each other.
Three ways to construct a curl
You don't need to commit to one method. Different areas of the same head often call for different approaches.
The wavy ribbon method
Draw one wavy line, then draw a second line beside it that doesn't perfectly mirror the first. The space between them becomes a ribbon of hair that pinches and swells. The pinched spots are where the ribbon turns away from you and are your natural shadow areas. The wide spots are where it faces the light.
This is the best method for loose curls and waves because it forces volume into the shape from the start.
The S-stroke method
Using short, confident S-shaped strokes, stack them along the flow line like links in a chain. Overlap each S slightly with the one before it. Keep strokes short rather than drawing one long continuous spring. A single unbroken coil looks like a telephone cord; a series of overlapping shorter strokes looks like hair.
The staircase method
For ringlets, draw a loose zigzag down the flow direction, then round the corners into loops. This gives you consistent spacing and rotation, which helps when you need the curls to look uniform, such as stylized characters or repeating motion cycles.
Build tone in layers
Once the base and construction are in place, layer color the way you would in a compositing package: separate, adjustable passes.
Shadow pass
Create a new layer above the base and turn on Clipping Mask. Using a darker shade than the base, draw curls in the recessed areas: under the volume, near the scalp, and where one curl passes behind another. Clipping to the base keeps the shadows from spilling outside your silhouette, and you can still edit the base underneath.
Midtone pass
On another layer, use a color close to your base, slightly lighter. Draw curls across the whole shape, and this time let some strokes extend past the base edge. Real curls break the silhouette with stray loops, and the overshoot makes the outline look organic instead of cut out. Skip the clipping mask here on purpose.
Highlight pass
Use your lightest tone on a final layer, concentrated where light would hit the tops of curls. Keep strokes shorter than in the previous passes and don't cover the whole head. Highlights work because they're sparse.
Cleanup and blending
Use layer opacity and blend modes to tune the result without repainting. A soft brush at low opacity on the transitions can smooth any harsh jumps between tones. Use Liquify again at this point to tighten silhouette issues.
Brush and settings choices that matter
You don't need a custom hair brush set, though one can speed things up. Default Procreate brushes can do the whole job:
- A 6B pencil or similar for the initial sketch.
- A calligraphy or script brush for the base outline and curl strokes, since pressure variation gives tapered ends.
- A round brush or brush pen for color and rendering.
- A textured chalk brush if you want a rougher, more painterly finish.
Common mistakes to avoid
- Drawing every strand. Group hair into chunks and let the rendering imply the rest.
- Uniform curl size. Vary the width and length of curls, with tighter ones near the scalp or underneath.
- Ignoring flow. If curls point in random directions with no origin, the hair looks like a wig.
- Flat value. Without a clear dark-to-light structure, curls become a pattern instead of a form.
- One layer for everything. You lose any ability to correct or hand the file off.
Organizing the file for animation
If these curls are heading into a motion project, layer discipline pays off. Name groups clearly (base, shadow, midtone, highlight, flyaways), keep the background transparent, and work at a resolution you can actually deliver at.
A quick workflow summary
- Sketch the head and place the hair's starting point.
- Fill a base silhouette and refine it with Liquify.
- Mark flow direction on a reference layer.
- Construct curls with the wavy ribbon, S-stroke, or staircase method.
- Layer shadows (clipped), midtones, and highlights on separate layers.
- Adjust with blend modes and opacity.
- Organize your layers for animation or compositing.
Once you understand that curls are volume first and detail second, the drawing process becomes repeatable. And if the next step is movement, a clean, layered Procreate file gives you the best possible starting point.