How to Draw and Fill Shapes in Procreate
StyleFrame Team7 min read
To draw and fill a shape in Procreate, draw a closed outline on its own layer (hold your Pencil at the end of a stroke to snap it with QuickShape), then drag your active color from the top-right into the shape. This is ColorDrop. Before you lift, slide left or right to adjust the threshold so the fill reaches the edges without leaking. For more control, use Selections with Color Fill turned on, Alpha Lock for recoloring existing shapes, or Fill Layer for a full-layer fill.
Draw the Shape First
A fill is only as clean as the outline it sits inside, so build the shape carefully.
Use QuickShape for clean geometry
Draw a rough circle, line, or polygon and keep your Pencil on the screen at the end of the stroke. Procreate snaps the stroke into a perfect shape. From there you can tap the edit option that appears at the top to adjust it. A drawn line that snaps into a polyline can be edited point by point. You can also build a shape as a series of connected lines instead, as long as the ends meet.
Close the outline completely
ColorDrop floods outward from the point you drop on and stops at borders. If the outline has even a small gap, the color escapes and fills the entire layer or canvas. If a fill goes everywhere, undo it with a two-finger tap. Then either close the gap or lower the threshold.
Pick a brush that suits fills
A hard, opaque brush such as a monoline gives the most reliable fills. Textured brushes like chalk leave semi-transparent gaps and light patches in the line. The fill won't always reach those edges, so you can end up with a visible mismatch between the flat fill and the grainy outline. If you want a textured look, a common approach is to fill on a separate layer beneath the line work, so the grain stays on top.
Keep shapes on separate layers
Put each shape or group of shapes on its own layer. Layer separation makes later recoloring, masking, and export far easier, and it matters most if you plan to bring the artwork into a compositing pipeline.
Fill with ColorDrop
ColorDrop is the primary fill method in Procreate and works like a paint bucket you drag into place.
- Choose a color, or open a palette so swatches are available.
- Drag the color circle from the top-right into the closed shape.
- Keep your Pencil or finger down after the color floods in.
- Slide left to reduce the threshold or right to increase it. The percentage appears at the top of the canvas.
- Lift to commit the fill.
Procreate remembers the threshold until you change it again, which is useful when you're filling many similar shapes.
Continue Filling for multiple areas
After a ColorDrop, tap Continue Filling to fill other areas with simple taps. You can also tap, hold, and drag to adjust the threshold on each fill. Exit by tapping the checkmark or switching to another tool. If your iPad and Pencil support hover, you can hover over the active color and double-tap the Pencil to jump straight into Continue Filling.
Fixing a threshold that is too high or too low
- Fill covers everything: the threshold may be too high, or the outline may have a gap. Lower the threshold first, then check the line work.
- White specks along the edges: the threshold is likely too low, or the line is made with a semi-transparent textured brush. Raise it gradually, a few percentage points at a time.
- Fill ignores your shape on another layer: ColorDrop reads the layer you're on. If the outline is on a different layer, the active layer looks empty and the whole layer fills. Set the outline layer as a Reference layer so the fill detects it, or put the fill on the same layer as the outline.
Other Ways to Fill Shapes
ColorDrop isn't always the best tool. Procreate offers several alternatives for different situations.
Selections with Color Fill
This method fills an area at the moment you make the selection, which works well for geometric shapes.
- Tap Selections.
- Choose a method: Automatic, Freehand, Rectangle, or Ellipse.
- Turn on Color Fill so it is highlighted.
- Pick your color from the top-right.
- Make your selection. The color fills as soon as the selection completes.
Color Fill stays on between sessions, so turn it off when you're done or you'll fill things by accident. It only works on a single layer, not a group. Combine it with Feather to soften the edges of rectangle fills, which suits soft framing shapes.
Recolor through QuickMenu
Recolor is a tap-to-fill tool that sits outside the normal toolbar. To use it, enable QuickMenu under Actions → Prefs → Gesture Controls, and assign Recolor to one of its radial slots. Then pick a color, tap areas to fill them, and use the Flood slider to control how aggressively the fill spreads. It is an alternative to ColorDrop and Continue Filling.
Fill Layer
If you want a layer filled entirely with one color, pick the color, open Layers, tap the layer, and choose Fill Layer from the options. This is a good way to create a solid background or a flat base to mask or clip other artwork onto.
Alpha Lock for recoloring existing shapes
Alpha Lock restricts painting to pixels that already exist on a layer. Turn it on for a shape layer, then paint, fill, or add gradients and they stay inside the shape without spilling out. This is the cleanest way to change a shape's color after the fact, and it avoids threshold problems entirely.
Fill Shapes with Gradients and Patterns
Solid fills are only the start. Two techniques cover most needs.
Gradients
Turn on Alpha Lock for the shape layer, then paint a gradient directly onto it. Alternatively, fill the shape with black on one layer, add a gradient layer directly above it, and set that layer's blend mode to Lighten. The gradient then shows only where it is lighter than the black beneath it. This keeps the gradient separate from the shape, so you can edit it independently.
Patterns and textures
Place a pattern layer above your shape layer and set it as a Clipping Mask. The pattern then appears only inside the shape below. You can import a pattern or create one yourself. Because the shape and pattern remain separate layers, you can swap patterns without redrawing anything.
Prepare Procreate Shapes for Motion Work
Many motion designers use Procreate to create shape-based artwork: icons, character parts, texture elements, and style frames. A few habits make that artwork easier to use downstream.
- Name and separate layers. One element per layer is far easier to animate or composite than a flattened image.
- Fill cleanly. Check zoomed-in edges for white specks or fringing. These show up badly once the artwork is scaled or composited over footage.
- Work at a high canvas resolution. Starting large leaves room for scaling in your compositing tool.
- Export what you need. Flattened PNGs suit reference frames, while layered files suit rebuilding the artwork in After Effects.
Where Styleframe Fits
Once shapes are filled and cleaned up, the same artwork can also be used as reference material for AI-assisted motion tools such as , rather than staying as a still.
Quick Troubleshooting Checklist
- Fill floods the whole canvas: look for gaps in the outline, lower the threshold, and confirm that you're on the right layer or have set a Reference layer.
- Gaps or specks remain inside the shape: raise the threshold slowly, or switch to a harder, more opaque brush for the outline.
- Color Fill isn't working on a group: it only works on a single layer. Select one layer instead.
- Selections keep filling unexpectedly: Color Fill is still on. Turn it off in the Selections menu.
- Color spills outside a shape when recoloring: use Alpha Lock on the shape layer instead of ColorDrop.
Summary
For most work, draw a closed shape on its own layer and drag the color into it with ColorDrop, adjusting the threshold before you lift. Use Selections with Color Fill for precise geometric fills, Alpha Lock for safe recoloring and gradients, and Clipping Masks for patterns. Keep layers separate and edges clean, and your Procreate shapes will be ready for animation, compositing, or reference-driven work in tools like Styleframe, After Effects, and Nuke.